ISO 6363-5-2012 Wrought aluminium and aluminium alloys - Cold-drawn rods bars tubes and wires - Part 5 Drawn square and hexagonal bars and wires - Tolerances on.pdf

《ISO 6363-5-2012 Wrought aluminium and aluminium alloys - Cold-drawn rods bars tubes and wires - Part 5 Drawn square and hexagonal bars and wires - Tolerances on.pdf》由会员分享，可在线阅读，更多相关《ISO 6363-5-2012 Wrought aluminium and aluminium alloys - Cold-drawn rods bars tubes and wires - Part 5 Drawn square and hexagonal bars and wires - Tolerances on.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2012 Wrought aluminium and aluminium alloys Cold-drawn rods/bars, tubes and wires Part 5: Drawn square and hexagonal bars and wires Tolerances on form and dimensions Aluminium et alliages daluminium corroys Barres, tubes et fils tirs froid Partie 5: Barres carres et hexagonales et fils tirs Tol

2、rances sur forme et dimensions INTERNATIONAL STANDARD ISO 6363-5 Second edition 2012-07-15 Reference number ISO 6363-5:2012(E) ISO 6363-5:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be

3、reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41

4、 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 6363-5:2012(E) ISO 2012 All rights reserved iii Contents Page Foreword iv 1 Scope 1 2 Normative references . 1 3 T erms and definitions . 1 4 Tolerances on form and dimensions 1 4.1 T olerances o

5、n width across flats 1 4.2 Fixed-length tolerances . 2 4.3 Squareness of cut ends . 3 4.4 Corner radii . 3 4.5 Form tolerances . 3 ISO 6363-5:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work

6、 of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmen

7、tal, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The ma

8、in task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. At

9、tention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6363-5 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee S

10、C 6, Wrought aluminium and aluminium alloys. This second edition cancels and replaces the first edition (ISO 6363-5:1992), which has been technically revised. ISO 6363 consists of the following parts, under the general title Wrought aluminium and aluminium alloys Cold-drawn rods/bars, tubes and wire

11、s: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Drawn round bars and wires Tolerances on form and dimensions (symmetric plus and minus tolerances on diameter) Part 4: Drawn rectangular bars and wires Tolerances on form and dimensions Part 5: Drawn sq

12、uare and hexagonal bars and wires Tolerances on form and dimensions Part 6: Drawn round tubes Tolerances on form and dimensions iv ISO 2012 All rights reserved INTERNATIONAL STANDARD ISO 6363-5:2012(E) Wrought aluminium and aluminium alloys Cold-drawn rods/ bars, tubes and wires Part 5: Drawn square

13、 and hexagonal bars and wires Tolerances on form and dimensions 1 Scope This part of ISO 6363 specifies the tolerances on form and dimensions of wrought aluminium and aluminium alloy drawn square and hexagonal bars and wires with widths across flats up to and including 100 mm. For wires, this part o

14、f ISO 6363 does not apply to electrical, welding and aeronautical purposes. For drawn bars, 4.1 to 4.5 apply, and only 4.1 applies to drawn wires. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition

15、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6363-1, Wrought aluminium and aluminium alloys Cold-drawn rods/bars, tubes and wires Part 1: Technical conditions for inspection and delivery 3 T erms and definitio ns For the

16、 purposes of this document, the terms and definitions given in ISO 6363-1 apply. 4 Tolerances on form and dimensions 4.1 T olerances on width across flats Tolerances on width across flats shall be in accordance with the plus and minus tolerances or the minus tolerance given in Table 1. The choice of

17、 tolerances depends on the agreement between the purchaser and the supplier. ISO 2012 All rights reserved 1 ISO 6363-5:2012(E) Ta b l e 1 T oleranc es on width a c ro s s flat s Dimensions in millimetres Width ac ro s s flat s s Plus and minus tolerances Maximum allowable deviation s 3 0,05 006 0 ,

18、3 s 6 0,05 008 0 , 6 s 10 0,05 009 0 , 10 s 18 0,06 011 0 , 18 s 30 0,08 013 0 , 30 s 50 0,13 016 0 , 50 s 65 0,16 020 0 , 65 s 80 0,20 030 0 , 80 s 100 0,30 035 0 , a) Square bar b) Hexagonal bar Key s width across flats F igure 1 Widths a c ro s s flat s 4.2 Fixed-length tolerances If fixed-length

19、 bars are ordered, their length tolerances shall be in accordance with Table 2. 2 ISO 2012 All rights reserved ISO 6363-5:2012(E) Table 2 Fixed-length tolerances Dimensions in millimetres Width across flat s s T olerances on fix ed lengths L 250 250 L 1 000 1 000 L 2 000 2 000 L 5 000 5 000 L s 30 0

20、 1 0 2 0 5 By agreement 30 s 50 0 2 0 3 0 4 0 6 50 s 100 0 25 , 0 4 0 5 0 7 4.3 Squareness of cut ends The squareness of cut ends shall be within half of the fixed length tolerance range (Table 2) for both fixed and random lengths. For example, for a fixed length tolerance of 0 2 mm, the squareness

21、of cut ends shall be within 1 mm. 4.4 Corner radii The corners of the bars shall be slightly rounded, but the corner radii shall not exceed the values specified in Table 3. Table 3 Maximum corner radii Dimensions in millimetres Width ac ro s s flat s s Maximum corner radii s 10 0,4 10 s 40 0,8 40 s

22、80 1,2 80 s 100 2,0 4.5 Form tolerances 4.5.1 General The maximum tolerance values specified in 4.5.2 and 4.5.3 apply to all tempers, except temper O. Form tolerances are measured by placing the bar on a horizontal plate under its own mass, as shown in Figures 2 and 3. 4.5.2 Straightness tolerances

23、The maximum allowable straightness tolerance, h 1,for the total length l 1 , shall be 2 mm per 1 000 mm of length (see Figure 2). In addition, h 2shall not exceed 0,6 mm for each section of 300 mm length (l 2 ). ISO 2012 All rights reserved 3 ISO 6363-5:2012(E) Key 1 base plate Figure 2 Measurement

24、of deviation from straightness 4.5.3 Convexity-concavity The convexity-concavity tolerance for square and hexagonal bars shall be included within the width across flats tolerances as given in Table 1. 4.5.4 Twist tolerances The maximum allowable twist tolerances, , shall be in accordance with Table

25、4. The twist shall be measured as shown in Figure 3. Table 4 Twist tolerances Dimensions in millimetres Width ac ro s s flat s s Twist tolerances Per 1 000 mm of length Over the total length L 5 000 5 000 L s 50 1,5 3 By agreement 50 s 100 2 5 Key 1 base plate s width across flats twist Figure 3 Mea

26、surement of twist 4 ISO 2012 All rights reserved ISO 6363-5:2012(E) 4.5.5 Squareness tolerances Squareness tolerances are specified in Table 5. The deviation from square, Z, shall be measured as shown in Figure 4. Table 5 Squareness tolerances Dimensions in millimetres Width ac ro s s flat s s Maximum deviation from square Z 2 s 100 0,005 s Key Z deviation from square Figure 4 Measurement of deviation from square ISO 2012 All rights reserved 5ISO 6363-5:2012(E) ISO 2012 All rights reserved ICS 77.150.10 Price based on 5 pages