ISO 8791-4-2007 Paper and board - Determination of roughness smoothness (air leak methods) - Part 4 Print-surf method《纸和纸板 粗糙度 平滑度的测定(空气泄漏法) 第4部分 印刷面法》.pdf

《ISO 8791-4-2007 Paper and board - Determination of roughness smoothness (air leak methods) - Part 4 Print-surf method《纸和纸板 粗糙度 平滑度的测定(空气泄漏法) 第4部分 印刷面法》.pdf》由会员分享，可在线阅读，更多相关《ISO 8791-4-2007 Paper and board - Determination of roughness smoothness (air leak methods) - Part 4 Print-surf method《纸和纸板 粗糙度 平滑度的测定(空气泄漏法) 第4部分 印刷面法》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 8791-4:2007(E) ISO 2007INTERNATIONAL STANDARD ISO 8791-4 Second edition 2007-11-15 Paper and board Determination of roughness/smoothness (air leak methods) Part 4: Print-surf method Papier et carton Dtermination de la rugosit/du liss (mthodes du dbit dair) Partie 4: Mthode Prin

2、t-surf ISO 8791-4:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

3、In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found

4、 in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the a

5、ddress given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either

6、ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2007 All rights reservedISO 8791-4:2007(E) ISO 200

7、7 All rights reserved iii Contents Page Foreword iv 1 Scope 1 2 Normative references 1 3 Terms and definitions .1 4 Principle2 5 Apparatus .2 6 Sampling.6 7 Conditioning.6 8 Preparation of test pieces.6 9 Procedure .7 10 Calculation8 11 Precision.8 12 Test report 9 Annex A (normative) Calculation of

8、 roughness in micrometres10 Annex B (normative) Maintenance of Print-surf roughness testers 12 Annex C (normative) Calibration of variable-area flowmeters .14 Annex D (normative) Calibration of Print-surf instruments against ISO reference standards .16 Annex E (normative) Calibration of an impedance

9、 instrument for the purpose of assigning values to ISO reference standards.18 Bibliography 22 ISO 8791-4:2007(E) iv ISO 2007 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pr

10、eparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, i

11、n liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main tas

12、k of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attentio

13、n is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8791-4 was prepared by Technical Committee ISO/TC 6, Paper, board and pulps, Subcommittee SC 2, Test meth

14、ods and quality specifications for paper and board. This second edition cancels and replaces the first edition (ISO 8791-4:1992), which has been technically revised. This version of ISO 8791-4 differs from the previous (1992) version as follows: a definition of Print-surf compressibility has been ad

15、ded; a description of a modified backing holder for testing high-stiffness papers and board has been added; Annex D describing the calibration of Print-surf instruments has been revised and expanded; some minor editorial changes have been made. ISO 8791 consists of the following parts, under the gen

16、eral title Paper and board Determination of roughness/smoothness (air leak methods): Part 1: General method Part 2: Bendtsen method Part 3: Sheffield method Part 4: Print-surf method INTERNATIONAL STANDARD ISO 8791-4:2007(E) ISO 2007 All rights reserved 1 Paper and board Determination of roughness/s

17、moothness (air leak methods) Part 4: Print-surf method 1 Scope This part of ISO 8791 specifies a method for determining the roughness of paper and board using an apparatus which complies with the Print-surf method, as defined in this part of ISO 8791. It is applicable to all printing papers and boar

18、ds with which it is possible to form a substantially airtight seal against the guard lands of the measuring head. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refere

19、nces, the latest edition of the referenced document (including any amendments) applies. ISO 186, Paper and board Sampling to determine average quality ISO 187, Paper, board and pulps Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samp

20、les ISO 4094, Paper, board and pulps International calibration of testing apparatus Nomination and acceptance of standardizing and authorized laboratories 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 Print-surf roughness mean gap between a

21、 sheet of paper or board and a flat circular land pressed against it under specified conditions NOTE The mean gap is expressed as the cube root mean cube gap calculated as specified in Annex A. The Print- surf roughness is expressed directly as the average value of roughness, in micrometres. 3.2 Pri

22、nt-surf compressibility K percentage decrease in surface roughness when measurements are made consecutively at the two standard clamping pressures specified in this part of ISO 8791 ISO 8791-4:2007(E) 2 ISO 2007 All rights reserved4 Principle The test piece is placed between a circular flat metal se

23、nsing surface and a resilient backing, and inner and outer circular lands form a seal with the test piece. Under the influence of a pressure difference, air flows across the measuring land between the measuring land and the test piece. The rate of air flow is measured on a variable-area flowmeter, o

24、r the pressure difference across the measuring land is compared to the pressure difference across a known impedance. In both cases, the result is expressed as the air gap, in micrometres. 5 Apparatus 5.1 Print-surf tester (two types) 5.1.1 Print-surf tester, which operates according to one of the fo

25、llowing principles. 5.1.1.1 Variable-area flowmeter type, in which a standard pressure difference is created across the measuring land and the air-flow rate is measured on a variable-area flowmeter. The air-flow rate varies with roughness and the flow rate is converted to roughness, in micrometres.

26、The flow diagram for this type of instrument is shown in Figure 1. Key 1 incoming air 300 kPa to 600 kPa 2 filter 3 pressure-regulator valve 4 6,2 kPa or 19,6 kPa 5 on/off valve 6 flow indicator tubes 7 to atmosphere 8 sensing head and clamping device Figure 1 Flow diagram for variable-area flowmete

27、r type 5.1.1.2 Impedance type, in which the air from the controlled pressure source passes first through a fluidic impedance and then through the sensing head, after which it discharges to atmosphere. The pressure differences across the fluidic impedance and across the land are each measured by a tr

28、ansducer. These pressure differences vary with roughness and the signals are converted to roughness, in micrometres. The flow diagram for this type of instrument is shown in Figure 2. ISO 8791-4:2007(E) ISO 2007 All rights reserved 3Key 1 incoming air 300 kPa to 600 kPa 2 filter 3 pressure-regulator

29、 valve 4 19,6 kPa 5 fluidic impedance 6 pressure transducer 7 analog signal 8 to atmosphere 9 sensing head and clamping device Figure 2 Flow diagram for impedance instrument type 5.1.2 Procedures for maintaining these testers in good working order are given in Annex B. 5.2 Principal components of th

30、e system 5.2.1 Air supply, supplying clean air, free of oil and water droplets, at a steady pressure within the range 300 kPa to 600 kPa. 5.2.2 Sensing-head pressure regulator, allowing setting of the sensing-head differential pressure to 19,6 kPa 0,1 kPa or, on variable-area flowmeter instruments o

31、nly, to either 6,2 kPa 0,1 kPa or 19,6 kPa 0,1 kPa. 5.2.3 Sensing head, (see Figures 3 and 4), consisting of three concentric, annular lands composed of suitable material which have coplanar, polished surfaces. The centre or measuring land shall be 51,0 m 1,5 m wide and have an effective length of 9

32、8,0 mm 0,5 mm. The two guard lands shall each be at least 1 000 m wide at any point, and the radial distance between them at any point shall be 152 m 10 m. The measuring land shall be centred between them to within 10 m. The lands shall be mounted in an airtight mounting, constructed so that air can

33、 be passed into the gap between one guard land and the measuring land, and exhausted from the gap between the measuring land and the other guard land. The back of the mounting shall be flat and form a ground mating surface with the flat surface of a manifold fitted with air inlet and outlet ports. A

34、 spring-loaded protective collar may be fitted outside the guard lands. If such a protective collar is fitted, the force exerted by the loading spring shall be taken into account when setting the clamping pressure. NOTE In many instruments fitted with the protective collar, the force exerted by the

35、loading spring is 9,8 N. ISO 8791-4:2007(E) 4 ISO 2007 All rights reservedKey 1 measuring land 2 guard lands 3 passage connected to air supply 4 passage leading to flowmeters or atmosphere 5 recess vented to atmosphere Figure 3 Plan of the measuring and guard lands of the sensing head Key 1 paper 2

36、resilient backing 3 measuring land 4 regulated low-pressure air 5 to flowmeters or atmosphere Figure 4 The sensing head sectioned on two radii ISO 8791-4:2007(E) ISO 2007 All rights reserved 5 5.2.4 Backing holders, consisting of rigid metal discs of known mass, each recessed to accommodate a resili

37、ent backing at least 10 mm greater in diameter than the outside diameter of the outer guard land. The mass of both the resilient backing and the holder shall be allowed for in the initial adjustment of the clamping pressure. It has been observed that high-stiffness papers and boards can interact neg

38、atively with the flat metal backing holder and cause erroneously high roughness results. This problem can be solved by using a modified backing holder which relieves those areas of the backing holder not directly below the measuring land, as shown in Figure 5. Key 1 resilient backing 2 paper 3 regul

39、ated low-pressure air 4 measuring land 5 to flowmeters or atmosphere 6 new modified clamp platen showing machined cut-away Figure 5 The sensing head sectioned on two radii showing cut-away platen 5.2.5 Two resilient backings, of different types, which can be held in the recessed holders by means of

40、double-sided adhesive tape. 5.2.5.1 Soft backing, resilient, consisting of an offset printing blanket composed of a layer of synthetic rubber, at least 600 m thick, bonded to a fabric backing giving an overall thickness of 2 000 m 200 m. The apparent hardness of the complete backing shall be 83 IRHD

41、 6 IRHD (International Rubber Hardness Degrees). 5.2.5.2 Hard backing, resilient, usually made from a polyester film bonded at its periphery to cork, offset blanket or similar material. A small exhaust hole shall be provided to prevent air being trapped between the film and the backing. The apparent

42、 hardness of the assembly shall be 95 IRHD 2 IRHD. 5.2.6 Clamping mechanism, allowing clamping of the resilient backing at pressures of either 980 kPa 30 kPa or 1 960 kPa 30 kPa, the pressure being calculated from the total area of the measuring and guard lands. ISO 8791-4:2007(E) 6 ISO 2007 All rig

43、hts reservedNOTE 1 On some earlier instruments, these values may be displayed on the gauge as 10 kgf/cm 2and 20 kgf/cm 2 . Note that the spring loading in the protective collar (5.2.3) and the weight of the backing and its holder need to be taken into account. The rate of clamping shall be such that

44、 the pressure reaches 90 % of its final value in about 0,4 s, and 99 % of its final value in about 0,8 s. NOTE 2 A third pressure of 490 kPa (5 kgf/cm 2 ) is available on most instruments, but is not acceptable for use with this part of ISO 8791 because of a tendency for air to leak under the guard

45、lands. Variable-area flowmeter measurement systems shall have a pressure gauge fitted to the instrument to indicate the clamping pressure, which shall be adjustable. Impedance measurement systems shall have integrated pneumatic and electronic circuitry which automatically controls the clamping press

46、ure. In each case, the actual pressure achieved shall be verified as specified in B.3. 5.3 Measuring system 5.3.1 The air-flow rate shall be measured with either a set of variable-area flowmeters or by measuring the pressure drop across an impedance. 5.3.2 Variable-area flowmeter instruments shall b

47、e fitted with flowmeters which are graduated to show the “cube root mean cube gap” between the paper and the measuring land surface, in micrometres (see Annex A). The flowmeters shall be calibrated by the procedures outlined in either Annex C or D. 5.3.3 Impedance instruments measure air leakage by

48、means of fluidic impedance, a pressure transducer and a function generator. They display or print the roughness, in micrometres to the nearest 0,1 m, based on automatic measurement of pressure difference, over the range 0,6 m to 6,0 m. The value displayed shall be the value calculated after 3 s to 5

49、 s. This device shall be calibrated by the procedure described in Annex D. 6 Sampling If the tests are being made to evaluate a lot, the sample should be selected in accordance with ISO 186. If the tests are made on another type of sample, make sure that the test pieces taken are representative of the sample received. 7 Conditioning The sample shall be conditioned in accordance with ISO 187. 8 Preparation of test pieces Prepare the test pieces in the same atmo