IEC 62127-2 Edition 1.1-2013 Ultrasonics - Hydrophones - Part 2 Calibration for ultrasonic fields up to 40 MHz《超音波学.水听器.第2部分 超音波场小于40 MHz的校准》.pdf

《IEC 62127-2 Edition 1.1-2013 Ultrasonics - Hydrophones - Part 2 Calibration for ultrasonic fields up to 40 MHz《超音波学.水听器.第2部分 超音波场小于40 MHz的校准》.pdf》由会员分享，可在线阅读，更多相关《IEC 62127-2 Edition 1.1-2013 Ultrasonics - Hydrophones - Part 2 Calibration for ultrasonic fields up to 40 MHz《超音波学.水听器.第2部分 超音波场小于40 MHz的校准》.pdf（214页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62127-2 Edition 1.1 2013-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Ultrasonics Hydrophones Part 2: Calibration for ultrasonic fields up to 40 MHz Ultrasons Hydrophones Partie 2: Etalonnage des champs ultrasoniques jusqu 40 MHz IEC62127-2:2007+A1:2013 colourinsideTHIS PUBLICATION IS COPYRIG

2、HT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC o

3、r IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de re

4、production rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays

5、 du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Vare

6、mb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC pub

7、lications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to fin

8、d IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publi

9、cations released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also

10、 known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotec

11、hnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuil

12、lez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit

13、 dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une

14、 fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Voc

15、abulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62127-2 Edition 1.1 2013-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Ultraso

16、nics Hydrophones Part 2: Calibration for ultrasonic fields up to 40 MHz Ultrasons Hydrophones Partie 2: Etalonnage des champs ultrasoniques jusqu 40 MHz INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 11.040.50 ISBN 978-2-8322-0649-2 Registered trademark of t

17、he International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colourinsi

18、de 2 62127-2 IEC:2007+A1:2013 CONTENTS CONTENTS 2 FOREWORD . 5 INTRODUCTION . 7 1 Scope . 8 2 Normative references 8 3 Terms, definitions and symbols . 9 4 List of symbols 15 5 Overview of calibration procedures . 17 5.1 Principles 17 5.2 Summary of calibration procedures 18 5.3 Reporting of results

19、 . 19 5.4 Recommended calibration periods . 21 6 Generic requirements of a hydrophone calibration system . 21 6.1 Mechanical positioning . 21 6.1.1 General . 21 6.1.2 Accuracy of the axial hydrophone position 21 6.1.3 Accuracy of the lateral hydrophone position 21 6.2 Temperature measurements and te

20、mperature stability . 22 6.3 Hydrophone size 22 6.4 Measurement vessel and water properties . 22 6.5 Measurement of output voltage 23 7 Electrical considerations . 23 7.1 Signal type 23 7.2 Earthing . 23 7.3 Measurement of hydrophone output voltage . 24 7.3.1 General . 24 7.3.2 Electrical loading by

21、 measuring instrument . 24 7.3.3 Electrical loading by extension cables 24 7.3.4 Noise . 24 7.3.5 Cross-talk (radio-frequency rf pick-up) and acoustic interference . 25 7.3.6 Integral hydrophone pre-amplifiers . 25 8 Preparation of hydrophones 25 8.1 General . 25 8.2 Wetting 25 8.3 Hydrophone suppor

22、t 25 8.4 Influence of cable 26 9 Free field reciprocity calibration 26 9.1 General . 26 9.2 Object . 26 9.3 General principles 26 9.3.1 General . 26 9.3.2 Three-transducer reciprocity calibration method . 26 9.3.3 Self-reciprocity calibration method . 26 9.3.4 Two-transducer reciprocity calibration

23、method 27 62127-2 IEC:2007+A1:2013 3 9.4 Two-transducer reciprocity calibration method 27 9.4.1 Apparatus 27 9.4.2 Procedure 27 10 Free field calibration by planar scanning . 27 10.1 General . 27 10.2 Object . 27 10.3 General principle . 28 10.4 Procedural requirements 29 10.4.1 Hydrophone scanning

24、29 10.5 Procedure 29 10.5.1 Power measurement 29 10.5.2 Transducer mounting . 30 10.5.3 Measurement conditions 30 10.5.4 Measurements . 30 10.6 Corrections and sources of uncertainty 30 11 Free field calibration by optical interferometry . 30 11.1 General . 30 11.2 Principle 31 12 Calibration by com

25、parison using a standard hydrophone . 31 12.1 General . 31 12.2 Object . 31 12.3 Principle 31 12.4 Procedural requirements 32 12.4.1 Source transducer . 32 12.4.2 Source transducer drive signal . 32 12.4.3 Measurement system . 32 12.5 Procedure 32 12.5.1 Measurements (Type I): determination of the d

26、irectional response of a hydrophone 32 12.5.2 Measurements (Type II): calibration by comparison using a standard hydrophone 33 12.6 Maximum hydrophone size . 33 Annex A (informative) Assessment of uncertainty in free field calibration of hydrophones . 35 Annex B (informative) Behaviour of PVDF polym

27、er sensors in high intensity ultrasonic fields . 37 Annex C (informative) Electrical loading corrections . 40 Annex D (informative) Absolute calibration of hydrophones using the planar scanning technique 41 Annex E (informative) Properties of water . 49 Annex F (informative) The absolute calibration

28、 of hydrophones by optical interferometry up to 40 MHz 51 Annex G (informative) Waveform concepts 61 Annex H (informative) Time delay spectrometry requirements and a brief review of the technique 71 Annex I (informative) Determination of the phase response of hydrophones 74 Annex J (informative) Max

29、imum size considerations for the active element of a hydrophone 80 4 62127-2 IEC:2007+A1:2013 Annex K (informative) Two-transducer reciprocity calibration method 82 Bibliography 97 Figure F.1 Experimental set-up of the interferometric foil technique 54 Figure F.2 End-of-cable open-circuit sensitivit

30、y, Mc, of a coplanar membrane hydrophone . 56 Figure F.3 Hydrophone waveform generated by a 9 m coplanar membrane hydrophone positioned at the focus of a 5 MHz transducer (focal length 51 mm) 57 Figure F.4 Interferometer (displacement) waveform generated with the pellicle positioned at the focus of

31、the 5 MHz transducer (focal position 51 mm) . 58 Figure F.5 Frequency spectrum of the displacement waveform (lower curve) and the differentiated displacement waveform (upper curve) 58 Figure F.6 Sensitivity of a 0,2 mm active element diameter of a 9 m bilaminar membrane hydrophone determined at 5 MH

32、z intervals over the frequency range 5 MHz to 60 MHz . 59 Figure G.1 Coordinates of a field point, P, in the near field of a plane-circular source transducer of radius, ta 68 Figure I.1 Phase of end-of-cable open-circuit sensitivity for two membrane hydrophones . 76 Figure I.2 Phase of end-of-cable

33、open-circuit sensitivity for a 0,2 mm needle hydrophone . 78 Figure K.1 Experimental arrangement for the two-transducer reciprocity calibration method . 95 Figure K.2 Block diagram of the electrical circuit for the two-transducer reciprocity calibration method. 95 Figure K.3 The value of the term Gc

34、(part of the correction factor k) plotted as a function of the normalized distance. 96 Figure K.4 Average pressure plotted against normalized distance for transducers of different size. Parameter is the ratio receiver/transmitter diameter (according to reference 7 in Clause K.12) . 96 Table 1 List o

35、f typical uncertainty values obtained by the calibration methods specified in this standard and for the frequency range listed here . 19 Table E.1 Speed of sound c 36, 37 and specific acoustic impedance, c, as a function of temperature, for propagation in water 49 Table G.1 Temporal waveform and hyd

36、rophone position concepts described in this annex . 61 Table I.1 Example of uncertainties (where a coverage factor, k = 2, is used) for a HTDS phase calibration of a needle hydrophone with a diameter of 0,2 mm, expressed at a confidence level of 95 % 76 62127-2 IEC:2007+A1:2013 5 INTERNATIONAL ELECT

37、ROTECHNICAL COMMISSION _ ULTRASONICS HYDROPHONES Part 2: Calibration for ultrasonic fields up to 40 MHz FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The o

38、bject of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifica

39、tions (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations lia

40、ising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters expre

41、ss, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committ

42、ees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National

43、 Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not

44、 provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have th

45、e latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever

46、, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications

47、 is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. This consolidated versio

48、n of IEC 62127-2 consists of the first edition (2007) documents 87/353/CDV and 87/372/RVC, its amendment 1 (2013) documents 87/519/FDIS and 87/527/RVD and its corrigendum of August 2008. It bears the edition number 1.1. The technical content is therefore identical to the base edition and its amendme

49、nt and has been prepared for user convenience. A vertical line in the margin shows where the base publication has been modified by amendment 1. Additions and deletions are displayed in red, with deletions being struck through. 6 62127-2 IEC:2007+A1:2013 International Standard IEC 62127-2 has been prepared by IEC technical committee 87: Ultrasonics. IEC 62127-1, IEC 62127-2 and IEC 62127-3 are being publis