IEC 60832-1-2010 Live working - Insulating sticks and attachable devices - Part 1 Insulating sticks《带电作业.绝缘杆及附件设备.第1部分 绝缘杆》.pdf

《IEC 60832-1-2010 Live working - Insulating sticks and attachable devices - Part 1 Insulating sticks《带电作业.绝缘杆及附件设备.第1部分 绝缘杆》.pdf》由会员分享，可在线阅读，更多相关《IEC 60832-1-2010 Live working - Insulating sticks and attachable devices - Part 1 Insulating sticks《带电作业.绝缘杆及附件设备.第1部分 绝缘杆》.pdf（98页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60832-1Edition 1.0 2010-02INTERNATIONAL STANDARD NORME INTERNATIONALELive working Insulating sticks and attachable devices Part 1: Insulating sticks Travaux sous tension Perches isolantes et outils adaptables Partie 1: Perches isolantes IEC60832-1:2010 THIS PUBLICATION IS COPYRIGHT PROTECTED Co

2、pyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member N

3、ational Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rser

4、vs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur.

5、Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email

6、: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publica

7、tions is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, t

8、ext, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by em

9、ail. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online.

10、Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electr

11、otechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. V

12、euillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfren

13、ce, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues.

14、 Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egale

15、ment appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl

16、.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60832-1Edition 1.0 2010-02INTERNATIONAL STANDARD NORME INTERNATIONALELive working Insulating sticks and attachable devices Part 1: Insulating sticks Travaux sous tension Perches isolantes et outils adaptables Partie 1: Perches isolantes INTERNATIONAL ELE

17、CTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XICS 13.260; 29.240.20; 29.260.99 PRICE CODECODE PRIXISBN 2-8318-1077-6 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 60832-1 IEC:2010 CONTENTS

18、FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references .7 3 Terms, definitions and symbols 7 3.1 Terms and definitions 7 3.2 Symbols 8 4 Requirements .8 4.1 General .8 4.2 Electrical insulation .8 4.3 Electrical category of end fittings.9 4.4 Dimensional and mechanical requirements9 4.4.1 Dimens

19、ional requirements .9 4.4.2 Mechanical requirements.9 4.5 Insulating sticks end fittings 11 4.5.1 Mechanical protection11 4.5.2 Protection against corrosion 11 4.5.3 Conductive parts .11 4.6 Multiple-tube or multiple-rod tools .11 4.7 Marking .11 4.8 Instructions for use12 5 Tests 12 5.1 General .12

20、 5.2 Visual inspection .13 5.3 Dimensional check 13 5.4 Durability of marking .13 5.5 Mechanical tests .13 5.5.1 Cold impact test on the end fitting .13 5.5.2 Torsion 16 5.5.3 Tension .17 5.5.4 Compression .17 5.5.5 Bending.17 5.5.6 Torsion test of wing screw(s) .19 5.6 Dye penetration test 19 5.7 E

21、lectrical tests.19 5.7.1 Electrical test after water conditioning .19 5.7.2 Dielectric strength of internal insulation .21 5.8 Specific tests.23 5.8.1 Tie stick Tension test of the rotary blade and hook .23 5.8.2 Hook stick Operating rod functioning 24 5.8.3 Hook stick extension Tension strength of

22、the connecting clamp25 5.8.4 Wire holding stick Tightening capability 26 5.8.5 Pliers stick.27 5.8.6 Insulating oiler stick Functioning of the operating rod .28 5.8.7 Wire cutter stick Binding-wire cutter stick Cutting capability.29 5.8.8 Measuring stick .29 60832-1 IEC:2010 3 5.8.9 Tension puller (

23、dead-end tool).31 5.9 Instructions for use32 5.9.1 Type test .32 5.9.2 Alternative test in case of insulating sticks having completed the production phase.32 6 Conformity assessment of insulating sticks having completed the production phase .32 7 Modifications 32 Annex A (normative) Suitable for liv

24、e working; double triangle .33 Annex B (normative) Chronology of type tests .34 Annex C (normative) Classification of defects and associated tests .40 Annex D (informative) In-service recommendations .43 Bibliography46 Figure 1 Cold impact test on the end fitting 16 Figure 2 Bending test.18 Figure 3

25、 Electrical test after water conditioning20 Figure 4 Dielectric strength of internal insulation22 Figure 5 Tie stick Tension of the rotary blade23 Figure 6 Tie stick Tension of the rotary hook.24 Figure 7 Hook stick Operating rod functioning.25 Figure 8 Hook stick extension Tensile strength test for

26、 the connecting clamp26 Figure 9 Wire holding stick Tightening capability.26 Figure 10 Pliers stick Tightening capability .27 Figure 11 Pliers stick Torsion of the support handle27 Figure 12 Pliers stick Torsion of the operating handle .28 Figure 13 Insulating oiler stick Functioning of the operatin

27、g rod 29 Figure 14 Measuring stick Resistance to abrasion.30 Figure 15 Electrical test on type A tension puller31 Figure 16 Electrical test on type B tension puller32 Table 1 Mechanical characteristics of hand sticks (to be supplied by the manufacturer) .10 Table 2 Mechanical characteristics of supp

28、ort sticks (to be supplied by the manufacturer) .10 Table 3 Torque values and pass criteria of the torsion test.17 Table 4 Tensile forces and pass criteria of the tension test 17 Table 5 Compression forces and pass criteria of the compression test.17 Table 6 Bending forces and pass criteria of the b

29、ending test17 Table B.1 Type tests for hand sticks 34 Table B.2 Type tests for support sticks 38 Table C.1 Classification of defects and associated requirements and tests for hand sticks 40 Table C.2 Classification of defects and associated requirements and tests for support sticks .42 4 60832-1 IEC

30、:2010 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LIVE WORKING INSULATING STICKS AND ATTACHABLE DEVICES Part 1: Insulating sticks FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC N

31、ational Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Pu

32、blicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-gove

33、rnmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC

34、on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accept

35、ed by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote internationa

36、l uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latt

37、er. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users shoul

38、d ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damag

39、e of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of t

40、he referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights

41、. International Standard IEC 60832-1 has been prepared by IEC technical committee 78: Live working. The first edition of IEC 60832-1 and that of IEC 60832-2 cancel and replace the first edition of IEC 60832 published in 1988. The two parts have been created to clearly separate the requirements and t

42、esting of insulating sticks from those of attachable devices. Compared to IEC 60832, the major changes included in IEC 60832-1 are: integration of a cold impact test on the end fitting; creation of an electrical category of end fittings; integration of a test of the dielectric strength of internal i

43、nsulation; modification of the dye penetration test (disappearance of fuchsine); 60832-1 IEC:2010 5 application of conformity assessment for products having completed the production phase, according to IEC 61318:2007 (Edition 3), focusing on the classification of defects and the introduction of alte

44、rnative testing in case of production follow-up. The text of this standard is based on the following documents: FDIS Report on voting 78/838/FDIS 78/844/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This public

45、ation has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 60832 series, published under the general title Live working Insulating sticks and attachable devices, can be found on the IEC website. The committee has decided that the contents of this publica

46、tion will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60832-1 IEC:2010 INTRODUCTION Th

47、e purpose of this standard is to provide essential requirements. Each user may supplement it with their own requirements. For example, the user may add requirements regarding the use of insulating sticks on d.c. electrical installations or the mechanical performance or compatibility and interchangea

48、bility with tools already in service. In such cases, caution should be taken to maintain or improve the performance of the products. This publication has been prepared in accordance with the requirements of IEC 61477. The products designed and manufactured according to this standard contribute to th

49、e safety of the users provided they are used by skilled persons, in accordance with safe methods of work and the instructions for use. The product covered by this standard may have an impact on the environment during some or all stages of its life cycle. These impacts can range from slight to significant, be of short-term or long-te