ISO 12643-3-2010 Graphic technology - Safety requirements for graphic technology equipment and systems - Part 3 Binding and finishing equipment and systems《图形技术.pdf
《ISO 12643-3-2010 Graphic technology - Safety requirements for graphic technology equipment and systems - Part 3 Binding and finishing equipment and systems《图形技术.pdf》由会员分享,可在线阅读,更多相关《ISO 12643-3-2010 Graphic technology - Safety requirements for graphic technology equipment and systems - Part 3 Binding and finishing equipment and systems《图形技术.pdf(64页珍藏版)》请在麦多课文档分享上搜索。
1、 Reference number ISO 12643-3:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 12643-3 Second edition 2010-12-15 Graphic technology Safety requirements for graphic technology equipment and systems Part 3: Binding and finishing equipment and systems Technologie graphique Exigences de scurit pour les systme
2、s et lquipement de technologie graphique Partie 3: Systmes et quipement de reliure et de finissage ISO 12643-3:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefa
3、ces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Sys
4、tems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely
5、 event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or
6、 mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web w
7、ww.iso.org Published in Switzerland ii ISO 2010 All rights reservedISO 12643-3:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Conformity with this part of ISO 12643 .5 5 Guarding of significant hazards 5
8、5.1 General .5 5.2 Interlocks5 5.3 Guarding of hoppers and hopper feeders 6 5.4 Guarding on binding and finishing machines6 5.5 Inserting and collating machines 23 5.6 Counter-stackers.23 5.7 Paper-embossing machines.24 5.8 Finishing machines.25 5.9 Guillotine cutters.31 5.10 Trimmers 42 5.11 Onsert
9、ers/attaching machines.43 5.12 Overcover/protective wrapper gluers43 5.13 Corner-rounding machines 43 6 Information for use44 6.1 Minimum requirements for machine markings 44 6.2 Contents of instruction handbook.44 Annex A (informative) Hazards associated with binding and finishing equipment and sys
10、tems48 Annex B (informative) Protection zones against explosion .54 Bibliography56 ISO 12643-3:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing In
11、ternational Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison
12、with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of techn
13、ical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn
14、 to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12643-3 was prepared by Technical Committee ISO/TC 130, Graphic technology. This second edition of ISO 12643-3 cons
15、titutes a technical revision of the first edition (ISO 12643-3:2008). Significant changes incorporated into this second edition include, but are not limited to, updated requirements for performance levels (PL) or safety integrity levels (SIL) as defined in the current version of ISO 13849-1 and IEC
16、62061, respectively. It is the intent of ISO/TC 130 that both the first and second editions of ISO 12643-3 be applicable until 2011-12-31. ISO 12643-3:2008 is thus provisionally retained until this date. As from 2012-01-01, ISO 12643-3:2010 will cancel and replace ISO 12643-3:2008. Accordingly, as f
17、rom 2012-01-01, only ISO 12643-3:2010 will be applicable to new equipment manufactured. ISO 12643 consists of the following parts, under the general title Graphic technology Safety requirements for graphic technology equipment and systems: Part 1: General requirements Part 2: Prepress and press equi
18、pment and systems Part 3: Binding and finishing equipment and systems Part 4: Converting equipment and systems Part 5: Stand-alone platen presses ISO 12643-3:2010(E) ISO 2010 All rights reserved vIntroduction During the development of this part of ISO 12643, existing relevant standards of other coun
19、tries were taken into consideration. An effort has been made to harmonize the requirements of all countries, recognizing that national standards or laws may dictate national requirements. In cases where it was known that there is a national requirement that differs from this part of ISO 12643, that
20、has been noted. This part of ISO 12643 was developed to harmonize the requirements of the following US and European safety standards: ANSI B65.2, Graphic technology Safety requirements for binding and finishing systems and equipment ANSI B65.3, Safety standard Guillotine paper cutters, mill trimmers
21、 and integral handling equipment ANSI B65.4, Safety standard Three-knife trimmers including rotary, and single- and multiple-knife trimmers EN 1010-1, Safety of machinery Safety requirements for the design and construction of printing and paper converting machines Part 1: Common requirements EN 1010
22、-3, Safety of machinery Safety requirements for the design and construction of printing and paper converting machines Part 3: Cutting machines EN 1010-4, Safety of machinery Safety requirements for the design and construction of printing and paper converting machines Part 4: Bookbinding, paper conve
23、rting and finishing machines INTERNATIONAL STANDARD ISO 12643-3:2010(E) ISO 2010 All rights reserved 1Graphic technology Safety requirements for graphic technology equipment and systems Part 3: Binding and finishing equipment and systems 1 Scope This part of ISO 12643 provides safety requirements sp
24、ecific to binding and finishing equipment and systems. It is intended to be used in conjunction with the general requirements given in ISO 12643-1. This part of ISO 12643 provides additional safety requirements for the design and construction of new equipment used to convert printed or blank substra
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO1264332010GRAPHICTECHNOLOGYSAFETYREQUIREMENTSFORGRAPHICTECHNOLOGYEQUIPMENTANDSYSTEMSPART3BINDINGANDFINISHINGEQUIPMENTANDSYSTEMS

链接地址:http://www.mydoc123.com/p-1250545.html