ISO 9051-2001 Glass in building - Fire-resistant glazed assemblies containing transparent or translucent glass for use in building《建筑玻璃 用于建筑中装有耐火透明或半透明玻璃的装置》.pdf

《ISO 9051-2001 Glass in building - Fire-resistant glazed assemblies containing transparent or translucent glass for use in building《建筑玻璃 用于建筑中装有耐火透明或半透明玻璃的装置》.pdf》由会员分享，可在线阅读，更多相关《ISO 9051-2001 Glass in building - Fire-resistant glazed assemblies containing transparent or translucent glass for use in building《建筑玻璃 用于建筑中装有耐火透明或半透明玻璃的装置》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONALSTANDARDISO9051Second edition2001-08-15Reference numberISO 9051:2001(E) ISO 2001Glass in building Fire-resistant glazedassemblies containing transparent ortranslucent glass, for use in buildingVerre dans la construction Ensembles vitrs rsistant au feu, comportantdu verre transparent ou

2、translucide, pour utilisation dans le btimentCopyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 9051:2001(E)ii ISO 2001 All rights reservedPDF disclaimerThis PDF file ma

3、y contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not beedited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,parties accept therein the respon

4、sibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation p

5、arameterswere optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely eventthat a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2001All rights reserved. Unless otherwi

6、se specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs mem-ber body in the country of the requester.ISO copyright

7、officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.chWeb www.iso.chPrinted in SwitzerlandCopyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without lic

8、ense from IHS-,-,-ISO 9051:2001(E) ISO 2001 All rights reserved iiiForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISOmember bodies). The work of preparing International Standards is normally carried out through ISO technicalco

9、mmittees. Each member body interested in a subject for which a technical committee has been established hasthe right to be represented on that committee. International organizations, governmental and non-governmental, inliaison with ISO, also take part in the work. ISO collaborates closely with the

10、International ElectrotechnicalCommission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.Draft International Standards adopted by the technical committees are circulated to the member bo

11、dies for voting.Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this International Standard may be the subject ofpatent rights. ISO shall not be held responsible for ide

12、ntifying any or all such patent rights.International Standard ISO 9051 was prepared by Technical Committee ISO/TC 160, Glass in building, Subcom-mittee SC 2, Use considerations.This second edition cancels and replaces the first edition (ISO 9051:1990)of which it constitutes a minor revision.Copyrigh

13、t International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or ne

14、tworking permitted without license from IHS-,-,-INTERNATIONAL STANDARD ISO 9051:2001(E) ISO 2001 All rights reserved 1Glass in building Fire-resistant glazed assemblies containingtransparent or translucent glass, for use in building1 ScopeThis International Standard specifies the classification and

15、marking of transparent and translucent glass products,which will be described in future International Standards on basic or processed glass products, in assemblies for usein building and intended to provide some degree of fire-resistance.2 Normative referencesThe following normative documents contai

16、n provisions which, through reference in this text, constitute provisions ofthis International Standard. For dated references, subsequent amendments to, or revisions of, any of these publica-tions do not apply. However, parties to agreements based on this International Standard are encouraged to inv

17、esti-gate the possibility of applying the most recent editions of the normative documents indicated below. For undatedreferences, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain reg-isters of currently valid International Standards.ISO 834-1:1999, Fi

18、re-resistance tests Elements of building construction Part 1: General requirementsISO 3009, Fire resistance tests Elements of building construction Glazed elements3 Fire-resistance characteristics of glazed assembliesGlass is a non-combustible material and therefore will not contribute to or propaga

19、te fire.If affected by heat, glass may fracture by thermal shock or may soften and then not be held by the frame. Only certaintypes of glazed assemblies are, therefore, recognized as fire-resisting. The ability of glazed assemblies to resist firedepends on the type of glass product, glazing method,

20、frame type, pane size, fixing method and the type ofconstruction surrounding the glazed area.Some transparent and translucent glazed assemblies can meet requirements for stability and integrity (RE), and insome cases insulation (REI, where R is for resistance, E for integrity and I for insulation).N

21、ot only is the possibility of direct propagation of fire and smoke through openings caused by glass breakage to beconsidered for fire protection precautions, it may also be necessary to take into account the heat transmitted throughthe glazed assembly, which may still be intact, as such heat may cau

22、se ignition of combustible materials.Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 9051:2001(E)2 ISO 2001 All rights reserved4 ClassesAs glazed assemblies perform d

23、ifferently in case of fire, the type shall be classified into one of the followingcategories.a) Class REGlazed assemblies of fire-resistance according to class RE under the fire conditions as defined in ISO 834-1 pro-vide, for a given time, stability and integrity. The temperature of the unexposed s

24、ide is not taken into account.b) Class REIGlazed assemblies of fire-resistance according to class REI under the fire conditions as defined in ISO 834-1provide, for a given time, stability, integrity and insulation.5 Frame, glass, glazing material and surrounding constructionThe frame, glazing materi

25、al and surrounding construction shall be such that the glazed assembly as a wholecorresponds to the test report.Glazings of class RE could, for example, contain glass blocks, glass with a low coefficient of thermal expansion, or glass ceramics, glass toughened by thermal or chemical treatment, wired

26、 glass, flat glass in small panes, or laminated glass,in single or multiple glazings.Glazings of class REI could, for example, contain some types of glass blocks, or some types of laminated glazings in single or multiple glazings.6 Test requirements6.1 SpecimensA specimen, for the purposes of this I

27、nternational Standard, is a complete glazed assembly.6.2 InstallationThe fixing of the specimen into the furnace opening shall be in accordance with ISO 3009.6.3 ProcedureThe test procedure shall be in accordance with ISO 3009, and for the temperature of the unexposed side (class REI),see ISO 834-1:

28、1999, subclause 5.5.12, with at least one thermocouple for the measurement of the maximum tem-perature on the glazing.Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO

29、9051:2001(E) ISO 2001 All rights reserved 36.4 CriteriaA glazed assembly for fire-resistance class RE shall meet the integrity requirements of ISO 3009 (see Table 1).A glazed assembly for fire-resistance class REI shall meet both the integrity requirements of ISO 3009 and the insu-lation requirement

30、s of ISO 834-1 (see Table 1).7 Test reportThe test report shall state the following information:a) name of test laboratory;b) name of sponsor(s);c) date of tests;d) name(s) of manufacturer(s) and trade name(s) (if any) of the major components of the glazed assembly;e) details of materials, construct

31、ion and conditioning of the assembly tested;f) description of the fixings between the assembly tested and the test frame or surround;g) side exposed to heat;h) test result as determined by the furnace time/pressure chart and temperature curves, and the time(s) at whichparticular criteria in 6.4 are

32、no longer satisfied;i) any other relevant observations;j) fire-resistance class(es) RE and/or REI and code number(s) according to Table 1.8MarkingIf marking is essential, the following particulars shall be indelibly and distinctly marked on every glazed assembly, ina position which is visible to any

33、one requiring the information:a) manufacturers name or trademark;b) the number of this International Standard, i.e. ISO 9051;c) fire-resistance class RE and/or REI;d) code number(s) for the resistance time(s).Table 1 Fire-resistance timeCode number Resistance timemin15 15 to 2930 30 to 4445 45 to 59

34、60 60 to 8990 90 to 119120 120 or moreCopyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 9051:2001(E)ICS 81.040.20Price based on 3 pages ISO 2001 All rights reservedCopyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-