IEC 61969-2-2011 Mechanical structures for electronic equipment - Outdoor enclosures - Part 2 Coordination dimensions《电子设备的机械结构.户外机壳.第2部分 配合尺寸》.pdf

《IEC 61969-2-2011 Mechanical structures for electronic equipment - Outdoor enclosures - Part 2 Coordination dimensions《电子设备的机械结构.户外机壳.第2部分 配合尺寸》.pdf》由会员分享，可在线阅读，更多相关《IEC 61969-2-2011 Mechanical structures for electronic equipment - Outdoor enclosures - Part 2 Coordination dimensions《电子设备的机械结构.户外机壳.第2部分 配合尺寸》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61969-2 Edition 2.0 2011-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Mechanical structures for electronic equipment Outdoor enclosures Part 2: Coordination dimensions Structures mcaniques pour quipement lectronique Enveloppes de plein air Partie 2: Dimensions de coordination IEC61969-2:2011

2、THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission i

3、n writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for furthe

4、r information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit

5、 national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de

6、Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publica

7、tions The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by

8、a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications

9、released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the Internat

10、ional Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03

11、00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publ

12、ications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en u

13、tilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois p

14、ar mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivale

15、nts dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clie

16、nts ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61969-2 Edition 2.0 2011-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Mechanical structures for electronic equipment Outdoor enclosures Part 2: Coordination dimensions Structures mcaniques pour quipement lectro

17、nique Enveloppes de plein air Partie 2: Dimensions de coordination INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE H ICS 31.240 PRICE CODE CODE PRIX ISBN 978-2-88912-762-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Co

18、mmission Electrotechnique Internationale 2 61969-2 IEC:2011 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 Arrangement overview 5 4 Coordination dimensions 6 4.1 General . 6 4.2 Height . 7 4.3 Width 8 4.4 Depth 8 Figure 1 Arrangement overview . 6 Figure 2 Outdoor enclosure coordinati

19、on dimensions . 7 Table 1 HEand HE1dimensions . 7 Table 2 WEand WE1dimensions . 8 Table 3 DEand DE1dimensions . 8 61969-2 IEC:2011 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT OUTDOOR ENCLOSURES Part 2: Coordination dimensions FOREWORD 1) The Internati

20、onal Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electroni

21、c fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; a

22、ny IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standar

23、dization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has repr

24、esentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IE

25、C cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publi

26、cations. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some area

27、s, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents includi

28、ng individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or relianc

29、e upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elem

30、ents of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61969-2 has been prepared by subcommittee 48D: Mechanical structures for electronic equipment, of IEC technical committee 48:

31、Electromechanical components and mechanical structures for electronic equipment. This second edition cancels and replaces the first edition issued in 2000. It constitutes a technical revision. The main technical changes with regard to the previous edition are as follows: It was the intention when IE

32、C 61969-2 Ed. 1.0 was created that a sectional standard is to be followed by a detail standard, consisting of IEC 61969-2-1 and IEC 61969-2-2. The intention of detail standards was to create a recommended but cost-effective range of outdoor enclosure solutions offered from multiple vendors. However,

33、 it became evident that 4 61969-2 IEC:2011 the outdoor enclosure applications were extremely application specific and the intended effect became irrelevant. Consequently, IEC 61969-2-1 and IEC 61969-2-2 became obsolete and will be withdrawn at the time when IEC 61969-2 Ed.2.0 is published. To provid

34、e for a useful outdoor enclosure installation matrix IEC 61969-2 Ed. 2.0 focuses on overall outdoor enclosure co-ordination dimension only. The text of this standard is based on the following documents: FDIS Report on voting 48D/482/FDIS 48D/496/RVD Full information on the voting for the approval of

35、 this standard can be found in the report on voting indicated in the above table. A list of all parts of IEC 61969 series, under the general title Mechanical structures for electronic equipment Outdoor enclosures, can be found on the IEC website. This publication has been drafted in accordance with

36、the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirme

37、d, withdrawn, replaced by a revised edition, or amended. 61969-2 IEC:2011 5 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT OUTDOOR ENCLOSURES Part 2: Coordination dimensions 1 Scope This part of IEC 61969 applies to the design of enclosures for outdoor applications for stationary use at non-weatherp

38、rotected locations as defined in IEC 61969-1 Ed.2.0. The internal and external coordination dimensions are derived from IEC 60917-2. The internal dimensions meet the mounting dimensions of subracks in accordance with IEC 60917-2-2 and IEC 60297-3. The external dimensions, compared to IEC 60917-2, ar

39、e partly increased in order to meet the design requirements of the outdoor specific conditions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest e

40、dition of the referenced document (including any amendments) applies. IEC 60917-2, Modular order for the development of mechanical structures for electronic equipment practices Part 2: Sectional specification Interface co-ordination dimensions for the 25 mm equipment practice3 Arrangement overview A

41、n example of an outdoor enclosure is given in Figure 1. Application specific roofs and/or bases/plinth, cable entry/exit and external mounted cable entry or cable management boxes are not covered by this standard. 6 61969-2 IEC:2011 Base/plinth (see NOTE) Outdoor enclosure as defined in this specifi

42、cation Subrack with plug-in units or chassis Roof (see NOTE) Management box (see NOTE) Miscellaneous devices, e.g. batteries Management box (see NOTE) IEC 2455/11 NOTE The enclosure may be closed by doors and at the top and/or bottom without the use of any additional roof or a base/plinth. Managemen

43、t boxes may be attached at any surface of the enclosure (inclusive doors) and are typically used for cable and/or power management etc and are application specific. Specific roofs and/or bases may be optional for technical or appearance reasons and are not specified in this standard. Figure 1 Arrang

44、ement overview 4 Coordination dimensions 4.1 General Following the coordination rules as defined in IEC 60917-2, the external dimensions may be decreased and the aperture dimensions may be decreased. Smaller parts such as locks, hinges or handles may exceed the enclosure dimension by 25 mm. However,

45、 special requirements, regulatory or application specific are exempted. The figures do not imply product design. Only the coordination dimensions are relevant. Smaller parts, for example locks or handles, may exceed the enclosure dimensions by 25 mm maximum. See Figure 2 and Tables 1 to 3. 61969-2 I

46、EC:2011 7 Front view Front line including doors Top view (A-A) WE1WEHE1HEDE1DEA A IEC 2456/11 Key HEoverall height HE1aperture height WEoverall width WE1aperture width DEoverall depth DE1aperture depth Figure 2 Outdoor enclosure coordination dimensions 4.2 Height Table 1 HEand HE1dimensions Dimensio

47、ns in millimetres HE b400 500 600 700 800 900 1 000 1 100 1 200 1 300 1 400 HE1 a150 250 350 450 550 650 750 850 950 1 050 1 150 HE b1 500 1 600 1 700 1 800 1 900 2 000 2 100 2 200 2 300 2 400 2 500 2 600 HE1 a1 250 1 350 1 450 1 550 1 650 1 750 1 850 1 950 2 050 2 150 2 250 2 350 aAperture height d

48、imensions: HE1may be increased or decreased. Multiples of 5 mm are to be used. bFormulae for any optional outside height dimension: HE= HE1+ 200 + (n 50). 8 61969-2 IEC:2011 4.3 Width Table 2 WEand WE1dimensions Dimensions in millimetres WE b300 400 500 600 700 800 900 1 000 1 100 1 200 WE1 a200 300

49、 400 500 500 600 700 800 900 1 000 WE b1 300 1 400 1 500 1 600 1 700 1 800 1 900 2 000 2 100 2 200 2 300 WE1 a1 100 1 200 1 300 1 400 1 500 1 600 1 700 1 800 1 900 2 000 2 100 aAperture width dimensions WE1may be increased or decreased. Multiples of 5 mm are to be used. bFormulae for any optional outside width dimension from 700 mm upwards: WE= WE1+ 150 + (n 50). For width of 600 mm an