NASM 1312-13-1997 Fastener Test Methods - Method 13 Double Shear Test.pdf

《NASM 1312-13-1997 Fastener Test Methods - Method 13 Double Shear Test.pdf》由会员分享，可在线阅读，更多相关《NASM 1312-13-1997 Fastener Test Methods - Method 13 Double Shear Test.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、NASM 1312-13-1997 Fastener Test Methods - Method 13 Double Shear Test_STD.AIA/NAS NASNIJIZ-IJ-ENGL 1,777 rn 0338743 0505403 177 m NASM1312-13 29 August 1997 ADOPTION NOTICE NASM 13 12- 13 , “Fastener Test Methods Method 13 Double Shear Test” was adopted on 29 August 1997 for use by the Department of

2、 Defense OD). Proposed changes by DoD activities must be submitted to the DoD Adopting Activity: Commander, Naval Air Warfare Center Aircraft Division, Code 4141OOB120-3 Highway 547, Lakehurst, NJ 08733-5100. DoD activities may obtain copies of this standard fiom the Standardization Document Order D

3、esk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19 1 1 1-5094. The private sector and other Government agencies may purchase copies from the Aerospace Industries Association, 1250 Eye Street W, Washington, DC 20005. NASM13 12-13 Should be used instead of MIL-STD-13 12-134 which was cancelled

4、on 29 August 1997. Custodians: Navy - AS Air Force - 1 1 Army - AV Preparing activity: Navy - AS (Project No. 53GP-0285-13) Review Activities: Navy - AS, SH Air Force - 1 1 Army - AV, AR DLA - IS COPYRIGHT Aerospace Industries Association of America, Inc. (AIA NAS)Licensed by Information Handling Se

5、rvicesSTD.AIA/NAS NASML332-33-ENGL 1997 Is 0338743 0505LOO 737 NATIONAL AEROSPACE STANDARD COPYRIGHT 1997 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC ALL RIGHTS RESERVED NASM1312-13 STANDARD PRACTICE FASTENER TEST METHODS METHOD 13 DOUBLE SHEAR TEST THE INITIAL RELEASE OF THIS DOCUMENT SUPERSED

6、ES MIL-STD-1312-13A DESIGNATION FOR THIS TEST METHOD REMAINS MIL-STD-13 12-13 LIST OF CURRENT SHEETS NO. 8 7 6 5 4 3 2 1 , REV. NEW NEW NEW NEW NEW NEW NEW NEW FSC 53GP SHEET 1 OF 8 APPROVAL DATE AUGUST 1997 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY AEROSPACE STANDARD IS ENTIRELY VOLUNTARY AIA DO

7、ES NOT QUALIW SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARK RIGHTS. COPYRIGHT Aerospace

8、Industries Association of America, Inc. (AIA NAS)Licensed by Information Handling Services- STD.AIA/NAS NASM1312-13-ENGL 1997 0318743 0505101 b73 NATIONAL AEROSPACE STANDARD COPYRIGHT 1997 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA INC ALL RIGHTS RESERVED NASM13 12-13 FOREWORD This standard sets fo

9、rth a standard test method to define the procedure and apparatus for testing fasteners in double shear in a half-hole shear fixture. SHEET 2 APPROVN. DATE AUGUST 1997 USE OF OR RELIANCE WON THIS DOCUMENT OR ANY AEROSPACE STANDARD IS ENTIRELY VOLUNTARY AIA DOES NOT QUAJ-lfl SUPPLIERS OR CERTIFY CONFO

10、RMANCE OF ITEMS PRODUCED UNDER AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SLJJTABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARK RIGHTS. COPYRIGHT Aerospace Industries Association of America, Inc.

11、 (AIA NAS)Licensed by Information Handling ServicesParagraph 1 1.1 2 . 2.1 2.1.1 2.2 3.0 4.0 4.1 4.1.1 4.1.2 4.1.3 5 . 5.1 5.1.1 5.1.2 5.1.3 6 . 6.1 NATIONAL AEROSPACE STANDARD COPYRIGHT 1997 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC ALL RIGHTS RESERVED TABLE OF CONTENTS NASM1312-13 . Sheet S

12、COPE . . 4 . Appllcablllty . 4 REFERENCED DOCUMENTS . 4 Government documents . . . 4 Specifications, standards and handbooks . 4 Other publications . 4 DEFINITIONS . 4 GENERAL REQUIREMENTS . 5 Test apparatus . 5 Test fixtures . 5 Grip length . 5 DETAILED REQUIREMENTS . 5 Test fixture . 5 Load rates

13、. 5 NOTES . 6 Testing machine . 5 Test procedures . 5 Test specimen . 5 I Test report . 6 FIGURES 1 . Double shear fixture . 7. TABLES I Double shear load rate . 6 SHEET 3 APPROVAL DATE AUGUST 1997 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY AEROSPACE STANDARD IS ENTIRELY VOLUNTARY AIA DOES NOT QUA

14、LIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER AEROSPACE STANDARDS . AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY TlIERETO OF PATENT OR TRADEMARK RIOHTS . COPYRIGHT Aerospace Indust

15、ries Association of America, Inc. (AIA NAS)Licensed by Information Handling Services1. NATIONAL AEROSPACE STANDARD COPYRIGHT 1997 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA. INC ALL RIGHTS RESERVED NASM1312-13 SCOPE 1.1 Applicabilitv. This test method covers the procedure and apparatus for testing

16、fasteners in double shear in a half-hole shear fixture. 2. REFERENCED DOCUMENTS 2.1 Government documents. 2.1.1 Specifications. standards and handbooks. The following specifications, standards and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified,

17、 the issues of these documents should be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and the supplement thereto, cited in the solicitation. SPECIFICATION MILITARY MIL-STD-45662 Calibration System Requirements (Copies of specifications, standa

18、rds and handbooks are available from the Naval Publications and Printing Service, Standardization Documents Ordering Desk, Bldg 4D, 700 Robbins Avenue, Philadelphia, PA 19 1 1 1-5094.) 2.2 Other publications. The following document(s) forms a part of this specification to the extent specified herein

19、. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DoDISS cited in the solicitation. Unless othedse specified, the issues of documents not listed in the DoDISS shall be the issues of the nongovernment documents which are current

20、on the date of the solicitation. AMERICAN SOCIETY FOR TESTING AND ,MATERIALS (ASTM) ASTM E 4 Standard Method of Verification of Testing Machines (Applications for copies should be addressed to the ASTM, 1916 Race Street, Philadelphia, PA 19103.) 3. DEFINITIONS (Not applicable) SHEET 4 APPROVAL DATE

21、AUGUST 1997 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY AEROSPACE STANDARD IS ENTIRELY VOLUNTARY AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICA

22、TION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARK RIGHTS. COPYRIGHT Aerospace Industries Association of America, Inc. (AIA NAS)Licensed by Information Handling Services STD.AIA/NAS NASM1312-L3-ENGL 2997 II 0318743 0505104 382 m NATIONAL AEROSPACE STANDARD COPYRIGHT 1997 AE

23、ROSPACE INDUSTRIES ASSOCIATION OF AMERICA INC ALL RIGHTS RESERVED NASM13 12-13 4. GENERALREQUIREMENTS. 4.1 Test apparatus. ,! 4.1.1 Testinp. machine. The testing machine shall be capable of applying a compressive load at a controllable rate. The calibrating system for the machine shall conform to MI

24、L-STD-45662. Its accuracy shall be verified every 12 months by a method complying with ASTM E4, using a calibration device which has been calibrated by the National Bureau of Standards not more than 2 years prior to its use. The loads of the fasteners tested shall be within the range of the testing

25、machine as defined in ASTM E4. 4.1.2 Test fixtures. Test fixtures shall be in accordance with Figure 1. 4,1.3 Grin IenHh. Unless otherwise specified, the minimum grip length of the test specimen shall be 3D. 5. DETAIL REQUIREMENTS 5.1 Test nrocedures. The ultimate double shear strength shall be obta

26、ined as follows: 5.1.1 Test Fixture. The fastener is placed in the receiving half-holes of the fixture base with neither threads nor fillet in bearing. 5.1.2 Test mecimen. The blade (guillotine) portion is placed in position on the specimen and the preload applied. 5.1.3 Load rates. The test loadis

27、then applied at a uniform rate as specified in table I. Load rates for larger or smaller size fasteners shall be calculated to give an initial stress rate of 100,000 pounds per minute per square inch of nominal double shear area. A tolerance of f 10 percent shall apply on the load rate. The nominal

28、double shear area is twice the nominal shank area for the load rate calculation i only. The test may be discontinued the ultimate load has been reached. and the specimen removed without a complete shear failure after SHEET 5 APPROVAL DATE AUGUST 1997 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY AERO

29、SPACE STANDARD IS ENTIRELY VOLUNTARY AIA DOES NOT QUNW SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (I) THE SUITABILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2) THE EXlSTENCE OF OR APPLICABILITY THERETO OF PATENT

30、OR TRADEMARK RIGHTS. COPYRIGHT Aerospace Industries Association of America, Inc. (AIA NAS)Licensed by Information Handling ServicesNATIONAL AEROSPACE STANDARD COPYRIGHT 1997 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC ALL RIGHTS RESERVED NASM13 12-13 TABLE I. Double shear load rates. Nominal 3

31、52,000 1 SOO 39,200 0.500 296,000 1.375 30,000 0.43 8 244,000 1.250 22,000 0.375 200,000 1.125 15,400 0.3 13 156,000 1 .o00 10,000 0.250 120,000 0.875 5,600 O. 188 88,000 0.750 4,200 0.164 6 1,200 0.625 , 3,840 O. 156 49,600 0.563 2,480 O. 125 Ib./min: diameter Ib./min. diameter Load iate Nominal Lo

32、ad rate The testing laboratory, at their option, may use a constant strain rate which will produce the specified load rate (f 10 percent) in the elastic range. That is, the strain rate shall be equal to the initial stress rate of 100,000 pounds per minute per square inch divided by the elastic modul

33、us in shear. 6. NOTES 6.1 Test report. Unless otherwise prescribed in the product specification, for the material being tested, the test report shall contain the following data: a. Fastener description. b. Part number. c. Material. d. Manufacturer. e. Measured diameter of each specimen. f. Individua

34、l ultimate load. I SHEET 6 APPROVAL. DATE AUGUST 1997 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY AEROSPACE STANDARD IS ENTIRELY VOLUNTARY AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITA

35、BILITY OF ITEMS FOR ANY PARTICULAR APPLICATION OR (2)THE EXISTENCE OF OR APPLICABILITY THERETO OF PATENT OR TRADEMARK RIGHTS. COPYRIGHT Aerospace Industries Association of America, Inc. (AIA NAS)Licensed by Information Handling ServicesNATIONAL AEROSPACE STANDARD COPYRIGHT 1997 AEROSPACE INDUSTRIES

36、ASSOCIATION OF AMERICA INC ALL RIGHTS RESERVED NASM1312-13 NOMINAL FASTENER SIZE o. 112 O. 125 O. 138 O. 156 O. 164 o. 188 o. 190 O. 250 0.313 0.375 0.438 O. 500 0.563 0.625 0.750 0.875 1.000 1.125 1.250 1 .37 5 1.500 MAX. 0.1130 O. 1260 O. 1390 0,1573 O. 1650 O. 1885 0.1910 0.2510 0.3135 0.3760 0.4

37、385 0.5010 O. 5635 O, 6260 0.7510 0.8760 1.0010 1.1260 1.2510 1.3760 1. so10 MIN. I -0.0000 I -0.0010 DO -. +0.0010 +o.oooo - -L 0.1123 O. 1253 O. 1383 O. 1566 O. 1643 0.1878 0.1903 0.2503 0.3128 0.3753 0.4378 O. 5003 0.5628 0.6253 0.7503 0.8753 1.0003 1.1253 1.2503 1.3753 1.5003 0.056 0.063 0.069 0

38、.078 0.082 0.094 O. 095 O. 125 0.156 o. 188 0.219 0.250 0.p1 0.313 0.375 0.438 O. 500 0.563 0.625 O. 688 0.750 o. 1120 O. 1250 O. 1380 O. 1563 0.1640 O. 1875 o I 1900 O. 2500 0.3125 0.3750 0.4375 O. 5000 O. 5625 0.6250 0.7500 0.8750 1 .o000 1.1250 1.2500 1.3750 1.5000 +0.0010 -0 .o000 T 0.1130 0.156

39、 0.1260 O. 156 1.531 1.5010 1.406 1.3760 1.281 1.2510, 1.156 1.1260 1.031 1.0010 0.906 0.8760 0.781 0.7510 0.656 0.6260 0.594 0.5635 0.531 0.5010 0.468 0.4385 0.406 0.3760 * 0.344 0.3135 0.281 0.2510 0.219 0.1910 0.219 0.1885 0.188 0.1650 O. 188 0.1573 O. 188 O. 1390 HQhS: 1. Break blade edges, 0.00

40、5 mlnlmum. Flxture shall be reworked when wear ,: results In chamfer or radlus of 0.010. In the event of controversy, .the blade edges shall be sharp. .i 2. For flxture slzes other than those listed, the government proportlons speclfled herein shall be malntalnrd. FIGURE 1. Double shear fixture. SHEET 7 APPROVAL DATE AUGUST 1997 USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY AEROSPACE STANDARD IS ENTlRELY VOLUNTARY AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY CONFORMANCE OF ITEMS PRODUCED UNDER AERO