ISO 6199-2005 Micrographics - Microfilming of documents on 16 mm and 35 mm silver-gelatin type microfilm - Operating procedures《缩微摄影技术 在16mm和35mm银明胶型缩微胶片上拍摄文献 操.pdf

《ISO 6199-2005 Micrographics - Microfilming of documents on 16 mm and 35 mm silver-gelatin type microfilm - Operating procedures《缩微摄影技术 在16mm和35mm银明胶型缩微胶片上拍摄文献 操.pdf》由会员分享，可在线阅读，更多相关《ISO 6199-2005 Micrographics - Microfilming of documents on 16 mm and 35 mm silver-gelatin type microfilm - Operating procedures《缩微摄影技术 在16mm和35mm银明胶型缩微胶片上拍摄文献 操.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 6199:2005(E) ISO 2005INTERNATIONAL STANDARD ISO 6199 Second edition 2005-06-15 Micrographics Microfilming of documents on 16 mm and 35 mm silver- gelatin type microfilm Operating procedures Micrographie Microfilmage des documents sur microfilms glatino- argentiques de 16 mm et

2、35 mm Modes opratoires ISO 6199:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing

3、 the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF fil

4、e can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secret

5、ariat at the address given below. ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the addr

6、ess below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2005 All rights reservedISO 6199:2005(E) ISO 2005 All rights rese

7、rved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Preparation of documents . 2 5 Conditions of microfilming 2 5.1 Raw-stock microfilm. 2 5.2 Formats and orientation. 2 5.3 Roll film coding . 5 5.4 Frame numbering 5 5.5 Placement 5 5.6 Inter-image

8、gap . 5 5.7 Edge marker 5 5.8 Reduction ratio 5 5.9 Document dimensions . 6 6 Microfilming procedures 9 6.1 Documents recorded on more than one roll of film 9 6.2 Leader and trailer 9 7 Filming sequence 9 7.1 Targets . 9 7.2 Archival test area 10 7.3 Retakes 10 7.4 Targets . 10 8 Scanning microfilm.

9、 12 8.1 Cameras used for producing scanning microfilm. 12 8.2 Frame numbering 12 8.3 Placement 12 8.4 Edge detection 12 8.5 Targets . 12 8.6 Image density 13 8.7 Skew. 13 8.8 Resolution . 13 9 Splices . 13 10 Document placement on the camera baseboard. 13 11 Winding 13 12 Quality control. 14 13 Lega

10、l Admissibility . 14 Annex A (informative) Preparation of documents 15 Annex B (informative) Resolution. 17 Bibliography . 19 ISO 6199:2005(E) iv ISO 2005 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO

11、member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern

12、mental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Di

13、rectives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member b

14、odies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6199 was prepared by Technical Committee ISO/TC 171, Document management ap

15、plications, Subcommittee SC 2, Application issues. This second edition cancels and replaces the first edition (ISO 6199:1991), which has been technically revised. INTERNATIONAL STANDARD ISO 6199:2005(E) ISO 2005 All rights reserved 1 Micrographics Microfilming of documents on 16 mm and 35 mm silver-

16、gelatin type microfilm Operating procedures 1 Scope This International Standard specifies procedures that enable a camera operator to produce microfilm of appropriate quality of presentation and legibility, capable of yielding scanned images of acceptable quality. This International Standard specifi

17、es methods for microfilming documents on 16 mm and 35 mm silver-gelatin microfilm, including orientation of images on microfilm, use of non-image areas and information required to facilitate identification of the microfilm. This International Standard applies to microfilming using rotary and planeta

18、ry cameras. This International Standard does not apply to the filming of technical drawings, maps and plans and newspapers, for which specific International Standards exist 1-3. 2 Normative references The following referenced documents are indispensable for the application of this document. For date

19、d references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3334: 1) , Micrographics ISO resolution test chart No. 2 Description and use ISO 6148:2001, Photography Micrographic films, spools and cores Dim

20、ensions ISO 6196 (parts 1 to 8 and 10), Micrographics Vocabulary ISO 6200:1999, Micrographics First generation silver-gelatin microforms of source documents Density specifications and method of measurement ISO 9878:1990, Micrographics Graphical symbols for use in microfilming ISO/TR 10200:1990, Lega

21、l admissibility of microforms ISO 10550:1994, Micrographics Planetary camera systems Test target for checking performance ISO 10594, Micrographics Rotary camera systems Test target for checking performance ISO 11962:2002, Micrographics Image mark (blip) used with 16 mm and 35 mm roll microfilm ISO 1

22、8906:2000, Imaging materials Photographic films Specifications for safety film 1) To be published. (Revision of ISO 3334:1989) ISO 6199:2005(E) 2 ISO 2005 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6196 and the following apply

23、. 3.1 inter-image gap inter-frame gap distance, measured along the long edge of a roll microfilm, between the trailing edge of one microimage and the leading edge of the following microimage 3.2 scanning microfilm microfilm intended to be used for scanner input 4 Preparation of documents Documents t

24、o be microfilmed shall be examined carefully, defects remedied where appropriate, foreign bodies (e.g. fasteners) removed and pages arranged in the required order. Documents to be microfilmed shall be examined to ensure that their dimensions are within those acceptable to the microfilming system. Ap

25、propriate targets shall be added to each batch of documents during the preparation stage. Annex A gives more details on the preparation of documents prior to microfilming. 5 Conditions of microfilming 5.1 Raw-stock microfilm Raw-stock microfilm shall comply with the requirements of ISO 6148 and ISO

26、18906. 5.2 Formats and orientation 5.2.1 Formats The formats commonly used in roll microfilm are shown in Figure 1. The dimensions for the placement of the microimages on the film are listed in Table 1. Table 1 Dimensions of frames for unperforated film without document marks (see Figure 1) Values i

27、n millimetres Dimension Measure 16 mm film 35 mm film a max. image width 14,92 33,00 ac min. inter-image gap 1,00 2,00 d min. side margin 0,50 0,97 e min. side margin 0,50 0,97 f min. bcentre margin 0,50 0,97 NOTE Film width (e.g. a + 2d) shall be in accordance with ISO 6148. Image areas are smaller

28、.aFor some applications, this figure may change in accordance with the relevant International Standard. bFor all formats except simplex. ISO 6199:2005(E) ISO 2005 All rights reserved 3Alternate orientation for documents with right to left scripts Preferred orientation for documents with horizontal a

29、nd right to left scripts Figure 1 Roll microfilm formats ISO 6199:2005(E) 4 ISO 2005 All rights reservedNOTE 1 On the duplex format, the image orientation of one row (front) is controlled by the orientation of the text on the original page, and the image orientation of the opposite row (back) is con

30、trolled by the image orientation of the above mentioned row. NOTE 2 The duo duplex format is used primarily in banking applications. aFront and back of first document bAscending order cFirst (or last) document dAscending (or descending) order Figure 1 (continued) ISO 6199:2005(E) ISO 2005 All rights

31、 reserved 5 5.2.2 Orientation Where microimages are recorded in simplex format, horizontal mode (comic), orientations 1B and 2B of Figure 1 shall be used. Where simplex format, vertical mode (cine) is used, the microimages should be oriented as shown in 1A and 2A of Figure 1. The orientation of micr

32、oimages for filming in duplex, duo and combination duo-duplex formats is also shown in Figure 1. 5.3 Roll film coding Microimages may be coded so that individual microimages or series of microimages can be easily located. Examples of coding systems are specified in ISO 11962. 5.4 Frame numbering Whe

33、re frame numbers are used, they shall not appear within the microimage frame area. They may appear towards either edge of the microfilm, or within the inter-image gap, offset towards the top or bottom of the gap. Frame numbers shall not exceed 2 mm in height, measured on the microfilm. The positioni

34、ng of the frame numbers shall remain consistent within a roll of microfilm. See also 8.2. 5.5 Placement Microimages shall be centrally placed across the width of the frame area, with at least 30 % of each microimage in each half of the useable width of the microfilm. See also 8.3. 5.6 Inter-image ga

35、p The inter-image gap shall be as specified in Table 1. NOTE When using scanning microfilm, this inter-image gap is crucial to the detection of the image edge (see 8.4). 5.7 Edge marker This subclause applies to microfilming using planetary cameras only. Where the leading edge of a document to be mi

36、crofilmed is so irregular that there is no segment of this edge that can be said to define the position of the edge unambiguously, a matt white bar of minimum width 3 mm shall be placed on the camera baseboard, parallel to the leading edge of the microimage area, and just touching the leading edge o

37、f the document. The length of the bar shall be sufficient to extend across the whole width of the microimage area. 5.8 Reduction ratio The reduction ratio and orientation selected should allow the smallest alphanumeric characters to be legible in a distribution copy projected on a reader screen and

38、on a hard copy made from a distribution copy. The reduction ratio to be used shall be determined by the size of the characters, the quality of the originals, the quality of the camera-film system, and the size of the documents to be microfilmed. Where possible, horizontal mode should be used. ISO 61

39、99:2005(E) 6 ISO 2005 All rights reserved5.9 Document dimensions 5.9.1 General The maximum height or width of a microimage that can be recorded on the usable width of the film is indicated in Table 1 and Figure 1 for uncoded film and Figure 2 for coded film. NOTE The maximum height or width of the d

40、ocument depends on the film format, the reduction ratio and the type of camera (rotary or planetary) to be used. 5.9.2 Simplex format using rotary cameras The side of a microimage which is parallel to the length of the film may be of any length. Table 2 lists two of the most commonly used reduction

41、ratios for the simplex format of uncoded film from 16 mm rotary cameras. If a microimage is close to the indicated recordable size, a higher reduction ratio shall be used to reduce the possibility of information loss caused by skewing of the document while it is being filmed. NOTE The maximum dimens

42、ions of a document that can be filmed are determined by the width of the throat of the document feeder. Table 2 16 mm rotary microfilm camera Simplex format for uncoded film Values in millimetres Nominal reduction ratio Maximum dimension of document side perpendicular to the long axis of the film 1:

43、20 1:24 298 357 Dimensions in millimetres aChannel reserved for document mark. Figure 2 Channels provided for document marks (blips) and optical code format ISO 6199:2005(E) ISO 2005 All rights reserved 7 5.9.3 Simplex format using planetary cameras Simplex format is also used with planetary cameras

44、 that can have variable (or a set of fixed) reductions and a variable frame pitch. Table 3 lists the maximum dimensions of documents usable with various reduction ratios. For microfilming using fixed frame-pitch cameras, see Table 4 and Figure 3. NOTE To allow for positioning errors, the actual dime

45、nsions of the documents should be less than those indicated. For 35 mm film intended for insertion in A6 jackets as strips of three frames, the maximum frame pitch shall be 47,5 mm. Appropriate reduction ratio changes may be required to accommodate the shorter frame advance. Table 3 Planetary roll m

46、icrofilm camera with adjustable frame pitch Maximum dimensions of documents Values in millimetres Maximum dimensions of documents 16 mm microfilm 35 mm microfilm Reduction ratio aLength Width Length Width 1:6 1:8 1:10 1:12 1:14 1:15 1:16 1:18 1:20 1:21 1:22 1:24 1:26 1:27 1:28 1:29 1:30 1:32 1:34 1:

47、36 229 305 381 457 533 572 610 686 762 800 838 914 991 1 029 1 067 1 105 1 143 1 219 1 295 1 372 90 120 150 180 210 225 240 270 300 315 330 360 390 405 420 435 450 480 510 540 267 356 444 533 622 667 711 800 889 933 978 1 067 1 156 1 200 1 245 1 289 1 334 1 422 1 511 1 600 190 254 318 381 444 476 50

48、8 572 635 667 698 762 826 857 889 921 952 1 016 1 080 1 143 aCaution, actual reduction ratios used in practice may be different to those indicated in this table. Relevant measurements can be calculated by applying the reduction ratio to the image frame dimensions. ISO 6199:2005(E) 8 ISO 2005 All rig

49、hts reservedTable 4 Planetary roll film camera with fixed film advance (see Figure 3) Values in millimetres 35 mm microfilm Dimensions Frame (a b) 00 0,5 0,5 33 45 Frame pitch (t) 0 1,2 52 Figure 3 Frame and frame pitch 5.9.4 Simplex format coding Simplex format is also used with microfilm that is coded along the edge with a document mark or a photo- optical code. Coded microfilm is produced in both planetary and rotary cameras at a fixed reduction ratio. The manufactur