ISO 2846-2-2007 Graphic technology - Colour and transparency of printing ink sets for four-colour printing - Part 2 Coldset offset lithographic printing《印刷技术 四色.pdf

《ISO 2846-2-2007 Graphic technology - Colour and transparency of printing ink sets for four-colour printing - Part 2 Coldset offset lithographic printing《印刷技术 四色.pdf》由会员分享，可在线阅读，更多相关《ISO 2846-2-2007 Graphic technology - Colour and transparency of printing ink sets for four-colour printing - Part 2 Coldset offset lithographic printing《印刷技术 四色.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 2846-2:2007(E) ISO 2007INTERNATIONAL STANDARD ISO 2846-2 Second edition 2007-12-15 Graphic technology Colour and transparency of printing ink sets for four- colour printing Part 2: Coldset offset lithographic printing Technologie graphique Couleur et transparence des gammes den

2、cre dimpression en quadrichromie Partie 2: Impression lithographique offset rotatif coldset ISO 2846-2:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces whic

3、h are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Inc

4、orporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event t

5、hat a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechani

6、cal, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.o

7、rg Published in Switzerland ii ISO 2007 All rights reservedISO 2846-2:2007(E) ISO 2007 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope 1 2 Normative references 1 3 Terms and definitions .1 4 Test method2 4.1 Principle2 4.2 Test print preparation2 5 Requirements for colour, t

8、ransparency and ink film thickness range.3 5.1 Colour .3 5.2 Transparency characteristics.4 5.3 Ink film thickness range4 Annex A (normative) Reference substrate .5 Annex B (informative) Detailed explanation of testing including examples .6 Annex C (informative) Spectral data9 Bibliography 11 ISO 28

9、46-2:2007(E) iv ISO 2007 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each membe

10、r body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Elec

11、trotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopt

12、ed by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of paten

13、t rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2846-2 was prepared by Technical Committee ISO/TC 130, Graphic technology. This second edition cancels and replaces the first edition (ISO 2846-2:2000), of which Clauses 4 and 5 have been technically revis

14、ed and the colorimetric properties of the inks were adjusted to be compatible with actual commercial requirements and to the process standard ISO 12647-3 1 . Details for test print preparation, which are now specified in ISO 2834-1, have been deleted. ISO 2846 consists of the following parts, under

15、the general title Graphic technology Colour and transparency of printing ink sets for four-colour printing: Part 1: Sheet-fed and heat-set web offset lithographic printing Part 2: Coldset offset lithographic printing Part 3: Publication gravure printing Part 4: Screen printing Part 5: Flexographic p

16、rinting ISO 2846-2:2007(E) ISO 2007 All rights reserved v Introduction The initial draft of ISO 2846-2 was prepared by ISO/TC 130 for materials and process control. They examined the colorimetric properties of commercial coldset web offset inks from around the world and found that a single set of co

17、lour coordinates could adequately represent these, within reasonable tolerances. Since the initial publication of this part of ISO 2846, additional coordination between the various national bodies participating in ISO/TC 130 has suggested that some minor refinements of the colorimetric aims would ma

18、ke them more compatible with actual commercial printing requirements and to the process standard ISO 12647-3 1 . This part of ISO 2846 will allow printers to obtain sets of process inks from various sources which will produce a similar colour when printed on the reference substrate at the appropriat

19、e film thickness. This will allow colour separations for coldset web offset printing to be based on known colour standards. The colorimetric characteristics specified in this part of ISO 2846 may only be obtained when the inks are printed on the reference substrate. However, similarity of two inks o

20、n the reference substrate will ensure similarity on another substrate. INTERNATIONAL STANDARD ISO 2846-2:2007(E) ISO 2007 All rights reserved 1 Graphic technology Colour and transparency of printing ink sets for four-colour printing Part 2: Coldset offset lithographic printing 1 Scope This part of I

21、SO 2846 specifies the colour and transparency to be produced by inks intended for four-colour coldset web offset printing when printed under specified conditions on a printability tester. It also describes the test method to ensure conformance. This part of ISO 2846 is not applicable to fluorescent

22、inks and does not specify pigments (or spectral reflectance) so as not to preclude the use of future suitable pigment combinations and still claim compliance with its colorimetric requirements. 2 Normative references The following referenced documents are indispensable for the application of this do

23、cument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 536, Paper and board Determination of grammage ISO 2471, Paper and board Determination of opacity (paper backing) Diffuse reflec

24、tance method ISO 2834-1, Graphic technology Laboratory preparation of test prints Part 1: Paste inks ISO 8791-4, Paper and board Determination of roughness/smoothness (air leak methods) Part 4: Print- surf method ISO 13655, Graphic technology Spectral measurement and colorimetric computation for gra

25、phic arts images ANSI/CGATS.5:2003, Graphic technology Spectral measurement and colorimetric computation for graphic arts images 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 coldset printing web offset printing without accelerated drying N

26、OTE Ink sets by absorption into the substrate. ISO 2846-2:2007(E) 2 ISO 2007 All rights reserved3.2 standard ink ink, intended for four-colour printing, which, when printed on the reference substrate and within the applicable range of ink film thicknesses, complies to the colorimetric and transparen

27、cy specifications of this part of ISO 2846 3.3 primary colours colours of individual prints from yellow, magenta and cyan inks NOTE If the prints are produced as specified in this part of ISO 2846 and conform to the colorimetric characteristics specified, they are standard primary colours. 3.4 trans

28、parency ability of an ink film to transmit light, generally expressed as some measure of the unwanted scattering 3.5 transparency measurement value T reciprocal of the slope of the regression line between ink film thickness and colour difference for overprints of chromatic inks over black 4 Test met

29、hod 4.1 Principle Each ink is printed on the reference substrate described in Annex A at a range of ink film thicknesses. The colours which result are measured colorimetrically. Transparency is evaluated by printing each of the three primary colours on a black substrate at a range of film thicknesse

30、s. The CIELAB colour difference is determined for each sample, between the printed and unprinted black, and the linear regression coefficient (slope of the regression line) between ink film thickness and colour difference is calculated for each colour. For a detailed description of procedures, toget

31、her with examples, see the informative Annex B. 4.2 Test print preparation 4.2.1 Prints for colorimetric evaluation For each of the inks to be evaluated, a number of test prints shall be made using a printability tester, each produced at a different ink film thickness in accordance with the conditio

32、ns specified in ISO 2834-1. They shall be made on the reference substrate as specified in Annex A. The sample material shall be kept in the dark under standard conditions of 23 C and 50 % RH. The range of ink film thicknesses produced shall encompass that specified in 5.3. In cases where the approxi

33、mate ink film thickness is known to result in the closest match of the target colorimetric values, a minimum of three prints shall be made. Otherwise, a minimum number of five prints should be made covering the full range of specified film thicknesses. 4.2.2 Prints for transparency evaluation Test p

34、rints for transparency evaluation shall be produced by printing the inks to be tested on a black substrate using a printability tester. Measurements of the CIELAB values of the black substrate shall be made prior to overprinting. The black shall have a lightness (L*) less than 30 when determined in

35、accordance with ISO 13655. ISO 2846-2:2007(E) ISO 2007 All rights reserved 3 The ink to be tested shall then be printed on the black substrate 1)in accordance with the conditions specified in ISO 2834-1, such that a range of samples, each with a different ink film thickness, is achieved. The range s

36、hould approximate that defined in 5.3. 4.2.3 Setting of test prints Prior to colour measurement, all printed samples shall be left for at least 12 h to enable setting of the ink. 4.2.4 Colour measurement procedure Test prints shall be measured in accordance with ISO 13655 with the exception that a w

37、hite backing, in accordance with ANSI/CGATS.5:2003, shall be used. NOTE 1 The requirements for white backing given in ANSI/CGATS.5:2003 are consistent with the future revision of ISO 13655. NOTE 2 The colorimetric values are related to the measurement procedure specified in ISO 13655. This means tha

38、t the samples are measured spectrally, with a 0:45 (0:45 indicates the relationship between incident light and reflected light measurement angles) or 45:0 geometry instrument. For the calculation of CIELAB values and for the colour difference, the CIE 1931 (2) standard colorimetric observer data are

39、 used together with CIE standard illuminant D50. 5 Requirements for colour, transparency and ink film thickness range 5.1 Colour For an ink to conform to this part of ISO 2846, it shall meet the following requirements: a) when printed as specified in 4.2.1, at some ink film thickness within the rang

40、e specified in 5.3, the ink shall meet the colorimetric target value and tolerance specified in Table 1; b) it shall meet the transparency requirements specified in 5.2. NOTE Typical spectral data for inks conforming to this part of ISO 2846 are provided in Annex C. Table 1 Colorimetric values CIELA

41、B values Tolerances Ink L* a* b* * ab E L* a* b* Yellow 80,4 (78,0) 1,4 (3,0) 61,6 (58,0) 4,0 (4,0) Magenta 55,5 (54,0) 47,6 (44,0) 0,7 (2,0) 4,0 (4,0) Cyan 59,1 (57,0) 23,9 (23,0) 27,1 (27,0) 4,0 (4,0) Black 36,8 (36,0) 1,5 (1,0) 4,5 (4,0) u 36,8a(u 36,0a ) 1,0 ( 1,0) 2,0 ( 2,0) Values in brackets

42、pertain to measurement on black backing in accordance with ISO 13655 and are given for information only. aThis means that for black there is no symmetrical tolerance for L* but an upper limit.1) Contact the ISO/TC 130 Secretariat (DIN) for the source of a suitable substrate. ISO 2846-2:2007(E) 4 ISO

43、 2007 All rights reserved5.2 Transparency characteristics To meet the specification for transparency an ink shall produce a value greater than that specified in Table 2 when determined by the principles and procedures outlined in 4.1 and 4.2.2. Table 2 Transparency Ink colour Transparency measuremen

44、t value T Yellow 0,1 Magenta 0,2 Cyan 0,3 NOTE For highly transparent inks (usually cyan), the slope of the regression line may be zero or negative. In such a situation, the transparency measurement value is considered to be approaching infinity and therefore the ink meets the specification. For fur

45、ther information concerning transparency evaluation, see B.2. 5.3 Ink film thickness range The range of ink film thickness, within which a standard ink for coldset lithographic printing shall conform to the colorimetric values specified in 5.1, is 0,7 m to 1,3 m. ISO 2846-2:2007(E) ISO 2007 All righ

46、ts reserved 5 Annex A (normative) Reference substrate The characteristics of the reference substrate shall be the following. a) Colour The colour values for the reference substrate are given based on white backing. In addition, black backing values are given for information. white backing black back

47、ing CIELAB values L* = 85,2 4,0 L* = 82,0 4,0 a* = 0,9 2,0 a* = 0,0 2,0 b* = 5,2 2,0 b* = 3,0 2,0 Method: ISO 13655 (0:45, D50, 2, with the exception that white backing shall be used, as described in 4.2.4). b) Mass per area Specification: (48,8 2) g/m 2Method: ISO 536 c) Opacity Specification: 94 %

48、 Method: ISO 2471 d) Roughness Specification: (3,4 0,2) m at a pressure of 1 MPa Method: ISO 8791-4 ISO 2846-2:2007(E) 6 ISO 2007 All rights reservedAnnex B (informative) Detailed explanation of testing including examples B.1 Colorimetric verification In order to evaluate whether an ink complies wit

49、h this part of ISO 2846, it is necessary to print a number of samples, each of known ink film thickness, which adequately represent the range of ink film thicknesses specified in 5.3. These samples may be prepared on a printability tester by running up a small quantity of ink on the inking system, weighing the printing forme prior to printing and then printing the test sample on the reference substrate. The printing forme is then re-weighed and the