ISO 11677-3-1995 Textile machinery and accessories - Main dimensions of open end loop flat steel healds and their corresponding heald-carrying rods - Part 3 Car.pdf

《ISO 11677-3-1995 Textile machinery and accessories - Main dimensions of open end loop flat steel healds and their corresponding heald-carrying rods - Part 3 Car.pdf》由会员分享，可在线阅读，更多相关《ISO 11677-3-1995 Textile machinery and accessories - Main dimensions of open end loop flat steel healds and their corresponding heald-carrying rods - Part 3 Car.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD ISO 11677-3 First edition 1995-12-01 Textile machinery and accessories - Main dimensions of open end loop flat steel healds and their corresponding heald-carrying rods - Part 3: Carrying rods for healds with C- and J-shaped end loops Materie/ pour Iindustrie textile - Dimensio

2、ns principales des lisses en acier plat avec boucles dextr6mites ouvertes et des tringles porte-lisses correspondan tes - Partie 3: Tringles porte-lisses pour lisses avec boucles dextrkmith en forme de (4) et l(J) Reference number ISO 11677-3: 1995(E) Copyright International Organization for Standar

3、dization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 11677=3:1995(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bodies). The work

4、 of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmen

5、tal, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (1 EC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for votin

6、g. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 11677-3 was prepared by Technical Committee ISO/TC 72, and accessories Textile machinery and allied machinery, Sub- committee SC 3, Machinery for fabric manu

7、facture. This first edition of ISO 11677-3 cancels and replaces the first edition of ISO 6457:1982, which has been technically revised. ISO 11677 consists of the following Parts, under the general title Textile machinery and accessories - Main dimensions of open end loop flat s teel healds and their

8、 corresponding heald-carrying rods: - Part 1: C-shaped end loops - Part 2: J-shaped end loops - Part 3: Carrying rods for healds with C- and J-shaped end loops The general titles of Parts 1 and 2 will be aligned with the general title of Part 3 at their next revisio n. 0 ISO 1995 All rights reserved

9、. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronrc or mechanical, including photocopying and mrcrofilm, without Permission in writing from the publisher. lnternational Organization for Standardization Case Postale 56 l CH-l

10、 211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNATIONAL STANDARD 0 ISO ISO 11677=3:1995(E) Textile machinery

11、and accessories - Main dimensions of open end loop flat steel healds and their corresponding heald-carrying rods - Part 3: Carrying rods for healds with C- and J-shaped end loops 1 Scope This part of ISO 11677 specifies the main dimensions and designation of heald-carrying rods for C- and J- shaped

12、end loops of flat steel healds which are in ac- cordante with ISO 11677-1 and ISO 11677-2 respectively. 2 Normative references The following Standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 11677. At the time of publication, the editions i

13、ndicated were valid. All Standards are subject to revision, and Parties to agreements based on this part of ISO 11677 are encouraged to investi- gate the possibility of applying the most recent edi- tions of the Standards indicated below. Members of IEC and ISO maintain registers of currently valid

14、International Standards. ISO 11677-1: 1994, Textile machinery and accessories - Main dimensions of flat steel healds with open end loops - Part 1: C-shaped end loops. ISO 11677-2:1994, Textile machinery and accessories - Main dimensions of flat steel healds with open end loops - Part 2: J-shaped end

15、 loops. 3 Dimensions The main dimensions of heald-carrying rods for flat steel healds with C- and J-shaped end loops shall be as shown in figures 1 and 2 respectively. 4 Designation Example of designation for a heald-carrying rod for flat steel healds with C-shaped end loops: Heald-carrying rod ISO

16、11677-3 - C Example of designation for a heald-carrying rod for flat steel healds with J-shaped end loops: Heald-carrying rod ISO 11677-3 - J Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without l

17、icense from IHS-,-,-ISO 11677-3: 1995(E) 0 ISO 0 3 I 1 i ; (-j 1 1, , 1 c-, IJ - - Dimensions in millimetres Figure 1 - Cross-section of heald-carrying rod for flat steel healds with C-shaped end loops Dimensions in millimetres Figure 2 - Cross-section of heald-carrying rod for flat steel healds wit

18、h J-shaped end loops Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided

19、by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted with

20、out license from IHS-,-,-This page intentionally left blank Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ISO 1167703:1995(E) llcs 59.120.30 Descriptors: textile machin

21、ery, weaving machinery, accessories, steel products, healds, bar-s (textile), dimensions, designation. Price based on 2 pages Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-