ISO 2776-1974 Modular co-ordination Co-ordinating sizes for doorsets External and internal《模数协调 整樘门的协调尺寸 外门和内门》.pdf

《ISO 2776-1974 Modular co-ordination Co-ordinating sizes for doorsets External and internal《模数协调 整樘门的协调尺寸 外门和内门》.pdf》由会员分享，可在线阅读，更多相关《ISO 2776-1974 Modular co-ordination Co-ordinating sizes for doorsets External and internal《模数协调 整樘门的协调尺寸 外门和内门》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD INTERNATIONAL ORGANIZATION FOR STANDARDIZATION +EEYHAPoJHAII OPAHH3ILWiCIR l-IO CTAHAAFTH3ALWi.ORGANISATION INTERNATIONALE DE NORMALISATION Modular co-ordination - Co-ordinating sizes for doorsets - External and. internal Coordination modulaire - Dimensions de coordination des

2、 portes extbieures et in t these components will be required to fill the spaces determined by a controlling reference system. The component consid- ered in this International Standard is the doorset, for which are given the co-ordinating width and height. This International Standard applies to exter

3、nal and internal doorsets for use in the construction of buildings of all types. 3 DEFINITIONS The spaces for this component have been related to the horizontal planes of the controlling reference system. Two types of doorset are considered depending on the control- ling reference planes to which th

4、eir vertical dimensions are related, as shown below : For the purpose of this International Standard, the definitionsgiven in IS0 1791 and IS0 1804 shall apply. Oh . . . . n.-.-.3 . . . . , . . . . . .“rm I_.” *, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5、 . . . . . . . . . Floor . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . ,-,.,.,.,.,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * A a . . . . . . . a.* ,.* . ,., - ,.*.,., * ,.,.,. .,.,.,.,. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6、 . . . . . . . . . . . .*.*.*.,. O-n- . . . . . . . . . . . . . . . . . . . . . . . . . *=u*.* Ceiling “-tl-IT- Door head 1 SCOPE This International Standard specifies the co-ordinating sizes for doorsets of all materials to be used in buildings, and which will fill co-ordinating spaces in dimension

7、ally co-ordinated buildings. It is based on the principles of modular co-ordination, and is in accordance with the IS0 documents listed in the Foreword. NOTE - This International Standard gives a range of sizes limited to those which have been accepted by Member Bodies (national standards may includ

8、e additional sizes). Notice will be taken of experience in the use of all these sizes when considering a revision of this International Standard. 1 ) 4 SPECIFICATION 4.1 The co-ordinating sizes for external doorsets shall be as follows : Width Height 9M 21 M 10 M 24 M 12 M 27 M I5 M 30 M I8 M 21 M 2

9、4 M 4.2 The co-ordinating sizes for internal doorsets shall be as follows : Width 7M 8M 9M IOM I2 M 15M I8 M 21 M Height 21 M 24 M 27 M 30 M NOTE - M is the symbol for the basic module defined in IS0 1006 and having the value 100 mm. 1) Member Bodies are requested to give information on the application of this range of sizes. 1 Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-