IEC 63004-2015 Standard for receiver fixture interface《接收器固定设备接口标准》.pdf

《IEC 63004-2015 Standard for receiver fixture interface《接收器固定设备接口标准》.pdf》由会员分享，可在线阅读，更多相关《IEC 63004-2015 Standard for receiver fixture interface《接收器固定设备接口标准》.pdf（162页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 63004 Edition 1.0 2015-12 INTERNATIONAL STANDARD Standard for receiver fixture interface IEC 63004:2015-12(en) IEEE Std 1505-2010 IEEE Std 1505 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEEE All rights reserved. IEEE is a registered trademark in the U.S. Patent any IE

2、C National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEEE Standards documents are developed within IEEE Societies and Standards C

3、oordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board. IEEE develops its standards through a consensus development process, which brings together volunteers representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily members

4、of IEEE and serve without compensation. While IEEE administers the process and establishes rules to promote fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the accuracy of any of the information contained in its standards. Use of IEEE Standards do

5、cuments is wholly voluntary. IEEE documents are made available for use subject to important notices and legal disclaimers (see http:/standards.ieee.org/IPR/disclaimers.html for more information). IEC collaborates closely with IEEE in accordance with conditions determined by agreement between the two

6、 organizations. 2) The formal decisions of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. The formal decisions of IEEE on technical

7、matters, once consensus within IEEE Societies and Standards Coordinating Committees has been reached, is determined by a balanced ballot of materially interested parties who indicate interest in reviewing the proposed standard. Final approval of the IEEE standards document is given by the IEEE Stand

8、ards Association (IEEE-SA) Standards Board. 3) IEC/IEEE Publications have the form of recommendations for international use and are accepted by IEC National Committees/IEEE Societies in that sense. While all reasonable efforts are made to ensure that the technical content of IEC/IEEE Publications is

9、 accurate, IEC or IEEE cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications (including IEC/IEEE Publications) transparently to the maxim

10、um extent possible in their national and regional publications. Any divergence between any IEC/IEEE Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC and IEEE do not provide any attestation of conformity. Independent certification bod

11、ies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC and IEEE are not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall

12、 attach to IEC or IEEE or their directors, employees, servants or agents including individual experts and members of technical committees and IEC National Committees, or volunteers of IEEE Societies and the Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board

13、, for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC/IEEE Publication or any other IEC or IEEE Publications. 8) Attention is

14、 drawn to the normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that implementation of this IEC/IEEE Publication may require use of material covered by patent r

15、ights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights in connection therewith. IEC or IEEE shall not be held responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into th

16、e legal validity or scope of Patent Claims or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determin

17、ation of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. IEC 63004:2015 IEEE Std 1505-2010Published by IEC under license from IEEE. 2010 IEEE. All rights reserved. International Standard IEC 63004/IEEE Std 1505-2010 has been proce

18、ssed through IEC technical committee 91: Electronics assembly technology, under the IEC/IEEE Dual Logo Agreement. The text of this standard is based on the following documents: IEEE Std FDIS Report on voting IEEE Std 1505-2010 91/1275/FDIS 91/1299/RVD Full information on the voting for the approval

19、of this standard can be found in the report on voting indicated in the above table. The IEC Technical Committee and IEEE Technical Committee have decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ i

20、n the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IEC 63004:2015 IEEE Std 1505-2010IEEE Std 1505-2010 (Revision of IEEE Std 1505-2006) IEEE Standard for Receiver Fixture Interface Sponsor IEEE Stan

21、dards Coordinating Committee 20 on Test and Diagnosis for Electronic Systems Approved 30 September 2010 IEEE-SA Standards Board Approved 15 July 2011 American National Standards Institute IEC 63004:2015 IEEE Std 1505-2010 Abstract: A mechanical and electrical specification for implementing a common

22、interoperable mechanical quick-disconnect interconnect system for use by industry for interfacing large numbers of electrical signals (digital, analog, RF, power, etc.) is provided. These large interface panels (receiver and fixture panels) are employed primarily in test systems between stimulus/mea

23、surement assets and a related unit-under-test (UUT), although any application involving high-density contacts requiring a quick disconnect interface could benefit. The receiver is a receptacle that is mounted to test system mates with multiple fixtures, which serve as the buffer between the UUT and

24、automatic test equipment (ATE). Fixtures translate standard input/output (I/O) signal routing offered at the receiver to a wiring interface that directly connects to the UUT. These UUT interfaces can represent cable connectors, direct plug-in (printed circuit board edge connectors), sensor monitorin

25、g, or manual feedback from the test technician. The primary objectives of this standard are: (a) to establish interface standards that permit interchangeability of mechanical/electrical receiver/fixture/connector product assemblies from various manufacturers under an open architecture; and (b) to de

26、velop within this framework a defined set(s) of interconnecting connector and mechanical specifications that supports available, accepted, low-cost commercial technology to reduced dependence on proprietary designs and extend life-cycle availability. Keywords: connector, fixture, framework, interface, interoperability, mass-interconnect, quick disconnect, receiver, specification IEC 63004:2015 IEEE Std 1505-2010