ACI 228 2R-2013 Report on Nondestructive Test Methods for Evaluation of Concrete in Structures.pdf

《ACI 228 2R-2013 Report on Nondestructive Test Methods for Evaluation of Concrete in Structures.pdf》由会员分享，可在线阅读，更多相关《ACI 228 2R-2013 Report on Nondestructive Test Methods for Evaluation of Concrete in Structures.pdf（86页珍藏版）》请在麦多课文档分享上搜索。

1、ACI 228.2R-13Report on Nondestructive Test Methods for Evaluation of Concrete in StructuresReported by ACI Committee 228First PrintingJune 2013Report on Nondestructive Test Methods for Evaluation of Concrete in Structures Copyright by the American Concrete Institute, Farmington Hills, MI. All rights

2、 reserved. This material may not be reproduced or copied, in whole or part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of ACI.The technical committees responsible for ACI committee reports and standards strive to avoid ambiguiti

3、es, omissions, and errors in these documents. In spite of these efforts, the users of ACI documents occasionally find information or requirements that may be subject to more than one interpretation or may be incomplete or incorrect. Users who have suggestions for the improvement of ACI documents are

4、 requested to contact ACI via the errata website at www.concrete.org/committees/errata.asp. Proper use of this document includes periodically checking for errata for the most up-to-date revisions.ACI committee documents are intended for the use of individuals who are competent to evaluate the signif

5、icance and limitations of its content and recommendations and who will accept responsibility for the application of the material it contains. Individuals who use this publication in any way assume all risk and accept total responsibility for the application and use of this information.All informatio

6、n in this publication is provided “as is” without warranty of any kind, either express or implied, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose or non-infringement.ACI and its members disclaim liability for damages of any kind, including a

7、ny special, indirect, incidental, or con-sequential damages, including without limitation, lost revenues or lost profits, which may result from the use of this publication.It is the responsibility of the user of this document to establish health and safety practices appropriate to the specific circu

8、mstances involved with its use. ACI does not make any representations with regard to health and safety issues and the use of this document. The user must determine the applicability of all regulatory limitations before applying the document and must comply with all applicable laws and regulations, i

9、ncluding but not limited to, United States Occupational Safety and Health Administration (OSHA) health and safety standards.Participation by governmental representatives in the work of the American Concrete Institute and in the develop-ment of Institute standards does not constitute governmental end

10、orsement of ACI or the standards that it develops.Order information: ACI documents are available in print, by download, on CD-ROM, through electronic subscription, or reprint and may be obtained by contacting ACI.Most ACI standards and committee reports are gathered together in the annually revised

11、ACI Manual of Concrete Practice (MCP).American Concrete Institute38800 Country Club DriveFarmington Hills, MI 48331U.S.A.Phone: 248-848-3700Fax: 248-848-3701www.concrete.orgISBN-13: 978-0-87031-820-7ISBN: 0-87031-820-9American Concrete InstituteAdvancing concrete knowledgeA review is presented of no

12、ndestructive test (NDT) methods for evaluating the condition of concrete and steel reinforcement in structures. Methods discussed include visual inspection, stress-wave, nuclear, measurement of fluid transport properties, magnetic and electrical, infrared thermography, and ground-penetrating radar.

13、The principle of each method is discussed and the typical instrumentation described. Testing procedures are summarized and the data analysis methods explained. The advantages and limita-tions of the methods are highlighted. This report concludes with a discussion of planning a NDT program. General i

14、nformation is provided for those faced with the task of evaluating the condition of a concrete structure and who are considering the applicability of NDT methods to aid in that evaluation.Keywords: covermeter; deep foundations; half-cell potential; infrared thermography; nondestructive testing; pola

15、rization resistance; radar; radi-ography; radiometry; stress-wave methods; transport properties; visual inspection.ContentsCHAPteR 1IntRoDUCtIon, p. 21.1Scope, p. 21.2Needs and applications, p. 21.3Objective, p. 2CHAPteR 2notAtIon AnD DeFInItIons, p. 22.1Notation, p. 22.2Definitions, p. 3CHAPteR 3sU

16、MMARY oF MetHoDs, p. 33.1Visual inspection, p. 53.2Stress-wave methods for structures, p. 63.3Low strain stress-wave methods for deep founda-tions, p. 173.4Nuclear methods, p. 233.5Magnetic and electrical methods, p. 283.6Methods for measuring transport properties, p. 443.7Infrared thermography, p.

17、513.8Radar, p. 53CHAPteR 4PLAnnInG AnD PeRFoRMInG nonDestRUCtIVe testInG InVestIGAtIons, p. 614.1Selection of methods, p. 614.2Defining scope of investigation, p. 62ACI 228.2R-13Report on nondestructive test Methods for evaluation of Concrete in structuresReported by ACI Committee 228Michael C. Ford

18、e, Chair Bernard H. Hertlein, SecretaryMuhammed P. A. Basheer Jacob K. BiceAndrew J. BoydMichael BrownHonggang Cao Nicholas J. Carino William CiggelakisNeil A. CummingAldo De La Haza Ethan C. DodgeBoris DragunskyChristopher C. Ferraro Frederick D. Heidbrink Kal R. HindoRobert S. Jenkins Keith E. Kes

19、nerH. S. LewMalcolm K. LimKenneth M. LozenLarry D. OlsonStephen Pessiki John S. Popovics Randall W. Poston Paul L. Siwek Patrick J. E.SullivanConsulting membersJohn H. BungeyHermenegildo CaratinGerardo G. ClemenaAl GhorbanpoorAlexander M. LeshchinskyV. M. MalhotraClaus G. PetersenGeorge V. Teodoro1A

20、CI Committee Reports, Guides, and Commentaries are intended for guidance in planning, designing, executing, and inspecting construction. This document is intended for the use of individuals who are competent to evaluate the significance and limitations of its content and recommendations and who will

21、 accept responsibility for the application of the material it contains. The American Concrete Institute disclaims any and all responsibility for the stated principles. The Institute shall not be liable for any loss or damage arising therefrom.Reference to this document shall not be made in contract

22、documents. If items found in this document are desired by the Architect/Engineer to be a part of the contract documents, they shall be restated in mandatory language for incorporation by the Architect/Engineer.ACI 228.2R-13 supersedes ACI 228.2R-98(04) and was adopted and published June 2013.Copyrig

23、ht 2013, American Concrete Institute.All rights reserved including rights of reproduction and use in any form or by any means, including the making of copies by any photo process, or by electronic or mechanical device, printed, written, or oral, or recording for sound or visual reproduc-tion or for

24、use in any knowledge or retrieval system or device, unless permission in writing is obtained from the copyright proprietors.Allen. G. Davis (deceased) made many contributions to this report.4.3Numerical and experimental simulations, p. 664.4Correlation with intrusive testing, p. 714.5Reporting resul

25、ts, p. 71CHAPteR 5ReFeRenCes, p. 71APPenDIX A: tHeoRetICAL AsPeCts oF MoBILItY PLot oF PILe, p. 81CHAPteR 1IntRoDUCtIon1.1scopeNondestructive testing (NDT) methods are used to deter-mine concrete properties and to evaluate the condition of concrete in deep foundations, bridges, buildings, pavements,

26、 dams, and other concrete construction. For this report, NDT is defined as generally noninvasive, with the excep-tion of transport property tests, which may cause easily-repaired surface damage. While coring and load testing may be considered nondestructive, they are excluded from this report. Refer

27、 to ACI 437R for more information about strength evaluation of existing concrete buildings.NDT methods are applied to concrete construction for four primary reasons:1. Quality control of new construction2. Troubleshooting problems with new and old construction3. Condition evaluation of older concret

28、e for rehabilitation purposes4. Quality assurance of concrete repairsNDT technologies are evolving and research continues to enhance existing methods and develop new methods. The report is intended to provide an overview of the principles of various NDT methods practiced and to summarize their appli

29、cations and limitations. Emphasis is placed on methods that have been applied to measure physical properties other than the strength of concrete in structures, to detect flaws or discontinuities, and to provide data for condition evalua-tion. Methods to estimate in-place compressive strength are pre

30、sented in ACI 228.1R.1.2needs and applicationsNondestructive testing (NDT) methods are increasingly applied for the investigation of concrete structures. This increase in the application of NDT methods is due to a number of factors:a) Technological improvements in hardware and software for data coll

31、ection and analysisb) The economic advantages in assessing large volumes of concrete compared with other methodsc) Ability to perform rapid, comprehensive assessments of existing constructiond) Specification of NDT methods for quality assurance of deep foundations and concrete repairsAn increased us

32、e of NDT methods is occurring despite the lack of testing standards for many of the methods. The development of testing standards is critical for proper appli-cation and expanded use of NDT methods for evaluation of concrete construction.Traditionally, quality assurance of concrete construc-tion has

33、 been performed largely by visual inspection of the construction process and by sampling the concrete to perform standard tests on fresh and hardened specimens. This approach does not provide data on the in-place prop-erties of concrete. NDT methods offer the advantage of providing information on th

34、e in-place properties of hardened concrete, such as the elastic constants, density, resistivity, moisture content, and fluid transport characteristics.Condition assessment of concrete for structural evaluation purposes has been performed mostly by visual examination, coring, and surface sounding, wh

35、ich refers to striking the object surface and listening to characteristics of the resulting sound. Condition assessments are used to examine internal concrete conditions and to obtain specimens for testing. This approach limits the areas of concrete that can be investigated effectively. Some coring

36、may be necessary for calibration purposes, particularly if the concrete strength is required. Cores also cause local damage and limit the information to the core location. Condition assessments can be made with NDT methods to provide essential information for the struc-tural performance of the concr

37、ete, such as:a) Member dimensionsb) Location of cracking, delamination, and debondingc) Degree of consolidation, presence of voids, and honeycombd) Steel reinforcement location and sizee) Corrosion activity of reinforcementf) Extent of damage from freezing and thawing, fire, or chemical exposureg) S

38、trength of concrete1.3objectiveThis report reviews the state of the practice for nonde-structively determining nonstrength physical properties and conditions of hardened concrete. The overall objective is to provide the potential user with a guide to assist in planning, conducting, and interpreting

39、the results of nondestructive tests (NDT) of concrete construction.Chapter 3 discusses the principles, equipment, testing procedures, and data analysis of the various NDT methods. Typical applications and inherent limitations of the methods are discussed to assist the potential user in selecting the

40、 most appropriate method for a particular situation. Chapter 4 discusses the planning and performance of NDT investiga-tions. Included in Chapter 4 are references to in-place tests covered in ACI 228.1R and other applicable methods for evaluating the characteristics of existing concrete.CHAPteR 2not

41、AtIon AnD DeFInItIons2.1notationBecause NDT crosses different science and engineering disciplines, the same symbols are used differently by different practitioners. The context of the symbol should be established and related to the body of text.A = cross-sectional area (3.5.3, 3.6.2); wetted area (3

42、.6.2)American Concrete Institute Copyrighted Materialwww.concrete.org2 RePoRt on nonDestRUCtIVe test MetHoDs FoR eVALUAtIon oF ConCRete In stRUCtURes (ACI 228.2R-13)Ac= shaft cross-sectional area (3.3.3, Appendix A)B = magnetic induction (3.5.5)B = constant in volts (3.5.4)C = concentration (3.6.2);

43、 capacitance (3.5.4); electro-magnetic wave speed (3.8)Cb= bar wave speed (3.2, 3.3.1, 3.3.3); stress wave speed along the pile (Appendix A)Co= speed of light in air (3.8)Cp= P-wave speed (3.2, 3.2.3)CR(f)= surface wave speed of component with frequency f (3.2.4)Cr= ratio of the R-wave speed to the

44、S-wave speed (3.2)Cs= S-wave speed (3.2, 3.2.2)D = depth (3.2.3, 3.8); diffusion coefficient (3.5.3, 3.6.2); diameter (3.2.3)Dp= diffusion coefficient of the ions through the pore fluid (3.5.3)d = depth (3.2.1); diameter (3.3.1)E = Youngs modulus of elasticity (3.2); voltage (3.5.4); maximum accepta

45、ble error (4.2)e = emissivity of the surface (3.7)F = mass flux (3.6.2)f = frequency (3.2.3)G = shear modulus of elasticity (3.2)H = magnetic field strength (3.5.5)I = characteristic shaft impedance (3.3.3); amplitude of alternating current between outer electrodes (3.5.3); hydraulic gradient (3.6.2

46、)Ip= applied polarization current (3.5.4)i = current (3.5.4)icorr= corrosion current density (3.5.4)k = statistical factor (4.2); coefficient of permeability (3.6.2)kd= dynamic stiffness from mobility plot (3.2.5, 3.3.2; Appendix A)L = length (3.3.1, 3.3.3, 3.5.3, Appendix A)Mp= mass of pile (Append

47、ix A)m = mass (3.6.2)N = average mobility (Appendix A)n = sample size (4.2)P = soil damping measure (Appendix A)po= advance estimate of fraction defective (4.2)Q = soil damping measure (Appendix A)Q = flow rate (3.6.2); maximum amplitude in mobility plot of pileR = rate of energy radiation per unit

48、area of surface (3.7); reflection coefficient (3.2); electrical resis-tance in ohm (3.5.3, 3.5.4)Rp= polarization resistance (3.5.4)r = radius (Appendix A)s = spacing between electrodes (3.5.3); sorptivity (3.6.2)T = depth of reflecting interface (3.2.2); absolute temperature of surface (3.7)t = tra

49、vel time from transmitter to receiver (3.2.2); time (3.6.2, 3.8)tc= contact time (3.2.3)V = volume of fluid absorbed (3.6.2); voltage (3.5.3)Vd= wave speed in damaged concrete (3.2.1)Vs= wave speed in sound concrete (3.2.1)X = separation between transmitter and receiver (3.2.1, 3.2.2, 3.2.4)Xo= distance at which the travel times for two wave paths are equal (3.2.1)x = distance (3.6.2)Z = specific acoustic impedance (3.2); depth (3.8)a = signal attenuation (3.8)bs= the lateral soil shear wave velocity (Appendix A)e = dielectric constant (3.8)e0= dielectric cons