ISO 6043-1985 Shipbuilding and marine structures Eye and fork assemblies under tension load Main dimensions《造船及海上结构物 受拉伸作用的眼板叉头 主要尺寸》.pdf

《ISO 6043-1985 Shipbuilding and marine structures Eye and fork assemblies under tension load Main dimensions《造船及海上结构物 受拉伸作用的眼板叉头 主要尺寸》.pdf》由会员分享，可在线阅读，更多相关《ISO 6043-1985 Shipbuilding and marine structures Eye and fork assemblies under tension load Main dimensions《造船及海上结构物 受拉伸作用的眼板叉头 主要尺寸》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、International Standard INTERNATIONAL ORGANIZATION FOR STANDARDIZATION.MEXfiYHAPOflHAR OPTAHM3AMfl fl0 CTAHAPTM3AWl.ORGANISATION INTERNATIONALE DE NORMALISATION Shipbuilding and marine structures - Eye and fork assemblies under tension load - Main dimensions Cons truc tion na vale et s truc tures mar

2、itimes - Assemblages a0i.f et chape soumis 2 un effort de traction - Dimensions principales First edition - 1985-12-15 UDC 621.885.9 : 629.12 Ref. No. ISO 6043-1985 (E) Descriptors : shipbuilding, Iifting equipment, joints, clevises, pins (mechanics), dimensions, materials, designation. Price based

3、on 3 pages Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bedies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject fo

4、r which a technical committee has been established has the right to be represented on that committee. International organizations, govern- mental and non-governmental, in liaison with ISO, also take part in the work. Draft International Standards adopted by the technical committees are circulated to

5、 the member bodies for approval before their acceptance as International Standards by the ISO Council. They are approved in accordance with ISO procedures requiring at least 75 % approval by the member bodies voting. International Standard ISO 6043 was prepared by Technical Committee ISO/TC 8, Shipb

6、uilding and marine structures. Users should note that all International Standards undergo revision from time to time and that any reference made herein to any other International Standard implies its latest edition, unless otherwise stated. 0 International Organkation for Standardkation, 1985 Printe

7、d in Switzerland INTERNATIONAL STANDARD ISO 6043-1985 (E) Shipbuilding and marine structures - Eye and fork assemblies under tension load - Main dimensions 1 Scope and field of application 1.1 This International Standard lays down the main dimen- sions for interchangeability and the materials for ey

8、es, forks and associated bolts or pins for components subject to tension load. 1.2 Eyes, forks and bolts or pins with dimensions according to this International Standard are primarily intended for use on the components of ships cargo handling appliances which are subject to tension loads only (for i

9、nstance, round hole eyeplates, sheave block head fittings, block holders, trunnion pieces for span bearing, turnbuckles). 1.3 This International Standard is not applicable to com- ponents subject to compressive thrust or torsional loads (for instance fork-type derrick heel fittings which connect wit

10、h gooseneck Pins). 4 Nominal size The nominal size designation of an eye and fork assembly is a numerical value without unit for reference purposes; it is derived from the permissible load in kilonewtons. 5 Dimensions and tolerantes 5.1 Main dimensions The dimension of eye and fork assemblies shall

11、be in accord- ante with the figure and the table. NOTE - The type of bolt or pin to be used and its securing are left to national regulations. 5.2 Tolerantes Dimensional tolerantes shall correspond to the Standard tolerante grade IT 14 given in ISO 286. 2 References 6 Material ISO 286, ISO System of

12、 limits and fits. 1 ) 6.1 Eyes and forks ISO 630, Structural steels. ISO/R 68311, Heat-treated steels, alloy steels and free-cutting steels - Part 1: Quenched and tem,oered unalo yed steels. ISO 8147, Shipbuilding and marine structures - Derrick rigs and component parts - Vocabulary. 2) 3 Definition

13、s For the purposes of this International Standard, the definitions given in ISO 8147 apply. Eyes and forks shall be made of steel to ISO 630, grade Fe 360 (as minimum quality). 6.2 Bolts or pins Bolts or pins shall be made of steel to ISO 630, grade Fe 430 (as minimum quality). . 6.3 Higher quality

14、If the use of heat-treated quenched steel is required, then the material shall comply with ISO/R 683/1. 1) At present at the Stage of draft. (Revision of ISO/R 286-1962.) 2) At present at the Stage of draft. ISO 6043-1985 (El Fork (6) F Tension load s -. Tension load b 3 - NOTE - The bolt or pin is

15、not shown in the sectional drawing. Bolt or pin Figure - Shape of eyes and forks 2 ISO 6043-1985 (El Table - Nominal sizes and main dimensions Dimensions in millimetres Nominal size Permissible load kN hl 0,4 4 05 6,3 1 IO V 16 2 20 2,5 25 3 4 5 31,5 40 50 6 8 IO 63 80 100 - 125 160 200 - 250 315 40

16、0 IO 12 16 - 20 22 25 - 28 30 35 - 40 45 50 12 5 16 6 19 8 23 11 26 12 29 13 32 14 35 15 39 18 45 20 49 23 58 26 12 16 20 55 64 28 60 70 30 65 74 33 25 32 40 70 80 35 80 90 40 90 100 45 50 500 100 63 630 110 80 800 125 110 120 140 50 55 65 100 1 000 140 156 70 125 1 250 160 176 80 160 1 600 180 200

17、90 200 2 000 200 220 100 250 2 500 220 240 110 dl d2 d3 IO 11 IO,5 12 13,5 13 16 17,5 17 20 22 21 22 24 23 24 26 25 27 30 28 30 33 31 36 39 37 39 42 40 45 48 46 48 52 50 52 56 54 60 66 62 68 74 70 72 78 74 80 86 82 90 96 93 100 107 104 110 117 114 125 132 129 140 147 144 160 168 165 180 188 185 200

18、208 205 220 230 225 rl 15 18 23 28 31 34 - 36 39 46 51 56 63 70 75 80 87 97 111 230 250 22,5 25 27,5 5 6 6 - 6 6 8 30 32,5 37,5 42,5 47,5 55 8 8 8 60 65 70 75 85 95 12 12 16 16 16 20 105 115 135 148 168 190 210 230 NOTE - The values of dimensions dz and d3 are in agreement with ISO 273, Fasteners -

19、Clearance holes for bolts and screws. 7 Designation 7.2 Examples For reference purposes only (e.g. in technical drawings), but not for ordering purposes, the eyes and forks and the assembled connection with bolt or pin shall be designated as follows. 7.2.1 For an eye An eye in accordance with this I

20、nternational Standard, code letter A, of nominal size 10 is designated as follows: Eye ISO 6043 - A IO 7.1 Elements for designation 7.2.2 For a fork The following elements shall be given in the Order indicated: a) denomination: eye (or fork or connection); b) number of this International Standard: I

21、SO 6043; A fork in accordance with this International Standard, code letter B, of nominal size 10 is designated as follows: Fork ISO 6043 - B 10 7.2.3 For a connection c) code letter: A (for eye), B (for fork), C (for connection) ; d) nominal size (in accordance with the table). A connection of eye and fork with bolt or pin in accordance with this International Standard, code letter C, of nominal size 10 is designated as follows: Connection ISO 6043 - C 10 3 This page intentianally left blank This page intentionally leff blank This page intentionally left blank