IEC 61121-2012 Tumble dryers for household use - Methods for measuring the performance《家用滚筒式干衣机.性能测试方法》.pdf

《IEC 61121-2012 Tumble dryers for household use - Methods for measuring the performance《家用滚筒式干衣机.性能测试方法》.pdf》由会员分享，可在线阅读，更多相关《IEC 61121-2012 Tumble dryers for household use - Methods for measuring the performance《家用滚筒式干衣机.性能测试方法》.pdf（112页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61121 Edition 4.0 2012-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Tumble dryers for household use Methods for measuring the performance Sche-linge tambour usage domestique Mthodes de mesure de laptitude la fonction IEC 61121:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, G

2、eneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee i

3、n the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication

4、 contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des qu

5、estions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 G

6、eneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of

7、 IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of

8、 criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-lin

9、e and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electr

10、otechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la

11、 premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez

12、ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des in

13、formations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electrop

14、edia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique Internat

15、ional (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61121 Edition 4.0 2012-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Tumble dryers for household use Methods for

16、 measuring the performance Sche-linge tambour usage domestique Mthodes de mesure de laptitude la fonction INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE X ICS 97.060 PRICE CODE CODE PRIX ISBN 978-2-8322-0936-3 Registered trademark of the International Electrotec

17、hnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61121 IEC:2012 CONTENTS FOREWORD .

18、5 INTRODUCTION . 7 1 Scope . 8 2 Normative references . 8 3 Terms, definitions and symbols 8 3.1 Terms and definitions 8 3.2 List of symbols 12 4 Requirements . 13 4.1 General . 13 4.2 Rated capacity 13 4.3 Dimensions . 14 5 Test conditions, materials, equipment and instrumentation . 14 5.1 General

19、. 14 5.2 Ambient conditions 14 5.2.1 Electricity supply . 14 5.2.2 Water supply . 15 5.2.3 Ambient temperature and humidity 16 5.3 Test materials . 16 5.3.1 General . 16 5.3.2 Test loads . 16 5.3.3 Detergents . 17 5.4 Equipment . 17 5.4.1 Equipment for normalization 17 5.4.2 Equipment for conditioni

20、ng the test load 17 5.4.3 Equipment for wetting the test load prior to a test 17 5.4.4 Other equipment 17 5.5 Instrumentation and accuracy 18 6 Preparation for testing 18 6.1 General . 18 6.2 Installation of the tumble dryer 18 6.3 Preparation of the tumble dryer for a test series 19 6.4 Preparation

21、 of the tumble dryer for a test run 19 6.5 Preparation of test loads . 19 6.5.1 General . 19 6.5.2 Pre-treatment of new test load items prior to use . 20 6.5.3 Requirements regarding the age of test load items 20 6.5.4 Normalization of test load items . 20 6.5.5 Conditioning of test load items . 21

22、6.5.6 Test load composition 22 6.5.7 Wetting 24 7 Performance measurements General requirements . 24 8 Tests for performance 25 8.1 General . 25 8.2 Test procedure for performance tests 25 8.2.1 Test conditions, materials and preparation for testing 25 61121 IEC:2012 3 8.2.2 Programme 25 8.2.3 Test

23、load . 26 8.2.4 Test procedure 26 8.2.5 Validity of a test run . 26 8.2.6 Validity of a test series 27 8.3 Measurements to determine water and energy consumption and programme time . 27 8.3.1 General . 27 8.3.2 Procedure 28 8.4 Measurements to determine condensation efficiency . 28 8.4.1 General . 2

24、8 8.4.2 Procedure 28 8.5 Measurements to determine evenness of drying 28 8.5.1 General . 28 8.5.2 Procedure 28 8.6 Measurements to determine exhaust air volume 29 9 Assessment of performance . 29 9.1 General . 29 9.2 Final moisture content of the load 29 9.3 Corrected electrical energy consumption .

25、 30 9.4 Corrected water consumption 30 9.5 Corrected programme time 31 9.6 Condensation efficiency 32 9.7 Evenness of drying 32 9.8 Exhaust air volume 33 10 Data to be reported 33 Annex A (normative) Reference list 34 Annex B (normative) Nominal and standard exhaust duct for tumble dryer testing 35

26、Annex C (informative) Flow diagrams . 38 Annex D (normative) Test report data to be reported . 40 Annex E (normative) Procedure to determine test load size where rated capacity is not declared . 44 Annex F (normative) Flexible initial moisture content method . 45 Annex G (informative) Assessment of

27、evenness of drying 47 Annex H (informative) Measurement of exhaust air volume 48 Bibliography 50 Figure B.1 Pressure/volumetric air flow curve 35 Figure B.2 Standard exhaust duct (dimensions are in millimetres). 36 Figure B.3 Standard exhaust simulator (dimensions are in millimetres) . 37 Figure C.1

28、 Decision chart illustrating the requirements for a valid test series for automatic tumble dryers 38 Figure C.2 Decision chart illustrating the requirements for a valid test series for non automatic tumble dryers 39 Figure H.1 Suction chamber setup . 49 Table 1 List of symbols 12 4 61121 IEC:2012 Ta

29、ble 2 Specification of instruments 18 Table 3 Number of items in the cotton test load for various test load masses 22 Table 4 Number of items in the synthetic/blends test load for various test load masses . 23 Table 5 Specifications for initial moisture content in the test load . 24 Table 6 Specific

30、ation for final moisture content of the test load after drying 26 Table D.1 Identification data 40 Table D.2 Test measurements . 41 Table D.3 Test conditions and materials 43 Table D.4 Weighted average age Cotton load . 43 61121 IEC:2012 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ TUMBLE DRYERS FO

31、R HOUSEHOLD USE METHODS FOR MEASURING THE PERFORMANCE FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operat

32、ion on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “

33、IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this prepa

34、ration. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international conse

35、nsus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts a

36、re made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications t

37、ransparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independe

38、nt certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liabi

39、lity shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (inclu

40、ding legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of

41、this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61121 has been prepared by subcommittee 59D: H

42、ome laundry appliances, of IEC technical committee 59: Performance of household and similar electrical appliances. This fourth edition cancels and replaces the third edition published in 2002 and Amendment 1 (2005). This edition constitutes a technical revision. This edition includes the following s

43、ignificant technical changes with respect to the previous edition: a) General: more terms have been defined and some previous definitions have been streamlined, in addition to the correction of some symbols and equations; where possible, definitions and terms have been used in common with IEC 60456:

44、2010; the content has been organised into a more logical and simple structure, and repetitive sections have been removed. 6 61121 IEC:2012 b) Conditions of measurement: the wording of various sections has been revised to reduce ambiguity; limits have been defined for water characteristics for automa

45、tic tumble dryers that are sensitive to conductivity as well as methods to adjust these characteristics where necessary. c) Reproducibility and repeatability of test results: revision of the specification for the cotton test load to include suitable test materials which are currently available on th

46、e market; more careful definition of the process and conditions for pre-treatment, conditioning and normalization. d) Test methods: accuracy of measurement has been defined for all instruments; limits and interpretations of the allowable final moisture content for each type of dryer are now defined;

47、 practical advice regarding the test procedure has been given with the aim of reducing ambiguity. Words in bold in the text are defined in Clause 3. This bilingual version (2013-07) corresponds to the monolingual English version, published in 2012-02. The text of this standard is based on the follow

48、ing documents: FDIS Report on voting 59D/393/FDIS 59D/395/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordan

49、ce with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61121 IEC:2012 7 I