ISO TS 19072-4-2012 Road vehicles - Connection interface for pyrotechnic devices two-way and three-way connections - Part 4 Pyrotechnic device and harness conne.pdf

《ISO TS 19072-4-2012 Road vehicles - Connection interface for pyrotechnic devices two-way and three-way connections - Part 4 Pyrotechnic device and harness conne.pdf》由会员分享，可在线阅读，更多相关《ISO TS 19072-4-2012 Road vehicles - Connection interface for pyrotechnic devices two-way and three-way connections - Part 4 Pyrotechnic device and harness conne.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2012 Road vehicles Connection interface for pyrotechnic devices, two-way and three-way connections Part 4: Pyrotechnic device and harness connector assembly - type 2 Vhicules routiers Interface de raccordement pour dispositifs pyrotechniques, deux voies et trois voies Partie 4: Assemblage du di

2、spositif pyrotechnique et du connecteur faisceau - type 2 TECHNICAL SPECIFICATION ISO/TS 19072-4 First edition 2012-09-15 Reference number ISO/TS 19072-4:2012(E) ISO/TS 19072-4:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specifi

3、ed, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case

4、 postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO/TS 19072-4:2012(E) ISO 2012 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 T erms and definitions .

5、 1 4 Dimensional features and performance requirements . 2 4.1 General . 2 4.2 Retainer and squib holder assembly 3 4.3 Codings and polarization . 3 4.4 Dimensional features and properties for shorting clip function . 5 4.5 Dimensional features and properties for shorting clip function . 7 5 Materia

6、l characteristics 7 5.1 Contacts clip contact specifications 7 5.2 Retainer . 7 Annex A (normative) Three-way (with ground) variant of the pyrotechnic device/initiator harness connector assembly . 8 ISO/TS 19072-4:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwi

7、de federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on tha

8、t committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in a

9、ccordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard re

10、quires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to publish other types of document: an ISO Publicly Available Specification (ISO/PAS) represents

11、an agreement between technical experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee casting a vote; an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical committee and i

12、s accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS

13、or ISO/TS is confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an International Standard or be withdrawn. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be

14、 held responsible for identifying any or all such patent rights. ISO/TS 19072-4 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic equipment. ISO 19072 consists of the following parts, under the general title Road vehicles Connection interface

15、for pyrotechnic devices, two-way and three-way connections: Part 1: Pocket interface definition Part 2: Test methods and general performances requirements Part 3: Pyrotechnic device and harness connector assembly type 1 Technical Specification Part 4: Pyrotechnic device and harness connector assembl

16、y - type 2 Technical Specification iv ISO 2012 All rights reserved ISO/TS 19072-4:2012(E) Introduction Road vehicles integrate an increasing number of pyrotechnic devices contributing to occupant safety in vehicles (for example frontal and side air bag, safety belt pretensioner, etc.). T o build the

17、 complete system requires a requires a supply of various components from several different equipment suppliers. Vehicle manufacturers need to define a common specification to ensure that connectors designed and produced for the various equipment suppliers can be mated without any difficulty. In the

18、current design of this vehicle equipment, three areas of connection have been identified: connection between the pyrotechnic device (e.g. initiator) and the harness connector; connection between the tab holder and the clip holder of the harness connector; connection between the harness connector and

19、 the electronic control module. The connection between the pyrotechnic device and the harness connector is the only connection that can be standardised and it forms the subject of this Technical Specification. Due to the location of the safety device in the vehicle, the connector design could be rig

20、ht angle or straight. Due to the fact that several electrostatic discharge (ESD) protection levels are requested by vehicle manufacturers, a three-way or a two-way without ground option of the pyrotechnic device/initiator harness connector assembly is also defined. The International Organization for

21、 Standardization (ISO) draws attention to the fact it is claimed that compliance with this document may involve the use of a patent. ISO take no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured the ISO that he is willing to negoti

22、ate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with ISO. Information may be obtained from: FCI 145, rue Yves-Le-Coz 78000 Versailles France Attention is dr

23、awn to the possibility that some of the elements of this document may be the subject of patents rights other than those identified above. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2012 All rights reserved v Road vehicles Connection interface for pyrotechnic

24、 devices, two-way and three-way connections Part 4: Pyrotechnic device and harness connector assembly - type 2 1 Scope This Technical Specification defines the general minimum specifications of a type 2 two-way connection interface, linking the pyrotechnic device and harness connector built into a r

25、oad vehicle. A three-way with ground variant of the pyrotechnic device/initiator harness connector assembly is also defined (see Annex A). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap

26、plies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 178, Plastics - Determination of flexural properties ISO 8092-2, Road vehicles - Connections for on-board electrical wiring harnesses Part 2: Definitions, test methods and general per

27、formance requirements ISO 14647, Metallic coatings Determination of porosity in gold coatings on metal substrates Nitric acid vapour test ISO 19072-1, Road vehicles Connection interface for pyrotechnic devices, two-way and three-way connections Part 1: Pocket interface definition ISO 19072-2, Road v

28、ehicles Connection interface for pyrotechnic devices, two-way and three-way connections Part 2: Test methods and general performance requirements ISO 27874, Metallic and other inorganic coatings Electrodeposited gold and gold alloy coatings for electrical, electronic and engineering purposes Specifi

29、cation and test methods RAL colour space system, RAL German Institute for Quality Assurance and Certification e.V. 3 T erms an d definiti ons For the purposes of this document, the terms and definitions given in ISO 8092-2 and the following apply. 3.1 connector assembly of contact and housing that t

30、erminates conductors for the purpose of providing connection and disconnection to a suitable mating connector NOTE A male (female) connector is a housing containing male (female) contacts and accessory items. A male connector can be permanently fixed to a wiring harness or to an appliance, e.g. an e

31、lectronic control unit (ECU). A female connector is, in general, permanently fixed to a wiring harness. TECHNICAL SPECIFICATION ISO/TS 19072-4:2012(E) ISO 2012 All rights reserved 1 ISO/TS 19072-4:2012(E) 3.2 housing connector without its contacts 3.3 initiator part of the pyrotechnical device with

32、two male contacts 3.4 pocket squib holder inner interface including male contacts 3.5 retainer ring, generally made of plastic, holding an optional shorting clip and providing coding and electrical insulation NOTE The shorting clip may be omitted by decision between manufacturer and supplier. 3.6 sh

33、orting clip shunt metallic bar of the retainer providing the electrical connection between two male contacts 3.7 squib holder part of the pyrotechnic device holding the initiator and the retainer 4 Dimensional features and performance requirements 4.1 General The female connector shall be designed t

34、o avoid damage to male contacts and the initiator in the case of improper mating. See Figure 1. Figure 1 Example of scoop proof design Connector, retainer and squib holder assembly shall comply with requirements in ISO 19072-1 and ISO 19072-2. 2 ISO 2012 All rights reserved ISO/TS 19072-4:2012(E) 4.

35、2 Retainer and squib holder assembly The dimensions of the retainer shall comply with Figure 1. The dimensions of the squib holder interface are defined in ISO 19072-1. Dimensions in millimetres Key 1 squib holder 2 shorting clip NOTE Not dimensioned features are not part of the interface descriptio

36、n. Figure 2 Retainer and squib holder assembly 4.3 Codings and polarization Coding and polarization are determined by the dimensions and position of the coding keys, each of which has its own colour code (see Figure 2 and Table 1). The colour code shall be in accordance with RAL 1) ; however, there

37、needs to be an agreement about the range between the customer and supplier. Dimensions in millimetres. a) Coding I 1) RAL colour space system developed by Reichsausschu fr Lieferbedingungen und Gtesicherung (German Institute for Quality Assurance and Certification e. V.): https:/www.ral-farben.de/.

38、ISO 2012 All rights reserved 3 ISO/TS 19072-4:2012(E) b) Coding II c) Coding III d) Coding IV a Optional label, indicating the coding by roman numerals. NOTE Not dimensioned features are not part of the interface description. Figure 3 Dimensions and position of coding keys 4 ISO 2012 All rights rese

39、rved ISO/TS 19072-4:2012(E) Table 1 Type of coding used and assigned colour code Colours RAL Connection Two-way Three-way No. Colour description I II III IV I II III IV 9011 Graphite black X 6027 Light green X 1021 Yellow X 4005 Blue purple X 2007 Luminous bright orange X 4008 Signal violet X 6017 M

40、ay green X 9003 Signal white X 4.4 Dimensional features and properties for shorting clip function Dimensions in millimetres a) ISO 2012 All rights reserved 5 ISO/TS 19072-4:2012(E) b) Key 1 parting line 2 chamfer 0,8 30 (2) a Minimum adjusted to dimensions of the inserted clip. b Edge free of burrs,

41、 radius or chamfer allowed. c Optional chamfer for radius. d Dimensioning points relate to theoretical intersection points. e Flattening optional for manufacturing purposes. NOTE Not dimensioned features are not part of the interface description. Figure 4 Dimensions of area for actuating short-circu

42、it opening in retainer 6 ISO 2012 All rights reserved ISO/TS 19072-4:2012(E) 4.5 Dimensional features and properties for shorting clip function The dimensional features and properties for the shorting clip function shall comply with Figure 4. Dimensions in millimetres a) Connector is in contact, sho

43、rting clip closed b) Connector mated, with position assurance (CPA), shorting clip open NOTE Not dimensioned features are not part of the interface description. Figure 5 Dimensions of area and opening distance of shorting-clip 5 Material characteristics 5.1 C ontacts clip c ontact specifications The

44、 contact area for the shorting clip (see Figure 3) shall comply with the following characteristics: ISO 27874, type (coating purity) and class (coating thickness) to be agreed between customer and supplier, but not less than class 0,5; ISO 14647, porosity not greater than 2 pores/mm 2 . 5.2 Retainer

45、 The modulus of elasticity of the plastic used for the retainer shall be at least 4 500 MPa, in compliance with ISO 178. ISO 2012 All rights reserved 7 ISO/TS 19072-4:2012(E) Annex A (normative) Three-way (with ground) variant of the pyrotechnic device/ initiator harness connector assembly The speci

46、fications in Clauses 1 to 5 also apply to the three-way with ground variant of the pyrotechnic device/initiator harness connector assembly. The dimensions of the actuation area for closing the ground contact shall comply with Figure A.1. The contact area of the ground function shall comply with the

47、following characteristics: plating material: tin, thickness of plating: 2 m to 5 m. All contents of the main document are applicable for the three-way design. Dimensions in millimetres aNominal forces between 2 N and 8 N shall be maintained within the dimension indicated. Figure A.1 Dimensions of area and nominal forces for ground contact 8 ISO 2012 All rights reservedISO/TS 19072-4:2012(E) ISO 2012 All rights reserved IC S 43.040.10 Price based on 8 pages