ISO 7240-25-2010 Fire detection and fire alarm systems - Part 25 Components using radio transmission paths《火灾探测和报警系统 第25部分 用于无线电广播路径的组件》.pdf

《ISO 7240-25-2010 Fire detection and fire alarm systems - Part 25 Components using radio transmission paths《火灾探测和报警系统 第25部分 用于无线电广播路径的组件》.pdf》由会员分享，可在线阅读，更多相关《ISO 7240-25-2010 Fire detection and fire alarm systems - Part 25 Components using radio transmission paths《火灾探测和报警系统 第25部分 用于无线电广播路径的组件》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 7240-25:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 7240-25 First edition 2010-06-01 Fire detection and fire alarm systems Part 25: Components using radio transmission paths Systmes de dtection et dalarme dincendie Partie 25: Composants utilisant des voies de transmission radio

2、ISO 7240-25:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In dow

3、nloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in th

4、e General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address

5、 given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at

6、 the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedISO 7240-25:2010(E) ISO 2010 All

7、 rights reserved iiiContents Page Foreword iv Introductionvi 1 Scope1 2 Normative references1 3 Definitions and abbreviations 2 3.1 Definitions 2 3.2 Abbreviated terms .5 4 System requirements5 4.1 General .5 4.2 Radio frequency transmission paths 5 5 Components requirements.7 5.1 Compliance 7 5.2 G

8、eneral .7 5.3 Power supply equipment7 5.4 Environmental8 6 Marking.9 7 Data.9 7.1 General .9 7.2 Input/output devices .10 8 Tests .10 8.1 General requirements .10 8.2 System tests 11 8.3 Components tests .21 Annex A (normative) Test configuration by using radio-frequency-shielded test equipment .37

9、Annex B (normative) Immunity to site attenuation (path loss) 41 Annex C (informative) Data and calculation of the service life of the autonomous power source(s)42 Bibliography44 ISO 7240-25:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a

10、worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented

11、 on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are draft

12、ed in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Stan

13、dard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7240-25 was prepared

14、 by Technical Committee ISO/TC 21, Equipment for fire protection and fire fighting, Subcommittee SC 3, Fire detection and alarm systems. ISO 7240 consists of the following parts, under the general title Fire detection and alarm systems: Part 1: General and definitions Part 2: Control and indicating

15、equipment Part 3: Audible alarm devices Part 4: Power supply equipment Part 5: Point-type heat detectors Part 6: Carbon monoxide fire detectors using electro-chemical cells Part 7: Point-type smoke detectors using scattered light, transmitted light or ionization Part 8: Carbon monoxide fire detector

16、s using an electro-chemical cell in combination with a heat sensor Part 9: Test fires for fire detectors Technical Specification Part 10: Point-type flame detectors Part 11: Manual call points Part 12: Line type smoke detectors using a transmitted optical beam Part 13: Compatibility assessment of sy

17、stem components Part 14: Guidelines for drafting codes of practice for design, installation and use of fire detection and fire alarm systems in and around buildings Technical report ISO 7240-25:2010(E) ISO 2010 All rights reserved v Part 15: Point type fire detectors using scattered light, transmitt

18、ed light or ionization sensors in combination with a heat sensor Part 16: Sound system control and indicating equipment Part 17: Short-circuit isolators Part 18: Input/output devices Part 19: Design, installation, commissioning and service of sound systems for emergency purposes Part 20: Aspirating

19、smoke detectors Part 21: Routing equipment Part 22: Smoke-detection equipment for ducts Part 24: Sound-system loudspeakers Part 25: Components using radio transmission paths Part 27: Point-type fire detectors using a scattered-light, transmitted-light or ionization smoke sensor, an electrochemical-c

20、ell carbon-monoxide sensor and a heat sensor Part 28: Fire protection control equipment A part 23, dealing with visual alarm indicators, is under development. ISO 7240-25:2010(E) vi ISO 2010 All rights reservedIntroduction This part of ISO 7240 is based on European Standard EN 54-25, prepared by the

21、 European Committee for Standardization, CEN/TC 72, Fire detection and fire alarm systems. This part of ISO 7240 defines requirements and tests in addition to those in other parts of ISO 7240 that allow components of a fire detection and alarm system using radio transmission paths to operate with an

22、 integrity and stability similar to those of wire transmission paths. This part of ISO 7240 includes both equipment and system requirements because of the integral relationship between equipment that forms the system. Limitations to the use of radio components, such as capacity, can be specified in

23、national rules or guidelines. Technical aspects of the assessment of frequencies, bands and channels should be considered. INTERNATIONAL STANDARD ISO 7240-25:2010(E) ISO 2010 All rights reserved 1Fire detection and fire alarm systems Part 25: Components using radio transmission paths 1 Scope This pa

24、rt of ISO 7240 specifies requirements, test methods and performance criteria for components used in fire detection and alarm systems, installed in and around buildings, which use radio-frequency (r.f.) transmission paths. It specifies requirements for the assessment of conformance of the components

25、to the requirements of this part of ISO 7240. Where components work together and this requires knowledge of the system design, this part of ISO 7240 also specifies requirements for the system. When the fire detection and alarm system uses wired and r.f. transmission paths, the relevant parts of ISO

26、7240 apply together with this part of ISO 7240. Requirements relevant to wire transmission paths are superseded or modified by those included in this part of ISO 7240. This part of ISO 7240 does not restrict the intended use of radio spectrum, e.g. frequency, power output of devices; the allowed max

27、imum number of the components using r.f. transmission paths within the fire detection and alarm system or one wire transmission path and/or r.f. transmission path; the allowed maximum number of the components affected by loss of one wire transmission path and/or r.f. transmission path. 2 Normative r

28、eferences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7240-2, Fire detection and alarm sy

29、stems Part 2: Control and indicating equipment ISO 7240-4, Fire detection and alarm systems Part 4: Power supply equipment ISO 7240-5:2003, Fire detection and alarm systems Part 5: Point-type heat detectors ISO 7240-11, Fire detection and alarm systems Part 11: Manual call points ISO 7240-18, Fire d

30、etection and alarm systems Part 18: Input/output devices IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60068-2-1, Environmental testing Part 2-1: Tests Test A: Cold ISO 7240-25:2010(E) 2 ISO 2010 All rights reservedIEC 60068-2-2, Environmental testing Part 2-2: Tests Test B: Dr

31、y heat IEC 60068-2-6, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal) IEC 60068-2-27, Environmental testing Part 2-27: Tests Test Ea and guidance: Shock IEC 60068-2-30, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12 h + 12 h cycle) IEC 60068-2-42, Environ

32、mental testing Part 2-42: Tests Test Kc: Sulphur dioxide test for contacts and connections IEC 60068-2-78, Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 61620:1998, Insulating liquids Determination of the dielectric dissipation factor by measurement of the conductance

33、and capacitance Test method IEC 61672-1:2002, Electroacoustics Sound level meters Part 1: Specifications ITU-T O.153, Basic parameters for the measurement of error performance at bit rates below the primary rate EN 50130-4, Alarm systems Part 4: Electromagnetic compatibility Product family standard:

34、 Immunity requirements for components of fire, intruder and social alarm systems 3 Definitions and abbreviations For the purposes of this document, the terms, definitions and symbols given in ISO 7240-1 and the following apply. 3.1 Definitions 3.1.1 adjacent channel selectivity measure of the capabi

35、lity of the receiver to operate satisfactorily in the presence of an unwanted signal that differs in frequency from the wanted signal by an amount equal to the adjacent channel separation for which the equipment is intended 3.1.2 antenna element of a radio component of the fire detection and alarm s

36、ystem that allows coupling between the component and the media where r.f. waves are propagated 3.1.3 assigned band frequency band within which the equipment is authorized to operate 3.1.4 autonomous power source p.s.e. without any link to the public power supply or an equivalent system not rechargea

37、ble during operation and able by itself to power the supplied component EXAMPLE A primary battery. 3.1.5 base station transceiver in the system that communicates with a certain number of components ISO 7240-25:2010(E) ISO 2010 All rights reserved 33.1.6 blocking or desensitization measure of the cap

38、ability of the receiver to receive a wanted modulated signal without exceeding a given degradation due to the presence of an unwanted input signal at any frequencies other than those of the spurious responses or the adjacent channels or bands 3.1.7 collision simultaneous transmissions, from two or m

39、ore transmitters belonging to the same system, of sufficient signal strength to cause, by mutual interaction, corruption or obliteration of the information carried by the r.f. transmission path 3.1.8 compatibility capacity of a component of the system to operate with another component of this system

40、 within the limits specified by each component, within the specified limits given by the relevant parts of ISO 7240 if available or given by the manufacturer if not available, within specified configurations of the system 3.1.9 fire detection and alarm system group of components including a c.i.e. t

41、hat, when arranged in (a) specified configuration(s), is capable of detecting and indicating a fire, and giving signals for appropriate action 3.1.10 identification code part of a message used to identify a transmitting r.f. communication device belonging to the system 3.1.11 intermediate element de

42、vice connected to a transmission path of a fire detection and alarm system, used to receive and/or transmit signals necessary for the operation of the fire detection and alarm system NOTE An intermediate element meets the requirements of an input/output device in accordance with ISO 7240-18 but it i

43、s not restricted to electrical signals. 3.1.12 limited frequency range frequency of the local oscillator signal (f LO ) applied to the first mixer of the receiver plus or minus the sum of the intermediate frequencies (f I1 ,. f In ) and half of the switching range, r sw , of the receiver, as defined

44、 by the expression in Equation (1): sw sw II LO l LO =1 =1 22 nn jj jj rr ff + ff f uu (1) 3.1.13 manufacturer natural or legal person who places the equipment on the market under his own name NOTE Normally, the manufacturer designs and manufactures the product himself. A manufacturer can also desig

45、n, manufacture, assemble, pack, process or label the product as subcontractor or he assembles, packs, processes, or labels products as ready-made products. ISO 7240-25:2010(E) 4 ISO 2010 All rights reserved3.1.14 r.f. transmission path means of communication between at least two points, using r.f. w

46、ave propagation 3.1.15 radio part component or part of the component incorporating the receiver and/or transmitter NOTE The radio part can include a power supply, e.g. an autonomous power source. 3.1.16 receiver device that receives the r.f. energy corresponding to an r.f. transmission path NOTE The

47、 receiver can be incorporated in a component of the fire detection and alarm system. 3.1.17 r.f. interference r.f. transmission from a source other than a component of the fire detection and alarm system that can cause corruption or obliteration of wanted signals and that does not conform to the def

48、inition of collision or message substitution 3.1.18 service life period of useful life of an autonomous power source under specified conditions 3.1.19 site attenuation degradation of the r.f. signal due to either transmission path loss or a change in the environment of the fire detection and alarm s

49、ystem after its installation NOTE Site attenuation can be changed for example by installation or relocation of reflection or absorption materials. 3.1.20 special tool device not normally carried by the public (e.g. a key), normally provided by the manufacturer and that is used for opening the enclosure of the component to detach the antenna NOTE It is intended to deter unauthorized access to the antenna, while bei