ISO 14313 CORR 1-2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves Technical Corrigendum 1《石油和天然气工业 管道运输系统 管道阀 技术勘误1.pdf

《ISO 14313 CORR 1-2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves Technical Corrigendum 1《石油和天然气工业 管道运输系统 管道阀 技术勘误1.pdf》由会员分享，可在线阅读，更多相关《ISO 14313 CORR 1-2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves Technical Corrigendum 1《石油和天然气工业 管道运输系统 管道阀 技术勘误1.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、ICS 75.200 Ref. No. ISO 14313:2007/Cor.1:2009(E) ISO 2009 All rights reserved Published in Switzerland INTERNATIONAL STANDARD ISO 14313:2007 TECHNICAL CORRIGENDUM 1 Published 2009-01-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATIONPetroleum and natural g

2、as industries Pipeline transportation systems Pipeline valves TECHNICAL CORRIGENDUM 1 Industries du ptrole et du gaz naturel Systmes de transport par conduites Robinets de conduites RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to ISO 14313:2007 was prepared by Technical Committee ISO/TC 67, Mate

3、rials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 2, Pipeline transportation systems. Pages 2 to 3, Clause 3 Replace the following normative references: “ASME B16.5-1996, Pipe Flanges and Flanged Fittings: NPS 1/2 through 24” with “ASME

4、 B16.5-2003, Pipe Flanges and Flanged Fitting : NPS 1/2 through 24” “ASME B31.8-2003, Gas Transmission and Distribution Piping Systems” with “ASME B31.8-2007, Gas Transmission and Distribution Piping Systems” “ASME Boiler and Pressure Vessel Code Section VIII: Rules for Construction of Pressure Vess

5、els Division 2: Alternative Rules” with “ASME Boiler and Pressure Vessel Code Section VIII: Rules for Construction of Pressure Vessels Division 2-2004: Alternative Rules” ISO 14313:2007/Cor.1:2009(E) 2 ISO 2009 All rights reservedPage 34, Table 4, under subheading “PN 50 (class 300)”, line for “DN 1

6、50 (NPS 6)” Replace the value of “457” in the column “Raised face (A) ” by “403” such that the line reads: 150 6 403 457 419 Page 36, Table 4, under subheading “PN 420 (class 2 500)”, line for “DN 65 (NPS 2-1/2)” Replace the value of “540” in the column “Ring joint” by “514” such that the line reads

7、: 65 2-1/2 508 508 514 Page 41, 7.7.2 Replace “ASME B31.8-2003” with “ASME B31.8-2007”. Replace “Figure 14 and 15” with “Figures I4 and I5”. Page 45, 7.20.2, second sentence Replace “ASME Code Section VIII, Division 2, Part AD-132” with “ASME Code Section VIII, Division 2-2004, Part AD-132”. Page 49

8、, 9.3 Delete the words “by agreement” from the NOTE. Page 49, 9.4, second paragraph, second sentence Add “pipe pups to valve” after “Repairs of fabrication welds”. Page 63, B.3.3 Replace “0,55 MPa 00,7 MPa” with “0,55 MPa 0,07 MPa”. Page 71, Table D.1, beginning of last box Replace “Other requirements” with “Other requirements”. Page 71, Table D.1, after “ISO 15156 (all parts)? Yes _ No _”, add the following line “If yes, specify % mass fraction of H 2 S _; pH _; % mass fraction of chlorides _; temperature _”