ANSI 124 1 2-2005 American National Standard for Plastic Bathtub and Shower Units《塑料浴盆和淋浴装置用美国国家标准》.pdf

《ANSI 124 1 2-2005 American National Standard for Plastic Bathtub and Shower Units《塑料浴盆和淋浴装置用美国国家标准》.pdf》由会员分享，可在线阅读，更多相关《ANSI 124 1 2-2005 American National Standard for Plastic Bathtub and Shower Units《塑料浴盆和淋浴装置用美国国家标准》.pdf（34页珍藏版）》请在麦多课文档分享上搜索。

1、ANSI Z124.1.2 - 2005 Revision and Harmonization of ANSI Z124.1 - 1995 and ANSI Z124.2 - 1995 American National Standard for Plastic Bathtub and Shower Units Secretariat International Association of Plumbing and Mechanical Officials Approved July 18, 2005 American National Standards Institute, Inc. L

2、icensed to Sarah Zhou. ANSI order X_63851. Downloaded 5/30/2008 4:19 AM. Single user license only. Copying and networking prohibited.Approval of an American National Standard requires verification by ANSI that the requirements for due process, consensus, and other criteria for approval have been met

3、 by the standards developer. Consensus is established when, in the judgement of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materially affected inter- ests. Substantial agreement means much more than a simple majority, but not necessari- ly unanimity. C

4、onsensus requires that all views and objections be considered, and that a concerted effort be made toward their resolution. The use of American National Standards is completely voluntary; their existence does not in any respect preclude anyone, whether he has approved the standards or not, from manu

5、facturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. The American National Standards Institute does not develop standards and will in no cir- cumstances give an interpretation of any American National Standard. Moreover, no person shall have

6、the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. Requests for inter- pretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard. CAUTION NOTICE: This Am

7、erican National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all sta

8、ndards by calling or writing the American National Standards Institute. Published by International Association of Plumbing and Mechanical Officials 5001 East Philadelphia Street, Ontario, CA 91761 Copyright 2005 by International Association of Plumbing and Mechanical Officials All rights reserved. N

9、o part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. Printed in the United States of America American National Standard Licensed to Sarah Zhou. ANSI order X_63851. Downloaded 5/30/2008 4:19 AM. Si

10、ngle user license only. Copying and networking prohibited.Contents Page Foreword .iii 1 Scope and Purpose 1 1.1 Scope .1 1.2 Purpose 1 1.3 Normative References .1 2 General Requirements.1 2.1 Materials1 2.2 Dimensional Tolerances 2 2.3 Units for Testing2 2.4 Installation Instructions .2 2.5 Care and

11、 Maintenance Instructions .2 2.6 Identification2 2.7 Grab Bars.2 2.8 Raised Flanges and Tiling Beads 2 2.9 Commonly Used Nomenclature 2 3 Workmanship and Finish 2 3.1 Unit Preparation.2 3.2 Method of Inspection of the Unit Surface .2 3.3 Surface Test.2 3.4 Subsurface Test .3 4 Structural Integrity o

12、f Complete Units4 4.1 Unit Preparation.4 4.2 Drain Fitting Connection.4 4.3 Point Impact Loads4 4.4 Load on Seats 4 4.5 Loads on Rim and Bottom of Bathubs and on Theshold . and Bottom of Showers 4 4.6 Area Impact Load on Wall Surrounds.5 4.7 Loads on Wall Surrounds 6 4.8 Radii Load Test .6 4.9 Loads

13、 on Unsupported Bathtub Areas.6 5. Physical Characteristics of Materials6 5.1 Colorfastness .6 5.2 Stain Resistance Test.6 5.3 Wear and Cleanability .7 5.4 Cigarette Test.9 5.5 Chemical Resistance Test9 5.6 Ignition Test.9 6. Additional Material Tests10 6.1 Water Resistance Test .10 6.2 Laboratory T

14、est for Non-Integral Flange-Fixture Seal .10 6.3 Resistance to Fungi and Bacteria Growth (Type 6 Units).11 6.4 Puncture Resistance Test (Type 6 Units) 11 7 Provisions for Government Procurement11 Tables 1 Appearance Requirements 3 2 Reagents Used in Stain Resistance Test .7 i Licensed to Sarah Zhou.

15、 ANSI order X_63851. Downloaded 5/30/2008 4:19 AM. Single user license only. Copying and networking prohibited.Page Figures 1 Load Test for Drain Fitting Connections 12 2 Fixture for Measuring Tub Bottom Deflection/Load Test on Threshold and Bottom.13 3 Typical Test Stand 14 4 Load Test on Bathub Ri

16、m and Bottom, and Load on Unsupported Areas .14 5 Brush Holder (Sled) (Z124 Wear Test).15 6 Platform or as a multi-piece unit distributed as part of the bathtub or shower unit. Such products shall meet the requirements as outlined in this standard. While this standard covers the performance require-

17、 ments of plastic bathtub or shower units and describes these performance requirements in terms of methods of test applicable to all such units, a number of different materials and methods of manufacture shall be permitted to be used to meet these requirements. Each of these materials and meth- ods

18、have different properties which will affect its end per- formance and suitability for the intended use. For this rea- son, portions of the standard are broken into separate requirements designed to identify these individual charac- teristics. The materials and equipment which are listed as having be

19、en used to conduct the testing procedures in this standard are provided solely for informational reference. Materials and equipment of similar design, composition and specifica- tion shall only be used to conduct these testing procedures when they produce equivalent results. 1.2 Purpose. The purpose

20、 of this standard is to establish minimum performance requirements for plastic bathtub or shower units. Conformance to this standard and test procedures here- in shall indicate the acceptability of a plastic bathtub or shower unit as a plumbing fixture. 1.3 Normative references The following standar

21、ds contain provisions which, through reference in this text, constitute provisions of this American National Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this American National Standard are encourag

22、ed to investigate the possibility of applying most recent editions of the standards indicated below. ASTM D 883-00, Terminology Relating to Plastics ASTM D 2244-02 e1 , Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates ASTM D 2565-99, P

23、ractice for Operating Xenon Arc Exposure of Plastics Intended for Outdoor Applications ASTM E 84-05 (NFPA 255-00), Test Method for Surface Burning Characteristics of Building Materials ASTM E 162-98, Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source ASTM E 662-03 e

24、1 , Test Method for Specific Optical Density of Smoke Generated by Solid Materials ASTM F 446-85(2004 e1 ), Consumer Safety Specification for Grab Bars and Accessories Installed in the Bathing Area ASTM G21-96(2002), Practice For Determining Resistance Of Synthetic Polymeric Materials To Fungi NFPA

25、255-00, (See ASTM E 84) NFPA 258-01, Recommended Practice for Determining Smoke Generation of Solid Materials 2. General requirements 2.1 Materials 2.1.1 Composition. The units shall be made of suit- able grades of plastic resins and such other filling, coloring, reinforcing, and coating materials a

26、s will meet the perfor- mance requirements of this standard. 2.1.2 Finish. The finished surface of the unit shall be of a quality which meets all of the applicable requirements of the standard. Six common types of plastic finishes shall be as defined. (1) Type 1 - No separate surface finish: The sur

27、face finish is the same as, and is usually integral with, the struc- tural base. (Excluding Type 4.) (2) Type 2 - Coated surface finish: These units are characterized by the presence of a surface coating which is applied to the structural base either prior to or after the molding process. (Excluding Type 4.) 1 IAPMO/ANSI Z124.1.2-2005 Licensed to Sarah Zhou. ANSI order X_63851. Downloaded 5/30/2008 4:19 AM. Single user license only. Copying and networking prohibited.