ISO 29465-2008 Thermal insulating products for building applications - Determination of length and width《建筑设施用绝热产品 长度和宽度的测定》.pdf

《ISO 29465-2008 Thermal insulating products for building applications - Determination of length and width《建筑设施用绝热产品 长度和宽度的测定》.pdf》由会员分享，可在线阅读，更多相关《ISO 29465-2008 Thermal insulating products for building applications - Determination of length and width《建筑设施用绝热产品 长度和宽度的测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 29465:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 29465 First edition 2008-11-01 Thermal insulating products for building applications Determination of length and width Produits isolants thermiques destins aux applications du btiment Dtermination de la longueur et de la largeur

2、ISO 29465:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downl

3、oading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the

4、General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address g

5、iven below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at t

6、he address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedISO 29465:2008(E) ISO 2008 All rig

7、hts reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Terms and definitions. 1 3 Principle. 1 4 Apparatus 1 5 Test specimens . 1 6 Procedure 2 7 Calculation and expression of results 3 8 Accuracy of measurement. 3 9 Test report . 3 ISO 29465:2008(E) iv ISO 2008 All rights reservedF

8、oreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a te

9、chnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters

10、of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated

11、 to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible f

12、or identifying any or all such patent rights. ISO 29465 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement methods. ISO 29465:2008(E) ISO 2008 All rights reserved v Introduction This International Stand

13、ard comprises the original EN 822:1994 prepared by Technical Committee CEN/TC 88, Thermal insulating materials and products, which has been amended by ISO/TC 163/SC 1 with reference to conditioning and testing conditions in tropical countries. This International Standard is one of a series of docume

14、nts specifying test methods, based on existing European Standards, that are being adopted by ISO. This “package” of standards includes the following group of interrelated documents. International Standard Respective EN standard ISO 29465, Thermal insulating products for building applications Determi

15、nation of length and width EN 822 ISO 29466, Thermal insulating products for building applications Determination of thickness EN 823 ISO 29467, Thermal insulating products for building applications Determination of squareness EN 824 ISO 29468, Thermal insulating products for building applications De

16、termination of flatness EN 825 ISO 29469, Thermal insulating products for building applications Determination of compression behaviour EN 826 ISO 29470, Thermal insulating products for building applications Determination of the apparent density EN 1602 ISO 29471, Thermal insulating products for buil

17、ding applications Determination of dimensional stability under constant normal laboratory conditions (23C/50 % relative humidity) EN 1603 ISO 29472, Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 160

18、4 ISO 29764, Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature conditions EN 1605 ISO 29765, Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1607 ISO 29

19、766, Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1608 ISO 29767, Thermal insulating products for building applications Determination of short- term water absorption by partial immersion EN 1609 ISO 29768, Thermal insulating products fo

20、r building applications Determination of linear dimensions of test specimens EN 12085 ISO 29769, Thermal insulating products for building applications Determination of behaviour under point load EN 12430 ISO 29465:2008(E) vi ISO 2008 All rights reservedISO 29770, Thermal insulating products for buil

21、ding applications Determination of thickness for floating-floor insulating products EN 12431 ISO 29771, Thermal insulating materials for building applications Determination of organic content EN 13820 ISO 29803, Thermal insulation products for building applications Determination of the resistance to

22、 impact of external thermal insulation composite systems (ETICS) EN 13497 ISO 29804, Thermal insulation products for building applications Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material EN 13494 ISO 29805, Thermal insulation product

23、s for building applications Determination of the mechanical properties of glass fibre meshes EN 13496 INTERNATIONAL STANDARD ISO 29465:2008(E) ISO 2008 All rights reserved 1 Thermal insulating products for building applications Determination of length and width 1 Scope This International Standard sp

24、ecifies the equipment and procedures for determining the length and width of full-size products. It is applicable to thermal insulating products. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 length l longer linear dimension of the major su

25、rface of the test specimen 2.2 width b shorter linear dimension of the major surface of the test specimen, measured at right angles to the length 3 Principle A specimen is placed on a flat surface and direct linear measurement is made with a metal rule or a metal tape. 4 Apparatus 4.1 Flat surface.

26、4.2 Metal rule or metal tape, graduated in millimetres and permitting reading to an accuracy of 0,5 mm. Any test equipment that provides the same result with at least the same accuracy may be used. 5 Test specimens 5.1 Dimensions of test specimens The test specimen shall be the full-size product. 5.

27、2 Number of test specimens The number of test specimens shall be as specified in the relevant product standard. In the absence of a product standard, the number of test specimens may be agreed between parties. ISO 29465:2008(E) 2 ISO 2008 All rights reserved5.3 Conditioning of test specimens The tes

28、t specimens shall be stored for at least 6 h at (23 5) C. In cases of dispute, they shall be stored at (23 2) C and (50 5) % relative humidity for the time specified in the relevant product standard. In tropical countries, different conditioning and testing conditions can be relevant. In this case,

29、the conditions shall be 27 C and 65 % RH, and be stated clearly in the test report. 6 Procedure 6.1 Test conditions The test shall be carried out at (23 5) C. In case of dispute, it shall be carried out at (23 2) C and (50 5) % relative humidity. In tropical countries, different conditioning and tes

30、ting conditions can be relevant. In this case, the conditions shall be 27 C and 65 % RH, and be stated clearly in the test report. 6.2 Test procedure Lay the test specimen carefully on a flat surface. For test specimens with both dimensions less than or equal to 1,5 m, take one measurement of length

31、, l, and one measurement of width, b, at the positions shown in Figure 1. For test specimens greater than 1,5 m long, make one additional width measurement for each extra metre of length, up to a maximum of five measurements, with the measurements equally spaced as shown in Figure 2. In this case, b

32、 is the mean value of all measured values of the width. For test specimens greater than 1,5 m wide, make one additional length measurement for each extra 1 m of width, with the measurements equally spaced. All lengths and widths shall be read to the nearest millimetre. Figure 1 Positions for measuri

33、ng length and width of a test specimen where lu 1,5 m and b u 1,5 m ISO 29465:2008(E) ISO 2008 All rights reserved 3b is the mean value of all measured values of the width. Figure 2 Positions for measuring length and width of a test specimen where l W 4,5 m and b u 1,5 m 7 Calculation and expression

34、 of results The length and width shall be expressed in millimetres, to the nearest millimetre, as the mean value for each specimen. For products 3 m long or greater, the mean length value shall be reported to the nearest 5 mm. 8 Accuracy of measurement NOTE It has not been possible to include a stat

35、ement of the accuracy of the method in this edition of this International Standard, but it is intended to include such a statement when this International Standard is next revised. 9 Test report The test report shall include the following information: a) reference to this International Standard; b)

36、product identification: 1) product name, factory, manufacturer or supplier, 2) production code number, 3) type of product, 4) packaging, 5) form in which the product arrived at the laboratory, 6) other information as appropriate, e.g. nominal thickness, nominal density; ISO 29465:2008(E) 4 ISO 2008

37、All rights reservedc) test procedure: 1) pre-test history and sampling (name of person taking the samples and sampling site), 2) conditioning, 3) deviations from Clauses 5 and 6, if any, 4) conditioning and testing conditions in tropical countries, if applicable, 5) date of test, 6) general informat

38、ion relating to the test, 7) any occurrences that can have affected the results; NOTE Information about the apparatus and identity of the technician should be available in the laboratory, but it need not be recorded in the report. d) results: all individual values and the mean value for each dimension. ISO 29465:2008(E) ICS 91.100.60 Price based on 4 pages ISO 2008 All rights reserved