ISO 16380-2014 Road vehicles - Blended fuels refuelling connector《道路车辆 混合燃料补充连接器》.pdf
《ISO 16380-2014 Road vehicles - Blended fuels refuelling connector《道路车辆 混合燃料补充连接器》.pdf》由会员分享,可在线阅读,更多相关《ISO 16380-2014 Road vehicles - Blended fuels refuelling connector《道路车辆 混合燃料补充连接器》.pdf(52页珍藏版)》请在麦多课文档分享上搜索。
1、 ISO 2014 Road vehicles Blended fuels refuelling connector Vhicules routiers Pistolet de remplissage pour les mlanges de carburants gazeux INTERNATIONAL STANDARD ISO 16380 First edition 2014-06-01 Reference number ISO 16380:2014(E) ISO 16380:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED
2、 DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permissi
3、on can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 16380:2014(E) ISO 201
4、4 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references 2 3 T erms and definitions . 2 4 General construction requirements . 3 5 Nozzles 5 6 Standard receptacle dimensions . 6 6.1 Standard receptacle dimensions Size 1 (M200, M250, M350) 6 6.2 Standard re
5、ceptacle dimensions size 2 (N200, N250) 10 7 Receptacles 12 8 Instructions .12 9 Marking .13 10 Tests 14 10.1 General requirements 14 10.2 User interface 14 10.3 Impact resistance .15 10.4 Receptacle protective caps.15 10.5 Leakage at room temperature 15 10.6 Valve operating handle 16 10.7 Abnormal
6、loads .16 10.8 Rocking/twisting17 10.9 Mounting hardware torque .18 10.10 Leakage test at low and high temperatures 18 10.11 Durability 19 10.12 Hydrostatic strength .22 10.13 Corrosion resistance .22 10.14 Deformation .23 10.15 Non-igniting evaluation 23 10.16 Vibration resistance .23 10.17 Hydroge
7、n embrittlement 23 10.18 Pressure tight protective cap (PTPC) .24 Annex A (informative) Table of nozzle characteristics .32 Annex B (informative) Manufacturing and production test plan 33 Annex C (informative) R ec eptacle t est fixtur e .34 Annex D (informative) Nozzle clearance dimensions 44 Bibli
8、ography .45 ISO 16380:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interes
9、ted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical C
10、ommission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documen
11、ts should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible
12、 for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for t
13、he convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL:
14、Foreword - Supplementary information The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 25, Vehicles using gaseous fuel. iv ISO 2014 All rights reserved ISO 16380:2014(E) Introduction A nozzle certified to this International Standard will be functionally compati
15、ble from a safety and performance perspective with all listed receptacles of compatible profile and system pressure. Similarly, a receptacle certified to this International Standard will be functionally compatible from a safety and performance perspective with all listed nozzles of compatible profil
16、e and system pressure. As there can eventually be many different kinds of nozzles and receptacles available from a variety of manufacturers which, for safety reasons, shall all be compatible with each other, this International Standard specifies a series of receptacle profiles. These standard profil
17、es incorporate the design specifications (mating materials, geometry, and tolerances) which can be considered in the certification of a submitted nozzle or receptacle. The construction and performance of nozzles and receptacles are based on the observation that four main parameters affect user safet
18、y and system compatibility. ISO 2014 All rights reserved v Road vehicles Blended fuels refuelling connector 1 Scope This International Standard applies to compressed blended fuels vehicle nozzles and receptacles hereinafter referred to as devices, constructed entirely of new, unused parts and materi
19、als. Compressed blended fuels fuelling connection nozzles consist of the following components, as applicable: a) Receptacle and protective cap (mounted on vehicle) (see Clause 7); b) Nozzle (mounted on dispenser side) (see Clause 5). This International Standard applies to devices which have a servic
20、e pressure of 20 MPa, 25 MPa, and 35 MPa hereinafter referred to in this International Standard as see 9.1 c): size 1: M200, M250, and M350; size 2: N200 and N250. This International Standard refers to service pressures of 20 MPa, 25 MPa, and 35 MPa for size 1 and 20 MPa and 25 MPa for size 2. This
21、International Standard applies to devices with standardised mating components (see 5.8 and 7.7). This International Standard applies to connectors which a) prevent blended fuels vehicles from being fuelled by dispenser stations with working pressures higher than the vehicle fuel system working press
22、ure, b) allow blended fuels vehicles to be fuelled by dispenser stations with working pressures equal to or lower than the vehicle fuel system working pressure, c) allow blended fuels vehicles to be fuelled by dispenser stations for compressed natural gas, d) allow blended fuels vehicles to be fuell
23、ed by compressed natural gas dispenser stations with working pressures equal to or lower than the vehicle fuel system working pressure, e) prevent blended fuels vehicles size 1 being refuelled on blended fuels dispenser stations equipped with a size 2 nozzle and vice versa, f) prevent natural gas ve
24、hicles from being fuelled by blended fuels station, and dispensers, and g) prevent pure hydrogen vehicles from being fuelled by blended fuels station dispensers. This International Standard is applicable to mixtures of hydrogen from 2 % to 30 % in volume and compressed natural gas containing: a) nat
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO163802014ROADVEHICLESBLENDEDFUELSREFUELLINGCONNECTOR 道路 车辆 混合 燃料 补充 连接器 PDF

链接地址:http://www.mydoc123.com/p-1251578.html