ISO 22034-2-2016 Steel wire and wire products - Part 2 Tolerances on wire dimensions《钢丝和钢丝制品 第2部分 钢丝尺寸公差》.pdf

《ISO 22034-2-2016 Steel wire and wire products - Part 2 Tolerances on wire dimensions《钢丝和钢丝制品 第2部分 钢丝尺寸公差》.pdf》由会员分享，可在线阅读，更多相关《ISO 22034-2-2016 Steel wire and wire products - Part 2 Tolerances on wire dimensions《钢丝和钢丝制品 第2部分 钢丝尺寸公差》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2016 Steel wire and wire products Part 2: Tolerances on wire dimensions Fil produits de fil en acier Partie 2: Tolrances sur les dimensions des fils INTERNATIONAL STANDARD ISO 22034-2 Second edition 2016-04-01 Reference number ISO 22034-2:2016(E) ISO 22034-2:2016(E)ii ISO 2016 All rights reserv

2、ed COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intr

3、anet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.o

4、rg www.iso.org ISO 22034-2:2016(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 T erms and definitions . 1 4 Wire diameter tolerances . 2 4.1 General . 2 4.2 Tolerances on diameter of uncoated and metallic-coated round steel wire 2 4.3 Out-of-roundness (ovality) . 3 4.4 Tolerances on diameter o

5、f organic coated wire . 4 4.4.1 General 4 4.4.2 Extruded organic coatings . 4 4.4.3 Sintered organic coatings . 4 5 Tolerance on cut lengths 5 5.1 Length tolerances . 5 5.2 Straightness tolerances 5 6 Length of wire in coil 6 ISO 2016 All rights reserved iii Contents Page ISO 22034-2:2016(E) Forewor

6、d ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technica

7、l committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of ele

8、ctrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was

9、 drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such pate

10、nt rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not

11、constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information

12、The committee responsible for this document is ISO/TC 17, Steel, Subcommittee SC 17, Steel wire rod and wire products. This second edition cancels and replaces the first edition (ISO 22034-2:2007), which has been technically revised. ISO 22034 consists of the following parts, under the general title

13、 Steel wire and wire products: Part 1: General test methods Part 2: Tolerances on wire dimensionsiv ISO 2016 All rights reserved INTERNATIONAL ST ANDARD ISO 22034-2:2016(E) Steel wire and wire products Part 2: Tolerances on wire dimensions 1 Scope This part of ISO 22034 specifies the tolerances on t

14、he diameter of round wire and, where applicable, on the length of round wire cut to length, for bright (i.e. uncoated) steel wire, metallic-coated steel wire and non-metallic-coated steel wire. This part of ISO 22034 applies to round wires in the diameter range 0,050 mm to 25,00 mm. 2 Normative refe

15、rences The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

16、ISO 6929, Steel products Vocabulary 3 T erms a nd definiti ons For the purposes of this document, the terms and definitions given in ISO 6929 and the following apply. 3.1 wire product of constant cross section along its length, obtained by drawing a cold wire rod through a reducing die or passing it

17、 under pressure between rollers and rewinding the drawn product Note 1 to entry: Wire can be supplied with a metallic or non-metallic coating, or with both, or without a coating. 3.2 cut length straightened piece of wire cut to a specified length ISO 2016 All rights reserved 1 ISO 22034-2:2016(E) 4

18、Wire diameter tolerances 4.1 General Key 1 metallic coating thickness in mm d overall diameter in mm (including, where existing, the metallic coating) Figure 1 Sketch for Table 1 Diameter measurements shall be made at any cross-section and shall not differ from the tolerances specified in the releva

19、nt tables in this part of ISO 22034. NOTE 1 The diameter tolerances may vary when cut lengths are supplied by a third party. NOTE 2 Diameter tolerances of classes T1 to T5 (see Table 1) are calculated as follows: = , d = , d = , d = , d = , d whered is the diameter measured, in millimetres. 4.2 Tole

20、rances on diameter of uncoated and metallic-coated round steel wire The purchaser or the product standard shall indicate the tolerance range required from Table 1. The diameter shall be within the relevant tolerance range given in Table 1. NOTE Unless otherwise specified in the order/enquiry or the

21、product standard, tolerance class T1 would generally be used for heavy galvanized (A) wire, T2 would generally be used for other galvanized wire, and T3, T4 and T5 would generally be used for bright drawn wire in increasing order of precision required.2 ISO 2016 All rights reserved ISO 22034-2:2016(

22、E) Table 1 Diameter tolerances Range of wire diameter, d mm Diameter tolerance mm T1 T2 T3 T4 T5 0,30 d 0,52 0,52 d 0,74 0,74 d 1,01 1,01 d 1,31 1,31 d 1,66 1,66 d 2,05 2,05 d 2,94 2,94 d 4,01 4,01 d 5,23 5,23 d 6,62 6,62 d 8,17 8,17 d 11,76 11,76 d 16,01 16,01 d 20,90 20,90 d 25,00 0,20 d 0,31 0,31

23、 d 0,55 0,55 d 0,86 0,86 d 1,24 1,24 d 1,69 1,69 d 2,20 2,20 d 2,78 2,78 d 3,43 3,43 d 4,94 4,94 d 6,73 6,73 d 8,78 8,78 d 11,12 11,12 d 13,72 13,72 d 19,76 19,76 d 25,00 0,05 d 0,09 0,09 d 0,15 0,15 d 0,23 0,23 d 0,33 0,33 d 0,52 0,52 d 0,91 0,91 d 1,42 1,42 d 2,05 2,05 d 2,78 2,78 d 3,63 3,63 d 4,

24、60 4,60 d 5,67 5,67 d 8,17 8,17 d 11,12 11,12 d 14,52 14,52 d 18,37 18,37 d 22,68 22,68 d 25,00 0,05 d 0,072 0,072 d 0,12 0,12 d 0,17 0,17 d 0,29 0,29 d 0,45 0,45 d 0,65 0,65 d 1,01 1,01 d 1,78 1,78 d 2,78 2,78 d 4,01 4,01 d 5,45 5,45 d 7,12 7,12 d 9,01 9,01 d 11,12 11,12 d 16,01 16,01 d 21,77 21,77

25、 d 25,00 0,05 d 0,09 0,09 d 0,17 0,17 d 0,26 0,26 d 0,37 0,37 d 0,65 0,65 d 1,01 1,01 d 1,45 1,45 d 2,26 2,26 d 4,01 4,01 d 6,26 6,26 d 9,01 9,01 d 12,26 12,26 d 16,01 16,01 d 20,26 20,26 d 25,00 0,003 0,004 0,005 0,006 0,008 0,010 0,012 0,015 0,020 0,025 0,030 0,035 0,040 0,045 0,050 0,060 0,070 0,

26、080 0,090 0,100 0,120 0,140 0,160 0,180 4.3 Out-of-roundness (ovality) The out-of-roundness is the difference between the maximum and the minimum diameter of the wire at any cross-section and shall not be more than one-half of the total tolerance given in Table 1. ISO 2016 All rights reserved 3 ISO

27、22034-2:2016(E) 4.4 Tolerances on diameter of organic coated wire 4.4.1 General Key 1 metallic coating thickness, in mm d overall diameter, in mm (including, where existing, the metallic coating) D overall diameter, in mm (including organic coating) Figure 2 Sketch for Table 2 4.4.2 Extruded organic

28、 coatings The tolerances on the diameter of extruded-organic-coated wire shall be as given in Table 2. The core wire can be either bright or metallic-coated (usually zinc-coated). 4.4.3 Sintered organic coatings The tolerances on the diameter of sintered-organic-coated wire shall be as given in Tabl

29、e 2. Generally, the core wire is metallic-coated (usually zinc-coated).4 ISO 2016 All rights reserved ISO 22034-2:2016(E) Table 2 Tolerances on diameter and coating thickness of sintered- and extruded-organic- coated wire Diameter of organic-coated wire mm Tolerances on overall diameter of organic c

30、oating mm Minimum coating thickness mm Minimum concentricity % Extruded Sintered Extruded Sintered D 1,00 0,10 0,20 0,12 75 65 1,00 1000 0,10 % 5.2 Straightness tolerances There are three classes of straightness of cut lengths given in Table 5 for wire diameters specified in Table 4. The purchaser s

31、hall select the appropriate class required. Figure 3 illustrates the measurement of out of straightness. For classes 1 and 2, the cut lengths shall also meet the requirements of a rolling test which is performed on a smooth glass incline. Cut lengths are placed on the incline in a position which wil

32、l allow them to roll freely down. ISO 2016 All rights reserved 5 ISO 22034-2:2016(E) Table 4 Maximum test lengths for measurement of out-of-straightness Wire diameter, d mm Test length, L t mm 2,00 d 6,00 500 6,00 d 13,00 500 or 1 000 13,00 d 25,00 1 000 Wire of less than 2,00 mm in diameter has ins

33、ufficient rigidity in length, making the measurement of the out-of-straightness a difficult. The measurement shall therefore be made as agreed between purchaser and supplier. Table 5 Tolerances on straightness of cut lengths Class L t= 500 mm L t= 1 000 mm Rolling test 1 a = 0,5 mm a = 2 mm Will rol

34、l down an incline of 1 in 10 2 a = 1,0 mm a = 4 mm 3 No requirement Key L t test length, in mm a out-of-straightness, in mm Figure 3 Measurement of out-of-straightness 6 Length of wire in coil With a wire of known size and density, the length of the coil can be determined by weighing the coil and calculating the length from the mass thus obtained.6 ISO 2016 All rights reserved ISO 22034-2:2016(E) ISO 2016 All rights reserved IC S 77.140.65 Price based on 6 pages