ISO 16293-1-2008 Glass in building - Basic soda lime silicate glass products - Part 1 Definitions and general physical and mechanical properties《建筑玻璃 碱性钙钠石英玻璃制品.pdf

《ISO 16293-1-2008 Glass in building - Basic soda lime silicate glass products - Part 1 Definitions and general physical and mechanical properties《建筑玻璃 碱性钙钠石英玻璃制品.pdf》由会员分享，可在线阅读，更多相关《ISO 16293-1-2008 Glass in building - Basic soda lime silicate glass products - Part 1 Definitions and general physical and mechanical properties《建筑玻璃 碱性钙钠石英玻璃制品.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 16293-1:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 16293-1 First edition 2008-07-01 Glass in building Basic soda lime silicate glass products Part 1: Definitions and general physical and mechanical properties Verre dans la construction Produits de base partir de verre de silica

2、te sodo-calcique Partie 1: Dfinitions et proprits physiques et mcaniques gnrales ISO 16293-1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embe

3、dded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated.

4、 Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a prob

5、lem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, inclu

6、ding photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publish

7、ed in Switzerland ii ISO 2008 All rights reservedISO 16293-1:2008(E) ISO 2008 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally

8、 carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the w

9、ork. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare Int

10、ernational Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of

11、the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16293-1 was prepared by Technical Committee ISO/TC 160, Glass in building, Subcommittee SC 1, Product considerations. ISO 16293 consists of the foll

12、owing parts, under the general title Glass in building Basic soda lime silicate glass products: Part 1: Definitions and general physical and mechanical properties A part 2 dealing with float glass is under preparation. INTERNATIONAL STANDARD ISO 16293-1:2008(E) ISO 2008 All rights reserved 1Glass in

13、 building Basic soda lime silicate glass products Part 1: Definitions and general physical and mechanical properties 1 Scope This part of ISO 16293 defines and classifies basic soda-lime silicate glass products, indicates their chemical composition, their main physical and mechanical characteristics

14、 and defines their general quality criteria. Specific dimensions and dimensional tolerances, description of faults, quality limits and designation for the product types are not included in this part of ISO 16293. NOTE It is intended to include the specific dimensions and dimensional tolerances, desc

15、ription of faults, quality limits and designation for the product types in the future ISO 16293-2, which is specific to float glass. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies.

16、 For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 9050, Glass in building Determination of light transmittance, solar direct transmittance, total solar energy transmittance, ultraviolet transmittance and related glazing factors 3 Terms and

17、 definitions For the purposes of this document, the following terms and definitions apply. 3.1 float glass flat, transparent, clear or tinted soda-lime silicate glass having parallel and polished faces obtained by continuous casting and flotation on a metal bath ISO 16293-1:2008(E) 2 ISO 2008 All ri

18、ghts reserved4 Chemical composition 4.1 General The basic glass products covered by this part of ISO 16293 are all manufactured from soda-lime silicate glass having a composition with the percent mass fraction of the major components within the following ranges: silicon dioxide (SiO 2 ) 69 % to 74 %

19、; calcium oxide (CaO) 5 % to 14 %; sodium oxide (Na 2 O) 10 % to 16 %; magnesium oxide (MgO) 0 % to 6 %; aluminium oxide (Al 2 O 3 ) 0 % to 3 %; others 0 % to 5 %. In addition to the above general composition, these glasses may also contain small quantities of other substances. 4.2 Tint Body-tinted

20、glass is obtained by the addition of suitable materials. 5 Physical and mechanical characteristics 5.1 General characteristics Conventional numerical values for the physical and mechanical characteristics of basic glass products are given in Table 1. These values, for normal, annealed glass without

21、any further toughening, are not precise requirements with which the glass shall strictly comply, but are the generally accepted figures for use in calculations where a high degree of accuracy is not required. Table 1 General characteristic values Characteristic Symbol Numerical value and unit Densit

22、y (at 18 C) 2 500 kg/m 3Hardness 6 units (Mohs scale) Youngs modulus (modulus of elasticity) E 7 10 10Pa Poissons ratio 0,2 Specific heat capacity c 0,85 10 3J/(kg K) (at 50 C) Average coefficient of linear expansion between 20 C and 300 C 9 10 6K 1Thermal conductivity 1 W/(m K) Mean refractive inde

23、x to visible radiation (380 nm to 780 nm) n 1,5 ISO 16293-1:2008(E) ISO 2008 All rights reserved 35.2 Designation of clear glass 5.2.1 General A glass product is designated as clear glass when it is not tinted and when the light transmittance of the glass material, unmodified by the possible presenc

24、e of a coating, complies with 5.2.2. In order to measure the light transmittance characteristics of glass to determine whether it can be designated as a clear glass, it is necessary, in some cases, to carry out a pre-treatment to eliminate the coatings on smooth surfaces without significantly modify

25、ing the thickness of the glass substrate. The light transmittance of the glass substrate shall be measured with its surfaces in a polished condition. Measurement shall be in accordance with ISO 9050. NOTE The light transmittance values given in 5.2.2 are not suitable for design. They are values used

26、 only for the designation of clear glass and exclude the effects of coatings. It is necessary to obtain the values of light transmittance used for design from the glass manufacturer. 5.2.2 Clear transparent glass A transparent glass product is designated as clear glass when it is not tinted and when

27、 its light transmittance, after any necessary pre-treatment and rounded to the nearest 0,01, is greater than or equal to the value given in Table 2 for the nominal thickness of the glass product. NOTE The limiting value given in Table 2 is appropriate provided that the measured thickness of the glas

28、s product is within the allowable tolerances for the nominal thickness of that product. Table 2 Minimum light transmittance values for designating a transparent glass product as clear glass Nominal thickness mm Minimum value of light transmittance 2 3 4 5 6 8 10 12 15 19 25 0,89 0,88 0,87 0,86 0,85

29、0,83 0,81 0,79 0,76 0,72 0,67 ISO 16293-1:2008(E) 4 ISO 2008 All rights reserved5.3 Stability of physical and chemical characteristics For basic glass products, the physical and chemical characteristics can be considered as remaining constant over time. a) Since glass is insensitive to photochemical

30、 effects, the spectral properties (transmission of light and solar energy) of the basic glass products are not modified by direct or indirect solar radiation. b) The surface of the glass used in building is virtually insensitive to attack from the environment. 6 General quality criteria and their ev

31、aluation 6.1 Optical quality This criterion concerns the visibility of objects observed through the glass and only applies to transparent glass products. The main faults that can affect the optical quality are distortion of the surface and lack of homogeneity in the body of the glass. The optical qu

32、ality shall be evaluated by means of a visual observation method. 6.2 Appearance This criterion concerns the appearance of the product. The visual quality can be affected by the presence of spot faults (bubbles, stones, etc.), linear/extended faults (scuff marks, scratches, lines, deposits, impressions, etc.). Spot faults are evaluated by specifying numbers and dimensions. Linear/extended faults are evaluated by visual observation. ISO 16293-1:2008(E) ICS 81.040.20 Price based on 4 pages ISO 2008 All rights reserved