API MPMS 19 1-2012 Manual of Petroleum Measurement Standards Chapter 19 1 Evaporative Loss From Fixed-Roof Tanks (Fourth Edition)《石油计量标准手册 第19 1章 固定罐顶蒸发损失 第4版》.pdf

《API MPMS 19 1-2012 Manual of Petroleum Measurement Standards Chapter 19 1 Evaporative Loss From Fixed-Roof Tanks (Fourth Edition)《石油计量标准手册 第19 1章 固定罐顶蒸发损失 第4版》.pdf》由会员分享，可在线阅读，更多相关《API MPMS 19 1-2012 Manual of Petroleum Measurement Standards Chapter 19 1 Evaporative Loss From Fixed-Roof Tanks (Fourth Edition)《石油计量标准手册 第19 1章 固定罐顶蒸发损失 第4版》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、Manual of Petroleum Measurement Standards Chapter 19.1 Evaporative Loss From Fixed-Roof Tanks FOURTH EDITION, OCTOBER 2012Manual of Petroleum Measurement Standards Chapter 19.1 Evaporative Loss From Fixed-Roof Tanks Measurement Coordination FOURTH EDITION, OCTOBER 2012Special Notes API publications

2、necessarily address problems of a general nature. With respect to particular circumstances, local, state, and federal laws and regulations should be reviewed. Neither API nor any of APIs employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, eithe

3、r express or implied, with respect to the accuracy, completeness, or usefulness of the information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of APIs employees,

4、subcontractors, consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights. API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in

5、 them; however, the Institute makes no representation, warranty, or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publi

6、cation may conflict. API publications are published to facilitate the broad availability of proven, sound engineering and operating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilize

7、d. The formulation and publication of API publications is not intended in any way to inhibit anyone from using any other practices. Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applica

8、ble requirements of that standard. API does not represent, warrant, or guarantee that such products do in fact conform to the applicable API standard. Users of this standard should not rely exclusively on the information contained in this document. Sound business, scientific, engineering, and safety

9、 judgment should be used in employing the information contained herein. All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission

10、from the publisher. Contact the Publisher, API Publishing Services, 1220 L Street, NW, Washington, DC 20005. Copyright 2012 American Petroleum InstituteForeword Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale,

11、or use of any method, apparatus, or product covered by letters patent. Neither should anything contained in the publication be construed as insuring anyone against liability for infringement of letters patent. Shall: As used in a standard, “shall” denotes a minimum requirement in order to conform to

12、 the specification. Should: As used in a standard, “should” denotes a recommendation or that which is advised but not required in order to conform to the specification. This document was produced under API standardization procedures that ensure appropriate notification and participation in the devel

13、opmental process and is designated as an API standard. Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petrol

14、eum Institute, 1220 L Street, NW, Washington, DC 20005. Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director. Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years.

15、A one-time extension of up to two years may be added to this review cycle. Status of the publication can be ascertained from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 1220 L Street, NW, Washington, DC 20005. Sugg

16、ested revisions are invited and should be submitted to the Standards Department, API, 1220 L Street, NW, Washington, DC 20005, standardsapi.org. iiiSummary of Changes to API MPMS Chapters 19.1, 19.2 and 19.4 The third edition of API Manual of Petroleum Measurement Standards (MPMS) Chapter 19.4 was p

17、ublished following a revision that was carried out concurrently with revisions to Chapter 19.1, published as the fourth edition, and Chapter 19.2, published as the third edition. Primary changes are: 1) Consolidation of common material in Chapter 19.4. Material that had previously been included in b

18、oth Chapters 19.1 and 19.2 has been moved to Chapter 19.4. Chapter 19.4, which was previously Recommended Practice for Speciation of Evaporative Losses, now has the title Evaporative Loss Reference Information and Speciation Methodology. This Chapter had already contained reference information on th

19、e properties of chemicals and typical petroleum liquids, and this information has now been removed from Chapters 19.1 and 19.2. In addition, meteorological data have been moved from Chapters 19.1 and 19.2 to Chapter 19.4. In the revised documents: a) Meteorological data are found in Chapter 19.4, b)

20、 Calculation of storage tank temperatures is found in Chapters 19.1 and 19.2 (in that fixed-roof tanks involve calculation of the vapor space temperature in order to determine vapor density, whereas this step is not involved in estimating emissions from floating-roof tanks), and c) Calculation of tr

21、ue vapor pressure is found in Chapter 19.4 (in that this is now calculated in the same manner for both fixed- and floating-roof tanks). 2) Reconciliation of nomenclature. Chapters 19.1 and 19.2 previously had different nomenclature for the same variables. These revisions adopt a common set of symbol

22、s for both chapters. 3) Reorganization of the formats. In addition to common material having been removed from Chapters 19.1 and 19.2, the remaining text has been edited to remove unnecessarily verbose or repetitive language. The summary tables were deemed redundant, and have been deleted. 4) Append

23、ices. Appendices have been redesignated as annexes. 5) SI units. An annex has been added to each chapter to address SI units. Chapter 19.1, fourth edition In addition to common reference material being deleted from Chapter 19.1, the following changes have been made: 1) Reference to API Technical Rep

24、orts. References to API TR 2568 (cleaning storage tanks) and API TR 2569 (closed vent IFRTs) have been added. 2) Terminology. The following terminology has been revised: a) “Standing storage loss” has been changed to “standing loss.” b) “Solar insolation” has been changed to “insolation.” 3) Effecti

25、ve Throughput. An expression has been added for the sum of changes in liquid level, designated H Q , for calculating effective throughput. 4) Normal operating pressure. An expression has been added for calculating the normal operating pressure, as the average of the maximum and minimum vent settings

26、. 5) Vapor density from vapor space temperature. The temperature used in the calculation of vapor density has been changed from the liquid surface temperature to the vapor space temperature, and an equation has been added for determining the vapor space temperature. vContents Page 1 Scope . . . . .

27、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Normative References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28、. . . . . . . . 1 3 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 Procedure for Estimating Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29、. . . . . . . . . . . . . . . . . . . . . . 3 4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4.2 Standing Loss L S . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4.3 Working Loss L W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Example . . . . . . . . . . . . . . .

31、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.1 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32、 11 5.2 Solution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6 Equipment Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

33、. . . . . . . . . . . . . . . . . . 13 6.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6.2 Fixed-Roof Tanks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.3 Roof Fittings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6.4 Insulation . . . . . . . . . . . . . . . .

35、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.5 Outside Surfaces of the Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7 Loss Mechani

36、sms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37、 . . . . . . . . . . 16 7.2 Standing Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7.3 Working Loss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

38、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 8 Development of Estimation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 8.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 8.2 Standing Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 8.3 Working Loss. . . . . . . . . . . . . . .

40、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Annex A (informative) SI units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Bibliograp

41、hy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figures 1 Fixed-Roof Tank Geometry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

42、. . . . . . . . . . . . . . . 5 2 Typical Fixed-Roof Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 vii1 Chapter 19.1Evaporative Loss From Fixed-Roof Tanks 1 Scope This standard contains methodologies for es

43、timating the total evaporative losses of hydrocarbons from fixed- roof tanks. The methodologies provide loss estimates for general equipment types based on laboratory, test- tank and field-tank data. Types of fixed-roof tanks and roof fittings described are for information only. The equations estima

44、te average annual losses from uninsulated fixed-roof tanks for various liquid stocks, stock vapor pressures, tank sizes, meteorological conditions, and operating conditions. The following special cases are addressed: a) Horizontal tanks. b) Higher volatility stocks (true vapor pressure greater than

45、0.1 psia). c) Vent settings higher than 0.03 psia (0.5 oz/in 2 ). The estimation may be improved by using detailed field information, including climatic data and operational data for the appropriate time period. The equations are not intended to be used in the following applications: a) To estimate

46、losses from unstable or boiling stocks or from petroleum liquids or petrochemicals for which the vapor pressure is not known or cannot readily be predicted (to calculate emissions from tanks that contain material at or above their boiling point or the point at which material starts to flash, the API

47、 model E&P Tank (API Publication 4697) can be used). b) To estimate losses from fixed-roof tanks which have an internal floating roof. API MPMS Ch. 19.2 4and API TR 2569 13address these. c) To estimate losses from fixed-roof tanks which have either roof or shell insulation. d) To estimate losses fro

48、m cleaning fixed-roof tanks. API TR 2568 12addresses this. The estimation procedures were developed to provide estimates of typical losses from fixed-roof tanks that are properly maintained and in normal working condition. Losses from poorly maintained tanks may be greater. Because the loss equation

49、s are based on equipment conditions that represent a large population of tanks, a loss estimate for a group of fixed-roof tanks may be more representative than a loss estimate for an individual tank. Evaporative loss considerations are not the only criteria for equipment selection. Many other factors not addressed in this standard, such as tank operation, maintenance, and safety, are important in designing and selecting tank equipment for a given application. 2 Normative References The following referenced documents are indispensable for the application of this document. For dated