ISO IEC 14575-2000 Information Technology - Microprocessor Systems - Heterogeneous InterConnect (HIC) (Low-Cost Low-Latency Scalable Serial Interconnect for Par.pdf

《ISO IEC 14575-2000 Information Technology - Microprocessor Systems - Heterogeneous InterConnect (HIC) (Low-Cost Low-Latency Scalable Serial Interconnect for Par.pdf》由会员分享，可在线阅读，更多相关《ISO IEC 14575-2000 Information Technology - Microprocessor Systems - Heterogeneous InterConnect (HIC) (Low-Cost Low-Latency Scalable Serial Interconnect for Par.pdf（166页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD ISO/IEC 14575 IEEE Std 1355 First edition 2000-07 Information Technology Microprocessor Systems Heterogeneous InterConnect (HIC) (Low-Cost, Low-Latency Scalable Serial Interconnect for Parallel System Construction) Reference number ISO/IEC 14575:2000(E) IEEE Std 1355, 1998 Edi

2、tionAbstract: Enabling the construction of high-performance, scalable, modular, parallel systems with low system integration cost is discussed. Complementary use of physical connectors and cables, electrical properties, and logical protocols for point-to-point serial scalable interconnect, operating

3、 at speeds of 10 200 Mb/s and at 1 Gb/s in copper and optic technologies, is described. Keywords: flow control, encoding schemes, OMI/HIC, packet routing, parallelism, point-to- point serial scalable interconnect, protocols, routing fabric, serial links, serialization, silicon integration, switch ch

4、ip, transaction layer, wormhole routing. The Institute of Electrical and Electronics Engineers, Inc. 345 East 47th Street, New York, NY 10017-2394, USA Copyright 1998 by the Institute of Electrical and Electronics Engineers, Inc. All rights reserved. First published in 1998. ISBN 2-8318-5321-4 No pa

5、rt of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.INTERNATIONAL STANDARD ISO/IEC 14575 IEEE Std 1355 First edition 2000-07 Information Technology Microprocessor Systems Heterogeneous InterConnec

6、t (HIC) (Low-Cost, Low-Latency Scalable Serial Interconnect for Parallel System Construction) Sponsor Bus Architecture Standards Committee of the IEEE Computer Society PRICE CODE XC For price, see current catalogue 2 ISO/IEC 14575:2000(E) IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights r

7、eserved. CONTENTS Page FOREWORD 8 INTRODUCTION 9 Clause 1 Scope and object . 15 2 Normative references. 15 3 Definitions 17 3.1 General. 17 3.2 Glossary . 17 4 Physical media and logical layers . 23 4.1 Physical media 23 4.2 Logical layers 24 4.3 Interaction of layers. 27 4.4 Implementations defined

8、 in this International Standard 29 5 DS-SE and DS-DE . 31 5.1 General. 31 5.2 DS-SE: physical medium . 32 5.3 DS-SE signal level 32 5.4 DS-DE: physical medium. 38 5.5 DS-DE signal level 44 5.6 DS-SE and DS-DE character level. 46 5.7 DS-SE and DS-DE exchange level 48 6 TS-FO-02 fiber optic link 51 6.

9、1 Physical medium. 51 6.2 Signal level . 53 6.3 TS-FO character level . 55 6.4 TS-FO exchange level. 57 7 HS-SE-10.62 7.1 HS-SE physical medium 62 7.2 HS-SE signal level 66 7.3 HS character level (8B/12B code) 69 7.4 HS exchange level 86 8 HS-FO-10 fiber optic link 94 8.1 Physical medium. 94 8.2 Sig

10、nal level . 97 8.3 Character level and exchange level . 99 9 Common packet level. 99 9.1 General discussion 99 9.2 Packet format . 99 9.3 Networks and routing 100 9.4 Error detection, recovery, and reporting. 101 10 Conformance criteria 101 10.1 Conformance statements 101 10.2 Definition of subsets

11、101ISO/IEC 14575:2000(E) 3 IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights reserved. Annex A (normative) DS-DE connector specification 103 Annex B (normative) HS-SE connector specification 110 Annex C (normative) TS-FO and HS-FO connector specifications 116 Annex D (informative) Rational

12、e 128 Annex E (informative) Switch chips, switches, and fabrics 132 Annex F (informative) Use of the transaction layer Asynchronous transfer mode (ATM) example . 134 Annex G (informative) Error handling . 145 Annex H (informative) Flow control calculations . 146 Annex I (informative) Synchronized ch

13、annel communications . 149 Annex J (informative) Example DS-SE driver circuit . 152 Annex K (informative) DS-DE optional power supply recommendation 154 Annex L (informative) DS-DE fixed connector PCB recommendation 155 Annex M (informative) DS-DE cable (10 core) recommendation 156 Annex N (informat

14、ive) DS-DE multiway connector housing recommendation. 157 Annex O (informative) HS-SE fixed connector PCB recommendation 158 Annex P (informative) HS-SE cable recommendation . 159 Annex Q (informative) HS-SE connector multiway housing recommendation. 160 Annex R (informative) TS/HS-FO connector PCB

15、and front panel cut-out recommendation. 161 Annex S (informative) TS/HS-FO fiber cable recommendation 162 Figure 1 Protocol stack between nodes 23 Figure 2 Exchange layer 26 Figure 3 Protocol stack diagram showing interaction of layers 28 Figure 4 Defined implementation of physical and logical layer

16、s. 30 Figure 5 DS-SE link signal propagation 33 Figure 6 DS-SE timing reference model . 35 Figure 7 DS-SE link timings . 36 Figure 8 DS-SE link signal encoding 37 Figure 9 DS-DE cable assembly twist example. 40 Figure 10 DE-DE extension adapter . 40 Figure 11 DS-DE fixed connector external view 41 F

17、igure 12 Multiple power connectors 43 Figure 13 DS-SE/DS character encoding 46 Figure 14 DS-SE/DS-DE parity coverage 47 Figure 15 DS link states. 49 Figure 16 DS link start-up and reset. 50 Figure 17 TS-FO cable fibers/plugs wiring 52 Figure 18 TS-FO extension adapter . 52 Figure 19 TS-FO fixed adap

18、tor, external view and ferrule allocation 53 Figure 20 TS-FO reference list. 54 Figure 21 TS-FO link states . 58 Figure 22 TS link start-up and reset . 59 4 ISO/IEC 14575:2000(E) IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights reserved. Figure 23 TS-FO packet encoding 61 Figure 24 Single

19、 braid and double braid link cables 64 Figure 25 HS-SE cable pins/connectors wiring . 65 Figure 26 HS-SE extension adapter . 65 Figure 27 HS-SE fixed connector external view 65 Figure 28 Input and output buffer electrical model 67 Figure 29 Exchange level interconnection between two nodes 87 Figure

20、30 Transmitter state machine controller-start-up 88 Figure 31 Transmitter state machine controller-functional. 89 Figure 32 Transmitter state machine controller-shutdown. 89 Figure 33 Receiver state machine controller. 90 Figure 34 Exchange for start-up, functional and shutdown 91 Figure 35 Exchange

21、 for bidirectional start-up . 92 Figure 36 HS-FO cable fibers/plugs wiring . 95 Figure 37 HS-FO extension adapter . 96 Figure 38 HS-FO fixed adapter, external view and ferrule allocation . 96 Figure 39 HS-FO reference link . 98 Figure A.1 DS-DE fixed connector front view 105 Figure A.2 DS-DE fixed c

22、onnector side view. 106 Figure A.3 DS-DE fixed connector top view 106 Figure A.4 DS-DE connector latch 107 Figure A.5 DS-DE free connector front view . 108 Figure A.6 DS-DE free connector side view 109 Figure A.7 DS-DE free connector contact. 109 Figure B.1 HS-SE free connector front view . 112 Figu

23、re B.2 HS-SE free connector side view 112 Figure B.3 HS-SE fixed connector front view 113 Figure B.4 HS-SE fixed connector side view. 113 Figure B.5 HS-SE connector link 114 Figure B.6 HS-SE contact interface dimensions . 115 Figure C.1 TS-FO/HS-FO link free connector . 126 Figure C.2 TS-FO/HS-FO li

24、nk fixed connector 127 Figure F.1 ATM network. 134 Figure F.2 ATM layers . 136 Figure F.3 Virtual channels and virtual paths 137 Figure F.4 Example of virtual path and virtual channel switching. 138 Figure F.5 ATM cell header 139 Figure F.6 Mapping reference model 140 Figure H.1 Theoretical maximum

25、transmission length calculation . 147 Figure H.2 Distance versus buffer size for DS and TS links 147ISO/IEC 14575:2000(E) 5 IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights reserved. Figure H.3 Distance versus buffer size for HS-SE links 148 Figure J.1 DS-SE pad equivalent circuit . 153 F

26、igure J.2 Simulation input waveforms. 153 Figure K.1 Optional power supply circuit. 154 Figure L.1 DS-DE fixed connector PCB layout 155 Figure M.1 Recommended DS-DE link cable cross-section. 156 Figure N.1 DS-DE connector multiway housing. 157 Figure N.2 DS-DE (multiway) front panel cut-out 157 Figu

27、re P.1 Recommended HS-SE link shielded cable cross-section 159 Figure O.1 Recommended HS-SE fixed connector PCB layout . 158 Figure Q.1 HS-SE multiway housing. 160 Figure Q.2 HS-SE (multiway) front panel cut out 160 Figure R.1 TS/HS-FO fixed connector PCB footprint. 161 Figure R.2 TS/HS-FO fixed con

28、nector front panel cut-out . 161 Figure S.1 Example of TS/HS-FO fiber cable structure. 162 Table 1 Identification format for technologies . 30 Table 2 Defined implementations . 31 Table 3 Driver to line impedance matching table 34 Table 4 DS-SE input capacitance. 34 Table 5 DS-SE timing and swings 3

29、5 Table 6 DS-SE output skew parameters. 37 Table 7 Identification of multiple link interfaces 38 Table 8 DS-DE cable color code 38 Table 9 Electrical and mechanical characteristics and safety certification of DS-DE cable. 39 Table 10 DS-DE link cable conductors/connectors wiring . 40 Table 11 Pin al

30、location of DS-DE connector . 41 Table 12 DS-DE connector modularity specifications 41 Table 13 DS-DE environmental constraints 42 Table 14 Optional power supply . 42 Table 15 Optional power supply load 42 Table 16 Optional power supply protective device 43 Table 17 DS-DE signal levels. 44 Table 18

31、DS-DE correspondence. 45 Table 19 Attribution of attenuation budget 45 Table 20 Attribution of skew budget . 45 Table 21 Terminator character codings 47 Table 22 Link control character codings . 47 Table 23 Summary of main optical characteristics of TS-FO fibers . 51 Table 24 TS-FO connector modular

32、ity specifications 52 Table 25 TS-FO signal allocation . 53 Table 26 TS-FO environmental constraints. 53 Table 27 TS-FO recommended transceiver characteristics. 54 6 ISO/IEC 14575:2000(E) IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights reserved. Table 28 TS-FO link performance specificat

33、ion 55 Table 29 Symbols allocated for character coding of data values . 56 Table 30 Symbols for control characters 56 Table 31 Coding of control characters 57 Table 32 Coding of INIT. 57 Table 33 HS-SE-10 links general characteristics 62 Table 34 PCB track characteristics 62 Table 35 Physical charac

34、teristics of a single coaxial cable . 63 Table 36 Electrical characteristics of a single coaxial cable 63 Table 37 Mechanical performance and safety certification of link cables. 64 Table 38 Pin allocation of HS-SE connector . 66 Table 39 HS-SE environmental constraints 66 Table 40 HS-SE environment

35、al constraints 66 Table 41 Operating rates for HS-SE-10 links 66 Table 42 Attribution of attenuation budget 68 Table 43 Driver side line logic levels for V DD= 3.3 V (nominal). 68 Table 44 Driver side line logic levels for V DD= 5.0 V (nominal). 68 Table 45 Driver side line swing when ac coupled int

36、o 50 termination. 68 Table 46 Receiver electrical characteristics 69 Table 47 Data characters. 72 Table 48 Control characters. 83 Table 49 Reserved L_chars for exchange level functions . 87 Table 50 Time-out values. 92 Table 51 Summary of main optical characteristics of HS-FO fibers. 95 Table 52 THS

37、-FO connector modularity specifications 95 Table 53 HS-FO signal allocation. 96 Table 54 HS-FO environmental constraints 96 Table 55 HS-FO recommended transceiver characteristics for multimode fiber. 97 Table 56 HS-FO recommended transceiver characteristics for single mode fiber 97 Table 57 HS-FO li

38、nk performance specification 98 Table 58 End_of_packet markers. 100 Table 59 Codes for EOP markers. 100 Table 60 Conformance identifications for connectors 101 Table 61 Conformance identifications for link cables 101 Table 62 Conformance identifications for link cable assemblies 102 Table 63 Common

39、identifications for link interfaces 102 Table A.1 DS-DE connector requirements 103 Table B.1 HS-SE connector requirements 110ISO/IEC 14575:2000(E) 7 IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights reserved. Table C.1 TS-FO and HS-FO (multimode) connector requirements. 116 Table C.2 Perfo

40、rmance and environmental specification for TS-FO and HS-FO (multimode) connector 119 Table C.3 HS-FO (single-mode) connector requirements 121 Table C.4 Performance and environmental specification for HS-FO (single-mode) connector . 124 Table C.5 Color coding of TS/HS-FO connectors 127 Table J.1 Para

41、meter spread for DS-SE link driver 152 Table L.1 PCB details for DS-DE connector attachment . 155 Table M.1 Recommended DS-DE link cable specification . 156 Table P.1 Recommended HS-SE cable specifications 159 8 ISO/IEC 14575:2000(E) IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights reserv

42、ed. International Electrotechnical Commission 3, rue de Varemb, PO Box 131, CH-1211-Geneva 20, Switzerland Telephone: +41 22 919 0211 Telefax: +41 22 919 0300 e-mail: inmailiec.ch URL: http:/www.iec.ch INFORMATION TECHNOLOGY MICROPROCESSOR SYSTEMS HETEROGENEOUS INTERCONNECT (HIC) (LOW-COST, LOW-LATE

43、NCY SCALABLE SERIAL INTERCONNECT FOR PARALLEL SYSTEM CONSTRUCTION) FOREWORD 1) ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC pa

44、rticipate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governme

45、ntal and non-governmental, in liaison with ISO and IEC, also take part in the work. 2) In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC1. Draft International Standards adopted by the joint technical committee are circulated to national bod

46、ies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. 3) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO and IEC shall not be held resp

47、onsible for identifying any or all such patent rights. International Standard ISO/IEC 14575 was prepared by subcommittee 26: Microprocessor systems, of ISO/IEC joint technical committee 1: Information technology. International Standards are drafted in accordance with ISO/IEC Directives, Part 3. Anne

48、xes A, B and C form an integral part of this standard. Annexes D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R and S are for information only.ISO/IEC 14575:2000(E) 9 IEEE Std 1355, 1998 Edition Copyright 1998 IEEE. All rights reserved. INTRODUCTION (This introduction is not a normative part of ISO/IEC 14575:2000, but is included for information only.) The construction of high-performance systems with parallel communications, parallel processing, and/or parallel I/O demands a fast, low-cost, low-latency interco