ISO 24102-2-2015 Intelligent transport systems - Communications access for land mobiles (CALM) - ITS station management - Part 2 Remote management of ITS-SCUs《智.pdf

《ISO 24102-2-2015 Intelligent transport systems - Communications access for land mobiles (CALM) - ITS station management - Part 2 Remote management of ITS-SCUs《智.pdf》由会员分享，可在线阅读，更多相关《ISO 24102-2-2015 Intelligent transport systems - Communications access for land mobiles (CALM) - ITS station management - Part 2 Remote management of ITS-SCUs《智.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2015 Intelligent transport systems Communications access for land mobiles (CALM) ITS station management Part 2: Remote management of ITS-SCUs Systmes intelligents de transport Accs aux communications des services mobiles terrestres (CALM) Gestion de la station ITS Partie 2: Gestion distance des

2、 SCUs-ITS INTERNATIONAL STANDARD ISO 24102-2 First edition 2015-12-01 Reference number ISO 24102-2:2015(E) ISO 24102-2:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication m

3、ay be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of th

4、e requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO 24102-2:2015(E)Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Symbols and abbr

5、eviated terms . 2 5 Requirements 2 6 Remote management architecture 3 6.1 Functionality . 3 6.2 ITS station architecture . 6 6.3 Distributed implementation of an ITS-S . 6 6.4 RMPE . 6 6.5 RMCH . 7 7 Remote management protocol data units 8 8 Service primitive functions . 9 8.1 Generic service primit

6、ives 9 8.2 MF-SAP service primitive functions 9 8.2.1 Transmission request of RSMP-Request and RSMP-Response 9 8.2.2 Notification of reception of RSMP-Request and RSMP-Response 9 8.3 SF-SAP service primitive functions .10 8.3.1 Security procedure applied to RSMP-Request and RSMP-Response .10 8.3.2 S

7、ecurity procedure applied to RMCH-Request and RSMP-Response 10 9 Remote management procedures11 9.1 Remote management session initiation .11 9.1.1 Initiation by server11 9.1.2 Initiation by client 11 9.1.3 RSMP session identifier 11 9.1.4 RSMP session security .11 9.2 Remote management session closu

8、re 11 9.2.1 Active closure .11 9.2.2 Timeout .11 9.2.3 No active session .12 9.3 Firmware update 12 9.4 Maintenance of ITS-S protocols .12 9.5 Maintenance of ITS-S application processes 13 9.6 Maintenance of configuration information .14 10 Usage of FSAP 14 10.1 General 14 10.2 SAM 14 10.3 CTX .14 A

9、nnex A (normative) ASN.1 modules 15 Annex B (informative) Communication service parameters 23 Bibliography .24 ISO 2015 All rights reserved iii Contents Page ISO 24102-2:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (

10、ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, go

11、vernmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further main

12、tenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Att

13、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introducti

14、on and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to confo

15、rmity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 204, Intelligent transport systems. This first edition, toget

16、her with ISO 24102-1, ISO 24102-3, ISO 24102-4, ISO 24102-5 and ISO 24102-6, cancels and replaces ISO 24102:2010, which has been technically revised. ISO 24102 consists of the following parts, under the general title Intelligent transport systems Communications access for land mobiles (CALM) ITS sta

17、tion management: Part 1: Local management Part 2: Remote management of ITS-SCUs Part 3: Service access points Part 4: Station-internal management communications Part 5: Fast service advertisement protocol (FSAP) Part 6: Path and flow managementiv ISO 2015 All rights reserved ISO 24102-2:2015(E) Intr

18、oduction This part of ISO 24102 is part of a family of International Standards for communications access for land mobiles (CALM). An introduction to the whole set of International Standards for Intelligent Transport Systems (ITS) is provided in ISO 21217. This part of ISO 24102 is the second part of

19、 a multipart International Standard which determines remote management of an ITS station unit (ITS-SU) with the ITS station and communication architecture specified in ISO 21217 and illustrated in Figure 1, and operated as a bounded secured managed domain (BSME). Remote ITS station management has th

20、e purpose of setting, updating, and deletion of configuration and operation information in an ITS station communication units (ITS-SCU) of an ITS station unit (ITS-SU) specified in ISO 21217, e.g. information on policies and regulations, security related information, accounting information, access l

21、ayer parameters (see Reference 1), installation, update, and deinstallation of persistent information in an ITS-SCU, e.g. ITS-S application processes specified in ISO 21217, ITS-S communication protocols, and notification and retrieval of management information, e.g. log files of events, alarms gene

22、rated by the ITS-SCU(s) of an ITS-SU. By this, it covers the five management areas identified in ISO/IEC 7498-4. Communications Access Networking & Transport Management Security Facilities Applications IN NF MS MI MN MF SF SN SI API Figure 1 ITS station reference architecture ISO 2015 All rights res

23、erved v Intelligent transport systems Communications access for land mobiles (CALM) ITS station management Part 2: Remote management of ITS-SCUs 1 Scope This part of ISO 24102 provides specifications for Intelligent Transport Systems (ITS) station management to be compliant with the ITS station refe

24、rence architecture and the set of related standards from ISO/TC 204. Remote ITS station management is specified by means of protocol data units (PDUs) and procedures of the “Remote ITS Station Management Protocol” (RSMP) related to managed objects in an ITS station unit. Distinction is made between

25、managed ITS station units (management clients) and managing remote ITS station units (management servers). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editio

26、n cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 21217, Intelligent transport systems Communications access for land mobiles (CALM) Architecture ISO 24102-1, Intelligent transport systems Communications access for land mob

27、iles (CALM) ITS station management Part 1: Local management ISO 24102-3, Intelligent transport systems Communications access for land mobiles (CALM) ITS station management Part 3: Service access points ISO 24102-4, Intelligent transport systems Communications access for land mobiles (CALM) ITS stati

28、on management Part 4: Station-internal management communications ISO/IEC 7498-4, Information processing systems Open Systems Interconnection Basic Reference Model Part 4: Management framework ISO/IEC 8825-2, Information technology ASN.1 encoding rules: Specification of Packed Encoding Rules (PER) 3

29、T erms a nd definiti ons For the purposes of this document, the terms and definitions given in ISO 21217, ISO 24102-1, ISO 24102-3, ISO 24102-4, ISO/IEC 7498-4, and the following apply. 3.1 remote management client ITS station communication unit in which remote ITS station management is performed by

30、 a remote management server (3.2) 3.2 remote management server entity performing remote ITS station management in an ITS station communication unit INTERNATIONAL ST ANDARD ISO 24102-2:2015(E) ISO 2015 All rights reserved 1 ISO 24102-2:2015(E) 4 Symbols and abbreviated terms For the purposes of this

31、document, the abbreviated terms given in ISO 21217, ISO 24102-1, ISO 24102-3, ISO/IEC 7498-4, and the following apply. BSME Bounded Secured Managed Entity (from ISO 21217) IICP ITS station-Internal management Communications Protocol (from ISO 24102-4) FSAP Fast Service Advertisement Protocol (from I

32、SO 24102-5) ITS Intelligent Transport Systems ITS-SCU ITS Station Communication Unit (from ISO 21217) ITS-SCU-CMC ITS-SCU Configuration Management Centre (from CEN/ISO/TS 17419) ITS-SU ITS Station Unit (from ISO 21217) RMC Remote Management Client RMCH Remote Management Communication Handler RMPE Re

33、mote Management Protocol Execution RMS Remote Management Server RSMP Remote ITS station Management Protocol 5 Requirements The ITS station management entity shall provide the functionality specified in the various parts of this multipart International Standard. 1) The functionality of local ITS stat

34、ion management specified in ISO 24102-1. 2) The functionality of remote ITS station management specified in this part of ISO 24102. 3) The functionality of management service access points specified in ISO 24102-3. 4) The functionality of ITS station-internal management communications specified in I

35、SO 24102-4. 5) The functionality of the “Fast Service Advertisement Protocol” (FSAP) specified in ISO 24102-5. 6) The functionality of the path and flow management specified in ISO 24102-6. Means to secure the access to management functionality need to be specified within the global context of ITS s

36、ecurity. Details are outside the scope of this part of ISO 24102. Detailed mandatory requirements are specified in the following clauses of this part of ISO 24102. Clause 6 presents the remote management architecture. Clause 7 specifies remote management protocol data units. Clause 8 specifies servi

37、ce primitive functions. Clause 9 specifies remote management procedures. Clause 10 specifies details needed for the Fast Service Advertisement Protocol (FSAP). Annex A specifies the ASN.1 module for remote management.2 ISO 2015 All rights reserved ISO 24102-2:2015(E) Annex B proposes settings of com

38、munication service parameters used for automatic selection of communication profiles specified in CEN/ISO/TS 17423. 6 Remote management architecture 6.1 Functionality The “Remote ITS Station Management Protocol” (RSMP) specified in this part of ISO 24102 has the purpose of setting, updating, and del

39、etion of configuration and operation information in an ITS station communication unit (ITS-SCU) of an ITS station unit (ITS-SU) specified in ISO 21217, e.g. information on policies and regulations (CEN/ISO/TS 17419), security related information, accounting information, access layer parameters (see

40、Reference 1), etc., installation, update, and deinstallation of persistent information in an ITS-SCU, e.g. ITS-S application processes, ITS-S communication protocols, and notification and retrieval of management information, e.g. log files of events, alarms generated by the ITS-SCU of an ITS-SU. By

41、this, it covers the five management areas identified in ISO/IEC 7498-4. Remote ITS station management covers a set of management processes where ITS station units (ITS- SU) acting as remote management servers (RMS) manage ITS station communication units (ITS-SCU) of managed ITS-SUs acting as remote

42、management clients (RMC). An RMS is associated with an ITS-SCU configuration management centre identified in CEN/ISO/ TS 17419. An RMS may be implemented, e.g. in a roadside ITS sub-system or in a central ITS sub-system. Remote ITS station management is applied to managed objects (according to ISO/I

43、EC 7498-4) in remote management sessions. Such sessions may be initiated by the RMS (server initiated session), e.g. by means of the Fast Service Advertisement Protocol (FSAP) (see Reference 2) or by direct IPv6 based access, or by the RMC (client initiated session), typically using IPv6 communicati

44、ons, as illustrated in Figure 2 (server initiated session using FSAP), in Figure 3 (direct server initiated session), and in Figure 4 (client initiated session). The mechanisms specified in this part of ISO 24102 enable future specifications of remote management features in separate standards or by

45、means of registries. ISO 2015 All rights reserved 3 ISO 24102-2:2015(E) RMS RMC SAM( RSMP) CTX( ITS-SCUi nfo) REQW(initiates ecures ession) RES( confirmsecures ession) FSAP service initialization phase FSAP service operation phase REQW(close session) RES( confirmend ofsession REQW(managmentcommand)

46、RES( command confirmation,r esult) . . . RSMP initialization phase RSMP operation phase RSMP closing phase Figure 2 Server initiated session (example with FSAP) SAM and CTX specified in Reference 2 with details specified in this part of ISO 24102 are used in the example of Figure 2 to prepare for th

47、e secured management session. During the FSAP service operation phase, first, a secure session is requested from the RMS which is acknowledged by the RMC. After successful establishment of a session with mutual authentication of RMS and RMC with optional agreement on encryption of the management dat

48、a to be exchanged in the session, the RMS may send out a sequence of management commands, each of which is acknowledged by the RMC providing also optional result data. Finally, the RMS closes the session, which also is acknowledged by the RMC. Subsequent to this, no more management data can be excha

49、nged.4 ISO 2015 All rights reserved ISO 24102-2:2015(E) RMS RMC RES( confirmsecures ession) REQW(close session) RES( confirmend ofsession REQW(managmentcommand) RES( command confirmation,r esult) . . . REQW(initiates ecures ession) RSMP initialization phase RSMP operation phase RSMP closing phase Figure 3 Direct server initiated session In the example of Figure 3, an RMS directly initiates a secure session with an RMC. After confirmation of the s