ISO 15031-1-2010 Road vehicles - Communication between vehicle and external equipment for emissions-related diagnostics - Part 1 General information and use cas.pdf

《ISO 15031-1-2010 Road vehicles - Communication between vehicle and external equipment for emissions-related diagnostics - Part 1 General information and use cas.pdf》由会员分享，可在线阅读，更多相关《ISO 15031-1-2010 Road vehicles - Communication between vehicle and external equipment for emissions-related diagnostics - Part 1 General information and use cas.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 15031-1:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 15031-1 Second edition 2010-12-15 Road vehicles Communication between vehicle and external equipment for emissions-related diagnostics Part 1: General information and use case definition Vhicules routiers Communications entre u

2、n vhicule et un quipement externe quant au diagnostic relatif aux missions Partie 1: Informations gnrales et dfinition de cas dusage ISO 15031-1:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but sha

3、ll not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area.

4、 Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by

5、ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any f

6、orm or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 0

7、9 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedISO 15031-1:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv Introductionvi 1 Scope1 2 Normative references1 3 Terms, definitions and abbreviated terms2 3.1 Terms and definitions .2

8、3.2 Abbreviated terms.3 4 Conventions.3 5 Document overview.4 6 Emissions-related OBD use case overview and principles 6 6.1 Overview.6 6.2 OBD use case clusters6 7 Emissions-related OBD use case definition.6 7.1 UC 1 Information about emissions-related malfunctions.6 7.1.1 UC 1.1 Information about

9、emission-related confirmed DTC(s)6 7.1.2 UC 1.2 Information about emissions-related pending DTC(s) .7 7.1.3 UC 1.3 Information about emissions-related permanent DTC(s).7 7.2 UC 2 Information related to diagnosis for the purpose of repair.8 8 Handling of new requirements.8 Bibliography9 ISO 15031-1:2

10、010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body

11、 interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotec

12、hnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by

13、the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent righ

14、ts. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15031-1 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3, Electrical and electronic equipment. This second edition cancels and replaces the first edition (ISO 15031-1:2001), which

15、has been technically revised. ISO 15031 consists of the following parts, under the general title Road vehicles Communication between vehicle and external equipment for emissions-related diagnostics: Part 1: General information and use case definition Part 2: Guidance on terms, definitions, abbreviat

16、ions and acronyms Part 3: Diagnostic connector and related electrical circuits, specification and use Part 4: External test equipment Part 5: Emissions-related diagnostic services Part 6: Diagnostic trouble code definitions Part 7: Data link security ISO 15031 provides an implementer with all docume

17、nts and references required to support the implementation of legislated on-board diagnostics (OBDs) in accordance with the requirements set forth in the country-specific emissions regulation. ISO 15031-1 provides general information and use case definitions and an overview of the document set along

18、with the use case definitions and a common set of resources (definitions, references) for use by all subsequent parts. ISO 15031-2 is a guide to terms, definitions, abbreviations and acronyms used in emissions-related diagnostics, with respect to the communication between road vehicles and external

19、equipment used in that field. It also specifies a procedure for constructing new terms. As it gives recommended usage of diagnostic terms applicable to electrical/electronic systems, it also makes reference to related mechanical terms, definitions, abbreviations and acronyms. ISO 15031-1:2010(E) ISO

20、 2010 All rights reserved v ISO 15031-3 specifies a minimum set of requirements for a diagnostic connector used in communication between vehicle and external equipment for emissions-related diagnostics. ISO 15031-4 provides requirements to be fulfilled by any external test equipment connected to the

21、 vehicle. ISO 15031-5 provides the data reporting requirements of (OBD) regulations in the United States and Europe, and any other region that may adopt similar requirements in the future. ISO 15031-5 specifies: message formats for request and response messages, timing requirements between request m

22、essages from external test equipment and response messages from vehicles, and between those messages and subsequent request messages, behaviour of both the vehicle and external test equipment if data is not available, a set of diagnostic services, with corresponding content of request and response m

23、essages, to satisfy OBD regulations. ISO 15031-6 provides uniformity for standardized Diagnostic Trouble Codes (DTC) that electrical/electronic (OBD) systems of motor vehicles are required to report when malfunctions are detected. It further provides guidance for uniform messages (text descriptor) a

24、ssociated with these codes. ISO 15031-7 specifies a standard mechanism for limiting access to particular vehicle services (such as those intended for use only within the original manufacturing plant). ISO 15031-1:2010(E) vi ISO 2010 All rights reservedIntroduction 0.1 Overview ISO 15031 consists of

25、a number of parts which, taken together, provide a coherent, self-consistent set of specifications to facilitate emissions-related diagnostics. Parts 2 through 7 are based on SAE recommended practices. This part of ISO 15031 provides an introduction to the series of International Standards and the r

26、eference to the SAE Digital Annexes (DA). Such standardization is of benefit to many sectors of the automotive industry, including service technicians who are required to work on a variety of vehicle types and component suppliers who wish to provide similar products to several vehicle manufacturers.

27、 Some of the documents have a wider scope than just purely emissions-related issues. The legislator is the adequate authority to make the appropriate references. ISO 15031 includes the communication between the vehicles on-board diagnostic (OBD) systems and an external (off-board) “generic” test equ

28、ipment within the scope of the emissions-related OBD legislation. To achieve this, it is based on the Open Systems Interconnection (OSI) Basic Reference Model in accordance with ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers. When mapped on this model, the

29、 services specified by ISO 15031 are broken into the following layers in accordance with Table 1: diagnostic services (layer 7), specified in ISO 15031-5 (emissions-related OBD); ISO 27145-3 (WWH-OBD); presentation layer (layer 6), specified in ISO 15031-2, SAE J1930-DA; ISO 15031-5, SAE J1979-DA; I

30、SO 15031-6, SAE J2012-DA (OBD); ISO 27145-2, SAE J2012-DA (WWH-OBD); session layer services (layer 5), specified in ISO 14229-2 support ISO 15765-4 and ISO 14230-4 protocol; ISO 14229-2 are not applicable to the SAE J1850 and ISO 9141-2 protocols; transport layer services (layer 4), specified in ISO

31、 15765-4, ISO 15765-2 Transport protocol and network layer services; SAE J1850 defined in ISO 15031-5; ISO 9141-2 defined in ISO 15031-5; ISO 14230-4 defined in ISO 15031-5; ISO 15031-1:2010(E) ISO 2010 All rights reserved vii network layer services (layer 3), specified in ISO 15765-4, ISO 15765-2 T

32、ransport protocol and network layer services; SAE J1850 defined in ISO 15031-5; ISO 9141-2 defined in ISO 15031-5; ISO 14230-4 defined in ISO 15031-5; data link layer (layer 2), specified in ISO 15765-4, ISO 11898-1 and ISO 11898-2; SAE J1850; ISO 9141-2; ISO 14230-2; physical layer (layer 1), speci

33、fied in ISO 15765-4, ISO 11898-1 and ISO 11898-2; SAE J1850; ISO 9141-2; ISO 14230-1. Table 1 Legislated emissions-related OBD/WWH 1) -OBD diagnostic specifications applicable to the OSI layers Applicability OSI 7 layers Emissions-related OBD communication requirements Emissions-related WWH-OBD comm

34、unication requirements Application (layer 7) ISO 15031-5 ISO 27145-3 ISO 15031-2, ISO 15031-5, ISO 15031-6 SAE J1930-DA / SAE J1979-DA ISO 27145-2 SAE J1930-DA / SAE J1979-DA Presentation (layer 6) SAE J2012-DA (OBD) SAE J2012-DA (WWH-OBD) Session (layer 5) Not Applicable ISO 14229-2 Transport (laye

35、r 4) Network (layer 3) ISO 15031-5 ISO 14230-4 ISO 15765-2 ISO 15765-2 ISO 13400-2 Data link (layer 2) ISO 14230-2 Seven layer according to ISO/IEC 7498-1 and ISO/IEC 10731 Physical (layer 1) SAE J1850 ISO 9141-2 ISO 14230-1 ISO 11898-1, ISO 11898 -2 ISO 15765-4 ISO 11898-1, ISO 11898 -2 ISO 27145-4

36、 ISO 13400-31) World-Wide Harmonized. ISO 15031-1:2010(E) viii ISO 2010 All rights reserved0.2 SAE document reference concept ISO 15031 references several SAE documents which contain all terms, data and DTC (diagnostic trouble code) definitions. This is illustrated in Figure 1. Additional informatio

37、n on the content of the referenced documents is given below: SAE J1930: the document is concerned with a procedure for naming objects and systems and with the set of words from which names are built. It references SAE J1930-DA, which contains all standardized naming objects, terms and abbreviations.

38、 SAE J1979: the document is concerned with the definition of emissions-related diagnostic services (diagnostic test modes). It references SAE J1979-DA, which contains all standardized data items like PIDs, Test Ids, Monitor Ids and InfoType Ids. SAE J2012: the document is concerned with the procedur

39、e for defining emissions-related DTCs. It references SAE J2012-DA, which contains all standardized data items like DTCs and FTBs. SAE J1979-DA Emissions-related data definition SAE J2012-DA OBD Emissions-related diagnostic trouble code definition SAE J1930-DA Emissions-related acronym definition ISO

40、 15031-2 Terms, definitions, abbreviations and acronyms ISO 15031-5 Emissions-related diagnostic services ISO 15031-6 Diagnostic trouble code (DTC) definitions SAE J1930 Terms, definitions abbreviations and acronyms SAE J1979 Emissions-related diagnostic services SAE J2012 Diagnostic trouble code (D

41、TC) definitions 1Key 1 SAE Digital Annexes Figure 1 SAE Digital Annex document reference 0.3 SAE Digital Annex revision procedure New emissions-related regulatory requirements drive new in-vehicle technology to lower emissions. New technology-related OBD monitor data and DTCs need to be standardized

42、 to support the external (off-board) “generic” test equipment. All relevant information is proposed by the automotive industry represented by members of the appropriate SAE task force. ISO 15031-1:2010(E) ISO 2010 All rights reserved ixISO 15031-2, ISO 15031-5 and ISO 15031-6 reference a “Change Req

43、uest Form” to be used for new data items to be defined by the SAE task force for standardization. The standardized data items will be defined in SAE J1930-DA, SAE J1979-DA and SAE J2012-DA. Once the information has been balloted and approved the documents will be published on the SAE Store Web Site.

44、 The revision request forms and instructions for updating the registers to all parts of ISO 15031 can be obtained on the Registration Authoritys website at: for Part 2: http:/www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS7 The column titled “Resources” shows a document with the title: J193

45、0-DA_Revision_Request_Form.doc. Double click on the name and you will be asked to download the document with the filename: SAE_J1930-DA_Revision_Request_Form.doc for Part 5: http:/www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS14 The column titled “Resources” shows a document with the title

46、: J1979-DA_Revision_Request_Form.doc. Double click on the name and you will be asked to download the document with the filename: SAE_J1979-DA_Revision_Request_Form.doc for Part 6: http:/www.sae.org/servlets/works/committeeHome.do?comtID=TEVDS9 The column titled “Resources” shows a document with the

47、title: J2012-DA_Revision_Request_Form.doc. Double click on the name and you will be asked to download the document with the filename: SAE_J2012-DA_Revision_Request_Form.doc Fill out the revision request form with your request. Please send an email with the completed revision request form as an attac

48、hment to: SAE Headquarters 755 West Big Beaver Road Suite 1600 Troy, MI 48084-4093, USA Fax: +1 (248) 273-2494 Email: saej1930sae.org Email: saej1979sae.org Email: saej2012sae.org INTERNATIONAL STANDARD ISO 15031-1:2010(E) ISO 2010 All rights reserved 1Road vehicles Communication between vehicle and

49、 external equipment for emissions-related diagnostics Part 1: General information and use case definition 1 Scope This part of ISO 15031 gives an overview of the structure and the partitioning of ISO 15031, and shows the relation between the different parts. It also defines the corresponding SAE recommended practices and reference to the SAE Digital Annexes. The terminology defined in this part of ISO