ISO 4892-4-2013 Plastics - Methods of exposure to laboratory light sources - Part 4 Open-flame carbon-arc lamps《塑料 实验室光源辐照方法 第4部分 明火炭弧灯》.pdf

《ISO 4892-4-2013 Plastics - Methods of exposure to laboratory light sources - Part 4 Open-flame carbon-arc lamps《塑料 实验室光源辐照方法 第4部分 明火炭弧灯》.pdf》由会员分享，可在线阅读，更多相关《ISO 4892-4-2013 Plastics - Methods of exposure to laboratory light sources - Part 4 Open-flame carbon-arc lamps《塑料 实验室光源辐照方法 第4部分 明火炭弧灯》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2013 Plastics Methods of exposure to laboratory light sources Part 4: Open-flame carbon-arc lamps Plastiques Mthodes dexposition des sources lumineuses de laboratoire Partie 4: Lampes arc au carbone INTERNATIONAL STANDARD ISO 4892-4 Third edition 2013-07-15 Reference number ISO 4892-4:2013(E) I

2、SO 4892-4:2013(E)ii ISO 2013 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the

3、 internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.or

4、g Web www.iso.org Published in Switzerland ISO 4892-4:2013(E) ISO 2013 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative references 1 3 Principle 1 4 Apparatus . 2 4.1 Laboratory light source . 2 4.2 Test chamber 6 4.3 Radiometer . 7 4.4 Thermometer . 7 4.5 Moisture 7 4.6 Spe

5、cimen holders . 7 4.7 Apparatus to assess changes in properties 7 5 Test specimens 8 6 Test conditions . 8 6.1 Temperature 8 6.2 Relative humidity of air . 8 6.3 Spray cycle 8 6.4 Cycles with dark periods 8 7 Procedure. 9 7.1 Mounting the test specimens 9 7.2 Exposure . 9 7.3 Measurement of radiant

6、exposure . 9 7.4 Determination of changes in properties after exposure . 9 8 Exposure report 9 Bibliography .10 ISO 4892-4:2013(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Inter

7、national Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison wit

8、h ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives

9、, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives Attention is drawn to the possibility that some of the e

10、lements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations rece

11、ived. www.iso.org/patents Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 6, Ageing, chemical and environmental resistance. This third ed

12、ition cancels and replaces the second edition (ISO 4892-4:2004), of which it constitutes a minor revision. It also incorporates Technical Corrigendum ISO 4892-4:2004/Corr.1:2005. ISO 4892 consists of the following parts, under the general title Plastics Methods of exposure to laboratory light source

13、s: Part 1: General guidance Part 2: Xenon-arc lamps Part 3: Fluorescent UV lamps Part 4: Open-flame carbon-arc lampsiv ISO 2013 All rights reserved INTERNATIONAL ST ANDARD ISO 4892-4:2013(E) Plastics Methods of exposure to laboratory light sources Part 4: Open-flame carbon-arc lamps 1 Scope This par

14、t of ISO 4892 specifies methods for exposing specimens to open-flame carbon-arc lamps in the presence of moisture to reproduce the weathering effects that occur when materials are exposed in actual end-use environments in daylight or daylight filtered through window glass. The specimens are exposed

15、to filtered open-flame carbon-arc light under controlled environmental conditions (temperature, moisture). Various filters are described. Specimen preparation and evaluation of the results are covered in other International Standards for specific materials. General guidance is given in ISO 4892-1. 2

16、 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable to its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendme

17、nts) applies. ISO 4582, Plastics Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources ISO 4892-1:1999, Plastics Methods of exposure to laboratory light sources Part 1: General guidance 3 Principle 3.1 S

18、pecimens of the materials to be tested are exposed to glass-filtered open-flame carbon-arc light, to heat and to moisture continuously or in repetitive cycles. 3.2 The exposure conditions may be varied by selection of: a) the light filter; b) the type of exposure to moisture/humidity; c) the length

19、of exposure to light and moisture/humidity; d) the temperature of the exposure; e) the relative lengths of the light and dark periods. The effect of moisture is usually produced by controlling the humidity of the air or by spraying the test specimens with demineralized/deionized water or by condensa

20、tion of water vapour on to the surfaces of the specimens. 3.3 The procedure may include measurements of the irradiance and radiant exposure at the surface of the specimens. ISO 2013 All rights reserved 1 ISO 4892-4:2013(E) 3.4 It is recommended that a similar material of known behaviour (a control)

21、be exposed simultaneously with the test specimens to provide a reference standard for comparative purposes. 3.5 Intercomparison of results obtained from specimens exposed in different apparatus should not be made unless an appropriate statistical relationship has been established between the devices

22、 for the particular material tested. 4 Apparatus 4.1 Laboratory light source 4.1.1 General Open-flame carbon-arc light sources typically use three or four pairs of carbon rods, which contain a mixture of rare-earth metal salts and have a surface coating of a metal, such as copper. An electric curren

23、t is passed between the carbon rods, which burn, giving off ultraviolet, visible and infrared radiation. The pairs of carbon rods are burned in sequence, with one pair burning at any one time. Use the carbon rods recommended by the manufacturer of the apparatus. The radiation reaching the specimens

24、passes through glass filters. Three types of glass filter are used in practice. Tables 1 and 2 show the typical relative spectral irradiance for open-flame carbon-arc lamps with daylight and window-glass filters, respectively. When extended-UV filters are used, the relative spectral irradiance shall

25、 meet the requirements of Table 3. 4.1.2 Spectral irradiance of open-flame carbon-arc lamps with daylight filters (type 1) Table 1 shows typical relative spectral irradiance in the UV wavelength range of an open-flame carbon- arc lamp with daylight filters in order to simulate daylight (see CIE Publ

26、ication No. 85:1989, Table 4). Table 1 Typical relative spectral irradiance for open-flame carbon-arc lamps with daylight filters (type 1) ab Spectral passband = wavelength in nanometres (nm) Typical distribution for open- flame carbon-arc lamp with daylight filters c % CIE No. 85:1989, Table 4 de %

27、 290 0,05 290 320 2,9 5,4 320 360 20,5 38,2 360 400 76,6 56,4 aThis table gives the irradiance in the given passband, expressed as a percentage of the total irradiance between 290 nm and 400 nm. To determine the relative spectral irradiance for a specific daylight filter or set of filters for an ope

28、n-flame carbon-arc lamp, the relative spectral irradiance shall be measured from 250 nm to 400 nm. Typically, this is done in 2 nm increments. The total irradiance in each passband is then summed and divided by the total irradiance between 290 nm and 400 nm. bThis table gives typical data for an ope

29、n-flame carbon-arc lamp with borosilicate-glass daylight filters. At the time of publication of this part of ISO 4892, not enough data are available to develop a specification for the open-flame carbon-arc lamp with a daylight filter. cFor any individual relative spectral irradiance, the calculated

30、percentages for the passbands in this table will sum to 100 %. dThe data from Table 4 of CIE Publication No. 85:1989 is the global solar irradiance on a horizontal surface for an air mass of 1,0, an ozone column of 0,34 cm at STP, 1,42 cm of precipitable water vapour and a spectral optical depth of

31、aerosol extinction of 0,1 at 500 nm. These data are provided for comparison purposes only. eFor the solar spectrum represented by Table 4 of CIE No. 85:1989, the UV irradiance (290 nm to 400 nm) is 11 % and the visible irradiance (400 nm to 800 nm) is 89 %, expressed as a percentage of the total irr

32、adiance from 290 nm to 800 nm.2 ISO 2013 All rights reserved ISO 4892-4:2013(E) 4.1.3 Spectral irradiance of open-flame carbon-arc lamps with window-glass filters (type 2) Table 2 shows typical relative spectral irradiance in the UV wavelength range of an open-flame carbon- arc lamp with window-glas

33、s filters. Table 2 Typical relative spectral irradiance for open-flame carbon-arc lamps with window-glass filters (type 2) ab Spectral passband = wavelength in nanometres (nm) Typical distribution for open- flame carbon-arc lamp with window-glass filters c % CIE No. 85:1989, Table 4, plus effect of

34、window glass de % 300 0,0 300 320 0,3 1 320 360 18,7 33,1 360 400 81,0 66,0 aThis table gives the typical irradiance in the given passband, expressed as a percentage of the total irradiance between 290 nm and 400 nm. To determine the irradiance in each passband for an open-flame carbon-arc lamp with

35、 a specific set of window-glass filters, the relative spectral irradiance shall be measured from 250 nm to 400 nm. Typically, this is done in 2 nm increments. The total irradiance in each passband is then summed and divided by the total irradiance between 290 nm and 400 nm. bThis table gives typical

36、 data for an open-flame carbon-arc lamp with window-glass filters. At the time of publication of this part of ISO 4892, there is not enough data available to develop a specification for the relative spectral irradiance. cFor any individual relative spectral irradiance, the calculated percentages for

37、 the passbands in this table will sum to 100 %. Contact the manufacturer of the carbon-arc apparatus for the relative spectral irradiance data for the particular carbon arcs and window-glass filters used. dThe data from Table 4 of CIE No. 85:1989 plus the effect of window glass was determined by mul

38、tiplying the data from Table 4 of CIE No. 85:1989 by the upper and lower transmission ranges typical for window glass used in the USA and Europe. These data are provided for comparison purposes only. eFor the CIE No. 85:1989 Table 4 plus window glass data, the UV irradiance between 300 nm and 400 nm

39、 ranges from 7,7 % to 10,6 % and the visible radiation ranges from 89,4 % to 92,3 %, expressed as a percentage of the total irradiance between 300 nm and 800 nm. 4.1.4 Spectral irradiance of open-flame carbon-arc lamps with extended-UV filters (type 3) Table 3 shows relative spectral irradiance in t

40、he UV wavelength range for an open-flame carbon-arc lamp with extended-UV filters. There are several suitable type 3 filters available on the market. ISO 2013 All rights reserved 3 ISO 4892-4:2013(E) Table 3 Relative spectral irradiance for open-flame carbon-arc lamps with extended-UV filters (type

41、3) ab Spectral passband = wavelength in nanometres (nm) Minimum c % Maximum c % CIE No. 85:1989, Table 4 de % 290 4,9 290 320 2,3 6,7 5,4 320 360 16,4 24,3 38,2 360 400 68,1 80,1 56,4 aThis table gives the irradiance in the given passband, expressed as a percentage of the total irradiance between 25

42、0 nm and 400 nm. To determine whether a specific filter or set of filters for an open-flame carbon-arc lamp meets the requirements of this table, the relative spectral irradiance shall be measured from 250 nm to 400 nm. Typically, this is done in 2 nm increments. The total irradiance in each wavelen

43、gth passband is then summed and divided by the total irradiance from 250 nm to 400 nm. bThe minimum and maximum limits in this table are based on 24 relative spectral irradiance measurements with open-flame carbon-arc lamps with filters from different production lots and of various ages, used in acc

44、ordance with the recommendations of the manufacturer. The minimum and maximum limits are at least three sigma from the mean for all the measurements. Open-flame carbon-arc lamps emit significant amounts of short-wavelength UV radiation between 250 nm and 280 nm. The intensity of this short-wavelengt

45、h UV radiation varies with the age and initial transmission properties of the extended-UV filters used, as well as the composition of the carbon rods. The composition of the carbon rods may vary between production lots and between manufacturers. cThe minimum and maximum columns will not necessarily

46、sum to 100 % because they represent the minima and maxima for the measurement data used. For any individual relative spectral irradiance, the percentages calculated for the passbands in this table will sum to 100 %. For any individual open-flame carbon-arc lamp with extended-UV filters, the calculat

47、ed percentage in each passband shall fall within the minimum and maximum limits given. Test results can be expected to differ if obtained using open-flame carbon-arc apparatuses in which the relative spectral irradiance differed by as much as that allowed by the tolerances. Contact the manufacturer

48、of the carbon-arc apparatus for specific relative spectral irradiance data for the carbon-arc lamp and filters used. dThe data from Table 4 of CIE Publication No. 85:1989 is the global solar irradiance on a horizontal surface for an air mass of 1,0, an ozone column of 0,34 cm at STP, 1,42 cm of prec

49、ipitable water vapour and a spectral optical depth of aerosol extinction of 0,1 at 500 nm. These data are provided for comparison purposes only. eFor the solar spectrum represented by Table 4 of CIE No. 85:1989, the UV irradiance (290 nm to 400 nm) is 11 % and the visible irradiance (400 nm to 800 nm) is 89 %, expressed as a percentage of the total irradiance between 290 nm and 800 nm. 4.1.5 Typical spectral irradiance: Figure 1 shows the typical spectral irradiance