ISO 6042-2015 Ships and marine technology - Weathertight single-leaf steel doors《船舶与海上技术 钢质单扇风雨密门》.pdf

《ISO 6042-2015 Ships and marine technology - Weathertight single-leaf steel doors《船舶与海上技术 钢质单扇风雨密门》.pdf》由会员分享，可在线阅读，更多相关《ISO 6042-2015 Ships and marine technology - Weathertight single-leaf steel doors《船舶与海上技术 钢质单扇风雨密门》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2015 Ships and marine technology Weathertight single-leaf steel doors Navires et technologie maritime Portes en acier un seul battant, tanches aux intempries INTERNATIONAL STANDARD ISO 6042 Third edition 2015-09-01 Reference number ISO 6042:2015(E) ISO 6042:2015(E)ii ISO 2015 All rights reserve

2、d COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intra

3、net, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.or

4、g www.iso.org ISO 6042:2015(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 Doors, door frames, door plates, and accessories . 1 3.1 Opening direction . 1 3.2 Door types . 2 3.3 Door frames (see Figure 3) . 4 3.4 Door plates . 5 3.5 Fittings . 7 3.5.1 Location of door clips and hinges 7 3.5.2 W

5、edges (see Figure 6) . 8 3.5.3 Hinges (see Figure 7) . 9 3.5.4 Door seal 10 4 Materials 11 5 Quality of manufacture .12 6 Testing of weather tightness .12 7 Designation .12 ISO 2015 All rights reserved iii Contents Page ISO 6042:2015(E) Foreword ISO (the International Organization for Standardizatio

6、n) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be rep

7、resented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to de

8、velop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the I

9、SO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified durin

10、g the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the mea

11、ning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information. The committee responsible for this document is ISO/TC 8

12、, Ships and marine technology, Subcommittee SC 8, Ship design. This third edition cancels and replaces the second edition (ISO 6042:1998), which has been technically revised.iv ISO 2015 All rights reserved INTERNATIONAL ST ANDARD ISO 6042:2015(E) Ships and marine technology Weathertight single-leaf

13、steel doors 1 Scope This International Standard specifies the main dimensions, materials, quality and conditions of manufacture for weathertight single-leaf steel doors for application on board ships, in order to ensure interchangeability of the steel doors. The remaining dimensions, welding, and ot

14、her details are left to the manufacturer. These doors generally conform to the requirements of the International Convention on Load Lines 1966 (ICLL66). The possibility for application of the doors to position 1 and position 2 has to be considered for each situation and, where necessary, the doors s

15、hall be provided with additional stiffening (see also Table 1). Users of this International Standard should note that while observing the requirements of this International Standard they should, at the same time, ensure compliance with such statutory requirements, rules, and regulations as may be ap

16、plicable to the individual ship concerned. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of t

17、he referenced document (including any amendments) applies. ISO 3796, Ships and marine technology Clear openings for external single-leaf doors 3 Doors, door frames, door plates, and accessories 3.1 Opening direction For the definitions of left-hand door and right-hand door, see Figure 1. Doors in ac

18、cordance with this International Standard can be used for both opening directions (left- hand or right-hand) before they are installed in bulkhead plates. 11 L R Key 1 hinge L left-hand R right-hand Figure 1 Opening direction ISO 2015 All rights reserved 1 ISO 6042:2015(E) 3.2 Door types The types o

19、f doors shall conform to the detail of Table 1 and Figure 2. The nominal sizes (height L width B) given in Table 2 are in accordance with ISO 3796. The assignment of door types to door frames and door plates is shown in Table 3. Table 1 Types of doors Types Definition AB Multi-handles door using ang

20、le bar frame FB Multi-handles door using flat bar frame (radius of 31 mm) FBR Multi-handles door using flat bar frame (radius of 100 mm) ABL Single-handle with interlock clips door using angle bar frame FBL Single-handle with interlock clips door using flat bar frame (radius of 31 mm) FBRL Single-ha

21、ndle with interlock clips door using flat bar frame (radius of 100 mm) Dimensions in millimetres 1 1 B L A A L B B B A A 1 B B 1 B B L B B B 1 1 L B 1 1 L B 1 1 L B 1 AB FB FBR ABL FBLF BRL 12 ISO 2015 All rights reserved ISO 6042:2015(E) 18 a 22 a a 22 a 18 B-B A-A 9 8 6 7 10 2 3 4 5 5 4 3 2 C-C Ke

22、y 1 clear opening 7 sleeve 2 bulkhead plate 8 inside handle 3 door frame 9 interlock 4 door seal 10 inclined wedge 5 door plate 11 total thickness of door 6 door handle a When the seal is compressed by 2 mm, door plate shall be positioned centrally within the frame. NOTE 1 Six clips and single-handl

23、e design with interlock clips. NOTE 2 For four clips design and eight clips design, see 3.5.1 and Figure 5. Figure 2 Types of doors ISO 2015 All rights reserved 3 ISO 6042:2015(E) Table 2 Doors, nominal sizes, and application Dimensions in millimetres Door Nominal size L B Application in accordance

24、with ICLL66 in position (s) 1 200 600 1 and 2 1 400 600 1 400 750 1 400 900 1 500 600 2 only 1 500 750 1 500 900 1 600 600 1 600 750 1 600 900 1 700 600 1 700 750 1 700 900 1 800 600 1 800 750 1 800 900 Table 3 Assignment of door type to door frames and door plates Door type Associated type of door

25、frame (according to 3.3) door plate (according to 3.4) AB ABF SP FB FBF SP FBR FBRF RP ABL ABF SP FBL FBF SP FBRL FBRF RP 3.3 Door frames (see Figure 3) In order to prevent damage to the door seal, the edges of the upper part of the door frame shall be rounded or chamfered. The dimensions of door fr

26、ames are given in Table 4.4 ISO 2015 All rights reserved ISO 6042:2015(E) R ABF FBF/FBRF L B B L NOTE Angle bar 75 50 7 a ; Flat bar 70 8 a . aOther sections may be used, provided that the interchangeability of dimensions is maintained. Figure 3 Types of door frames Table 4 Dimensions of door frames

27、 Dimensions in millimetres Nominal size L 0 -2 B 0 -2 R for type FBF FBRF 1 200 600 1 200 600 31 1 100 1,5 1 400 600 1 400 600 1 400 750 1 400 750 1 400 900 1 400 900 1 500 600 1 500 600 1 500 750 1 500 750 1 500 900 1 500 900 1 600 600 1 600 600 1 600 750 1 600 750 1 600 900 1 600 900 1 700 600 1 7

28、00 600 1 700 750 1 700 750 1 700 900 1 700 900 1 800 600 1 800 600 1 800 750 1 800 750 1 800 900 1 800 900 3.4 Door plates The door-seal retaining bar can be placed in inclined or vertical position, as indicated in Figure 4. The dimensions (height, L and width, B) of door plates are given in Table 5

29、. ISO 2015 All rights reserved 5 ISO 6042:2015(E) Dimensions in millimetres Key L 1 , B 1 inside dimension of door plate Figure 4 Types of door plates Table 5 Dimensions of door plates Dimensions in millimetres Nominal size L 12 B 12 1 200 600 1 244 644 1 400 600 1 444 644 1 400 750 1 444 794 1 400

30、900 1 444 944 1 500 600 1 544 644 1 500 750 1 544 794 1 500 900 1 544 944 1 600 600 1 644 644 1 600 750 1 644 794 1 600 900 1 644 9446 ISO 2015 All rights reserved ISO 6042:2015(E) Nominal size L 12 B 12 1 700 600 1 744 644 1 700 750 1 744 794 1 700 900 1 744 944 1 800 600 1 844 644 1 800 750 1 844

31、794 1 800 900 1 844 944 3.5 Fittings 3.5.1 Location of door clips and hinges Regarding all values given in Figure 5, for the centre lines of door clips and hinges, refer to the clear opening (see Figure 2). Table 6 shows the number of clips for each nominal size. Dimensions in millimetres 350 B 350

32、H B 350 250 L 250 L 250 B 250 a) Eight clips design b) Six clips design c) Four clips design Key H/L height/length of the door Figure 5 Location of fittingsTable 5 (continued) ISO 2015 All rights reserved 7 ISO 6042:2015(E) Table 6 Number of clips Dimensions in millimetres Nominal size Number of cli

33、ps 1 200 600 6 1 400 600 6 1 400 750 6 1 400 900 6 1 500 600 4 1 500 750 4 1 500 900 4 1 600 600 4 1 600 750 4 1 600 900 6 1 700 600 6 1 700 750 6 1 700 900 8 1 800 600 6 1 800 750 6 1 800 900 8 3.5.2 Wedges (see Figure 6) Wedges shall be arranged on the frames to align with the centre lines of each

34、 clip. A slope of 1:12 is recommended. The direction of the slope of the wedge shall correspond to the required closing direction of the clips, as shown in Figure 2. For a correct fit of the frame edge with the packing material, a final adjustment of clip wedges may be added.8 ISO 2015 All rights re

35、served ISO 6042:2015(E) Dimensions in millimetres Key 1 maximum offset of wedge from clear opening 2 door frame Type ABF 3 clear opening 4 centre line of clip 5 door frame Type FBF or FBRF Figure 6 Location of fittings 3.5.3 Hinges (see Figure 7) Two hinges shall be fitted to each door. Each hinge s

36、hall be provided with an oval eye hole, in order to allow clips to compress the door seal uniformly. ISO 2015 All rights reserved 9 ISO 6042:2015(E) Dimensions in millimetres R20 19 76 75 22 12 54 120 8 Figure 7 Hinges 3.5.4 Door seal The door seal shall have a cross-section as shown in Figure 8. In

37、 order to increase the elasticity, a hole may be added at the longitudinal centre line of the door seal. The size of the chamfer will depend on the radius of the door panel. The door seal shall be fitted to the door as indicated in Figure 7 and shall be secured by a retaining bar. The seal shall be

38、bonded to the door plate by an adhesive suitable for marine conditions. It shall be ensured, by a depth stop positioned on the centre line of each clip, that the door seal cannot be compressed to less than 16 mm. Dimensions in millimetres 20 12 45 45 Figure 8 Door seal cross-section10 ISO 2015 All r

39、ights reserved ISO 6042:2015(E) Key 1 key 5 sealing strip (material is the same as 3.5.4) 2 bolt and nut 6 butterfly nut 3 steel bush 7 bulkhead 4 door plate Figure 9 Security device 4 Materials The door plates and frames shall be manufactured from weldable steel of 235 N/mm 2minimum yield strength

40、or equivalent shipbuilding-quality steel. The door-seal retaining bars, clips, wedges, hinges, and lugs shall be manufactured from weldable mild steel of 340 N/mm 2minimum tensile strength. The hinge pin shall be manufactured from corrosion-resistant materials of 350 N/mm 2minimum tensile strength.

41、The quality of the resilient sealing material forming the door seal shall be satisfactory for service under marine conditions and shall provide effective and lasting sealing and resealing properties when the door is tightened under normal conditions. ISO 2015 All rights reserved 11 ISO 6042:2015(E)

42、5 Quality of manufacture All door plates and frames shall be free from distortion. The door plates, frames, and fittings shall be suitably treated to remove scale and surface deposits and shall be given a priming coat of paint, where appropriate, to inhibit subsequent corrosion. The door plates, fra

43、mes, clips, and other ancillary fittings shall be free from exposed rough edges likely to cause injury to persons. For door frames, see also 3.3. Upon assembly of the completed door and frame, the manufacturer shall ensure that there is correct fit of the frame edge with the packing material and con

44、tinuous contact between the two components when the door is closed (see also 3.5.2). 6 Testing of weather tightness The completed door, when installed on board ship, shall be closed and secured in a normal manner, and then subjected to a test (hose test or equivalent test) carried out to the satisfa

45、ction of the representative of the regulatory body concerned. 7 Designation Doors conforming to this International Standard shall be designated by the following indications, in the order given: a) denomination: Door; b) number of this International Standard: ISO 6042; c) type (code letter), as speci

46、fied in 3.2; d) nominal size, as specified in Table 1. EXAMPLE Designation of a weathertight single-leaf steel door in accordance with this International Standard, Type FBR, with the nominal size 1 400 mm 750 mm:Door ISO 6042-FBR-1 400 750 NOTE This designation is valid for non-installed doors only (see also 3.1).12 ISO 2015 All rights reserved ISO 6042:2015(E) ISO 2015 All rights reserved ICS 47.020.10 Price based on 12 pages