ISO 15745-4-2003 Industrial automation systems and integration - Open systems application integration framework - Part 4 Reference description for Ethernet-base.pdf

《ISO 15745-4-2003 Industrial automation systems and integration - Open systems application integration framework - Part 4 Reference description for Ethernet-base.pdf》由会员分享，可在线阅读，更多相关《ISO 15745-4-2003 Industrial automation systems and integration - Open systems application integration framework - Part 4 Reference description for Ethernet-base.pdf（132页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 15745-4:2003(E) ISO 2003INTERNATIONAL STANDARD ISO 15745-4 First edition 2003-11-15 Industrial automation systems and integration Open systems application integration framework Part 4: Reference description for Ethernet-based control systems Systmes dautomatisation industrielle

2、 et intgration Cadres dintgration dapplication pour les systmes ouverts Partie 4: Description de rfrence pour les systmes de contrle fonds sur Ethernet ISO 15745-4:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printe

3、d or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liab

4、ility in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is s

5、uitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by

6、any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mai

7、l copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reservedISO 15745-4:2003(E) ISO 2003 All rights reserved iiiContents Page Forewordv Introduction vi 1 Scope1 2 Normative references1 3 Terms and definitions2 4 Abbreviated terms2 5 Technology specific elements and rul

8、es.3 5.1 Integration models and IAS interfaces 3 5.2 Profile templates3 5.2.1 General3 5.2.2 Contents and syntax3 5.2.3 Header.4 5.3 Technology specific profiles 4 6 Device and communication network profiles for Ethernet-based control systems .4 6.1 ADS-net.4 6.1.1 Device profile4 6.1.2 Communicatio

9、n network profile.6 6.2 FL-net10 6.2.1 Device profile10 6.2.2 Communication network profile.12 6.3 EtherNet/IP15 6.3.1 Device profile15 6.3.2 Communication network profile.17 Annex A (normative) ADS-net profile templates 19 A.1 General19 A.2 ADS-net device profile template description 19 A.2.1 Gener

10、al19 A.2.2 Semantics of XML schema elements.19 A.2.3 ADS-net_Device_Profile.xsd.21 A.3 ADS-net communication network profile template description23 A.3.1 General23 A.3.2 Semantics of XML schema elements.24 A.3.3 ADS-net_CommNet_Profile.xsd.28 Annex B (normative) FL-net profile templates .34 B.1 Devi

11、ce profile template description .34 B.1.1 General34 B.1.2 DeviceIdentity.34 B.1.3 DeviceManager.34 B.1.4 ApplicationProcess35 B.1.5 FL-net device profile template XML schemas.35 B.2 FL-net communication network profile template description .39 B.2.1 General39 B.2.2 ApplicationLayers39 B.2.3 Transpor

12、tLayers.40 B.2.4 NetworkManagement.40 Annex C (normative) EtherNet/IP profile templates.48 C.1 General48 ISO 15745-4:2003(E) iv ISO 2003 All rights reservedC.2 Device profile template description 49 C.2.1 Device profile template description XML based . 49 C.2.2 Device profile template description XM

13、L encapsulation of EDS files 67 C.3 Communication network profile template description 69 C.3.1 Communication network profile template description XML based. 69 C.3.2 Communication network profile template description XML encapsulation of EDS files . 82 C.4 Electronic Data Sheet (EDS) 84 C.4.1 Commo

14、n CIP EDS requirements . 84 C.4.2 EtherNet/IP specific EDS requirements 123 Bibliography . 125 ISO 15745-4:2003(E) ISO 2003 All rights reserved vForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of p

15、reparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental,

16、in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main ta

17、sk of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attenti

18、on is drawn to the possibility that some of the elements of this part of ISO 15745 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 15745-4 was prepared by Technical Committee ISO/TC 184, Industrial autom

19、ation systems and integration, Subcommittee SC 5, Architecture, communications and integration frameworks. ISO 15745 consists of the following parts, under the general title Industrial automation systems and integration Open systems application integration framework: Part 1: Generic reference descri

20、ption Part 2: Reference description for ISO 11898-based control systems Part 3: Reference description for IEC 61158-based control systems Part 4: Reference description for Ethernet-based control systems ISO 15745-4:2003(E) vi ISO 2003 All rights reservedIntroduction The application integration frame

21、work (AIF) described in ISO 15745 defines elements and rules that facilitate: the systematic organization and representation of the application integration requirements using integration models; the development of interface specifications in the form of application interoperability profiles (AIPs) t

22、hat enable both the selection of suitable resources and the documentation of the “as built“ application. ISO 15745-1 defines the generic elements and rules for describing integration models and AIPs, together with their component profiles - process profiles, information exchange profiles, and resour

23、ce profiles. The context of ISO 15745 and a structural overview of the constituents of an AIP are given in Figure 1 of ISO 15745-1:2003. This part of ISO 15745 extends the generic AIF described in ISO 15745-1 by defining the technology specific elements and rules for describing both communication ne

24、twork profiles and the communication related aspects of device profiles specific to Ethernet 1 -based control systems (ADS-net 2 , FL-net 3and EtherNet/IP 4 ). EtherNet/IP technology uses a profile of IEC 61158 which is specified in IEC 61784-1. In particular, this part of ISO 15745 describes techno

25、logy specific profile templates for the device profile and the communication network profile. Within an AIP, a device profile instance or a communication network profile instance is part of the resource profile defined in ISO 15745-1. The device profile and the communication network profile XML inst

26、ance files are included in a resource profile XML instance using the ProfileHandle_DataType as specified in ISO 15745-1:2003, 7.2.5. AIFs specified using the elements and rules of ISO 15745-1 can be easily integrated with the component profiles defined using the elements and rules specified in this

27、part. 1Ethernet is used in this document as a synonym for ISO/IEC 8802-3. 2ADS-net is a trade name used to describe JIS-TR B0012 (Autonomous Decentralized System network). This information is given for the convenience of users of ISO 15745 and does not constitute an endorsement by ISO of the tradema

28、rk, or any related products. Compliance to this standard does not require use of the trade name ADS-net. 3FL-net is a trade name used to describe JEM 1479. This information is given for the convenience of users of ISO 15745 and does not constitute an endorsement by ISO of the trademark, or any relat

29、ed products. Compliance to this standard does not require use of the trade name FL-net. 4EtherNet/IP is a trade name of ControlNet International, Ltd. and Open DeviceNet Vendor Association, Inc. This information is given for the convenience of users of ISO 15745 and does not constitute an endorsemen

30、t by ISO of the trademark holder or any of its products. Compliance to this standard does not require use of the trade name EtherNet/IP. Use of the trade name EtherNet/IP requires permission of either ControlNet International, Ltd. or Open DeviceNet Vendor Association, Inc. INTERNATIONAL STANDARD IS

31、O 15745-4:2003(E) ISO 2003 All rights reserved 1Industrial automation systems and integration Open systems application integration framework Part 4: Reference description for Ethernet-based control systems 1 Scope This part of ISO 15745 defines the technology specific elements and rules for describi

32、ng both communication network profiles and the communication related aspects of device profiles specific to Ethernet-based control systems. NOTE Generic elements and rules for describing integration models and application interoperability profiles, together with their component profiles (process pro

33、files, information exchange profiles, and resource profiles) are specified in ISO 15745-1. This part of ISO 15745 is to be used in conjunction with ISO 15745-1 to describe an application integration framework. 2 Normative references The following referenced documents are indispensable for the applic

34、ation of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 639-2:1998, Codes for the representation of names of languages Part 2: Alpha-3 code ISO 15745-1:2003, Industrial

35、 automation systems and integration Open systems application integration framework Part 1: Generic reference description ISO/IEC 7498-4:1989, Information processing systems Open Systems Interconnection Basic Reference Model Part 4: Management framework ISO/IEC 8802-3:2000, Information technology Tel

36、ecommunications and information exchange between systems Local and metropolitan area networks Specific requirements Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications ISO/IEC 10646-1:2000, Information technology Universal Multiple

37、-Octet Coded Character Set (UCS) Part 1: Architecture and Basic Multilingual Plane IEC 61158 (all parts), Digital data communications for measurement and control Fieldbus for use in industrial control systems IEC 61784-1:2003, Digital data communications for measurement and control Part 1: Profile s

38、ets for continuous and discrete manufacturing relative to fieldbus use in industrial control systems IEEE Std 754-1985 (R1990), IEEE Standard for Binary Floating Point Arithmetic JEM 1479:2002, Protocol specification Factory automation control Link Network (FL-net) JIS-TR B0012: 2000, Autonomous Dec

39、entralized System Network (ADS-net) ISO 15745-4:2003(E) 2 ISO 2003 All rights reserved REC-xml-20001006, Extensible Markup Language (XML) 1.0 Second Edition W3C Recommendation 6 October 2000 REC-xmlschema-1-20010502, XML Schema Part 1: Structures W3C Recommendation 02 May 2001 REC-xmlschema-2-200105

40、02, XML Schema Part 2: Datatypes W3C Recommendation 02 May 2001 RFC 768:1980, User Datagram Protocol Internet Engineering Task Force (IETF), Request for Comments (RFC) RFC 791:1981, Internet Protocol Internet Engineering Task Force (IETF), Request for Comments (RFC) RFC 793:1981, Transmission Contro

41、l Protocol Internet Engineering Task Force (IETF), Request for Comments (RFC) RFC 894:1984, A standard for the Transmission of IP Datagrams over Ethernet Networks Internet Engineering Task Force (IETF), Request for Comments (RFC) RFC 1738:1994, Uniform Resource Locators (URL) Internet Engineering Ta

42、sk Force (IETF), Request for Comments (RFC) RFC 1759:1995, Printer MIB Internet Engineering Task Force (IETF), Request for Comments (RFC) UML V1.4, OMG - Unified Modeling Language Specification (Version 1.4, September 2001) 3 Terms and definitions NOTE The UML terminology and notation used in this d

43、ocument is described in Annex A of ISO 15745-1:2003. For the purposes of this document, the terms and definitions given in ISO 15745-1 apply. 4 Abbreviated terms AIF Application Integration Framework AIP Application Interoperability Profile ASCII American Standard Code for Information Interchange CI

44、P 5Common Industrial Protocol EDS Electronic Data Sheet IAS Industrial Automation Systems IP Internet Protocol (see RFC 791 and RFC 894) MAC Media Access Control MCG MultiCast Group 5CIP is a trade name of ControlNet International, Ltd. and Open DeviceNet Vendor Association, Inc. This information is

45、 given for the convenience of users of ISO 15745 and does not constitute an endorsement by ISO of the trademark holder or any of its products. Compliance to this standard does not require use of the trade name CIP. Use of the trade name CIP requires permission of either ControlNet International, Ltd

46、. or Open DeviceNet Vendor Association, Inc. ISO 15745-4:2003(E) ISO 2003 All rights reserved 3 OSI Open System Interconnection TCD Transaction CoDe TCP Transmission Control Protocol (see RFC 793) UDP User Datagram Protocol (see RFC 768) UML Unified Modeling Language (see UML V1.4) XML eXtensible Ma

47、rkup Language (see REC-xml-20001006) 5 Technology specific elements and rules 5.1 Integration models and IAS interfaces The AIP developer shall develop the integration model using the rules described in ISO 15745-1, and shall ensure that the Ethernet-based device and communication network profiles (

48、whether representing the interface requirements or those derived from existing devices/communication networks) include the necessary IAS interfaces. The IAS interfaces included in the profile shall be identified in the header section (see ISO 15745-1:2003, 7.2.2). NOTE IAS interfaces are described i

49、n ISO 15745-1:2003, Annex B. 5.2 Profile templates 5.2.1 General The Ethernet based technology specific profile templates are derived from the generic profile templates specified in ISO 15745-1:2003, clause 7. 5.2.2 Contents and syntax ISO 15745 specifies profile templates that are XML schemas (REC-xmlschema-1-20010502 and REC-xmlschema- 2-20010502) and use a common general structure. The device and communication network profiles based on these templat