VA 10 28 00-2011 TOILET BATH AND LAUNDRY ACCESSORIES.pdf

《VA 10 28 00-2011 TOILET BATH AND LAUNDRY ACCESSORIES.pdf》由会员分享，可在线阅读，更多相关《VA 10 28 00-2011 TOILET BATH AND LAUNDRY ACCESSORIES.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、11-11 10 28 00 - 1 SECTION 10 28 00 TOILET, BATH, AND LAUNDRY ACCESSORIES SPEC WRITER NOTE: 1. Delete between /_/ if not applicable to project. Also delete any other item or paragraph not applicable in the section and renumber the paragraphs. 2. Use this section for custom fabricated items in spaces

2、 listed. 3. Add items custom designed for these spaces. Verify items are detailed. 4. Verify that the drawings show the location and position of accessory items to be provided. Location of these items may be scheduled at the end of this section, however they must be shown on floor plans 5. Show on r

3、oom elevations dimension/location of accessories, including length and configuration of grab bars, towel bars, mirror sizes, and shelves. 6. See VA Standard details identified in list in parenthesis following item. Delete reference from project specification. 7. Coordinate to use same terminology us

4、ed in this section and on the drawings. PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies manufactured items usually used in dressing rooms, toilets, baths, locker rooms and at sinks in related spaces. B. Items Specified: 1. Paper towel dispenser. 2. Combination paper towel dispenser and di

5、sposal unit. 3. Waste receptacles. 4. Toilet tissue dispenser. 5. Grab Bars: (10800-1.DWG). 6. Shower curtain rods: (10800-2.DWG) and (10800-3.DWG). 7. Clothes hooks, robe or coat. 8. Towel bars. 9. Metal framed mirror: (10800-7.DWG). 10. Medicine cabinet. 11. Foot operated soap dispenser. 12. Soap

6、dishes. 13. Paper cup dispenser. 14. Mop racks. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-11-11 10 28 00 - 2 15. Stainless steel shelves, / Type 44 / Type 45 / Type 45C /. (10801-1.DWG) 16. Stainless steel shelves at wheelchair lavatory. B. Thi

7、s section also specifies custom fabricated items used in toilets and related spaces. 1.2 RELATED WORK A. Color of finishes: Section 09 06 00, SCHEDULE FOR FINISHES /B. Ceramic toilet and bath accessories: Section 09 30 13, CERAMIC TILING / C. Custom fabricated accessories: Section 10 28 00, TOILET,

8、BATH, AND LAUNDRY ACCESSORIES. /D. Shower curtain break away pendant chain hooks: Section 10 21 23, CUBICLES. / E. Color of vinyl fabric: Section 09 06 00, SCHEDULE FOR FINISHES. F. Manufactured toilet and bath accessories: Section 10 28 00, TOILET, BATH, AND LAUNDRY ACCESSORIES. 1.3 SUBMITTALS A. S

9、ubmit in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES. B. Shop Drawings: 1. Each product specified. 2. Paper towel dispenser and combination dispenser and disposal units. 3. Metal framed mirrors, showing shelf where required, fillers, and design and installation of unit

10、s when installed on ceramic tile wainscots and offset surfaces. 4. Shower Curtain rods, showing required length for each location. 5. Grab bars, showing design and each different type of anchorage. 6. Medicine cabinets showing design and installation. 7. Foot operated soap dispenser, showing anchora

11、ge and components. 8. Show material and finish, size of members, and details of construction, installation and anchorage of mop racks. C. Samples: 1. One of each type of accessory specified. 2. After approval, samples may be used in the work. D. Manufacturers Literature and Data: 1. All accessories

12、specified. 2. Show type of material, gages or metal thickness in inches, finishes, and when required, capacity of accessories. 3. Show working operations of spindle for toilet tissue dispensers. 4. Mop racks. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

13、HS-,-,-11-11 10 28 00 - 3 E. Manufacturers Certificates: 1. Attesting that soap dispensers are fabricated of material that will not be affected by liquid soap or aseptic detergents, Phisohex and solutions containing hexachlorophene. 2. Anodized finish as specified. 1.4 QUALITY ASSURANCE A. Each prod

14、uct shall meet, as a minimum, the requirements specified, and shall be a standard commercial product of a manufacturer regularly presently manufacturing items of type specified. B. Each accessory type shall be the same and be made by the same manufacturer. C. Each accessory shall be assembled to the

15、 greatest extent possible before delivery to the site. D. Include additional features, which are not specifically prohibited by this specification, but which are a part of the manufacturers standard commercial product. 1.5 PACKAGING AND DELIVERY A. Pack accessories individually to protect finish. B.

16、 Deliver accessories to the project only when installation work in rooms is ready to receive them. C. Deliver inserts and rough-in frames to site at appropriate time for building-in. D. Deliver products to site in sealed packages of containers; labeled for identification with manufacturers name, bra

17、nd, and contents. 1.6 STORAGE A. Store products in weathertight and dry storage facility. B. Protect from damage from handling, weather and construction operations before, during and after installation in accordance with manufacturers instructions. 1.7 APPLICABLE PUBLICATIONS A. Publications listed

18、below form a part of this specification to the extent referenced. Publications are referenced in the text by the basic designation only. B. American Society for Testing and Materials (ASTM): A167-99(R2009) . Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet and Strip. A176-99(R2009) .

19、Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip A269-10 Seamless and Welded Austenitic Stainless Steel Tubing for General Service Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-11-11 10 28 00 - 4 A312/A312M-09 Seamless and Welded

20、 Austenitic Stainless Steel Pipes A653/A653M-10 Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process B221-08 Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Shapes, and Tubes B456-03(R2009) . Electrodeposited Coatings of Copper Plus Nickel Plus

21、 Chromium and Nickel Plus Chromium C1036-06 . Flat Glass C1048-04 . Heat-Treated Flat Glass-Kind HS, Kind FT Coated and Uncoated Glass D635-10 Rate of Burning and/or Extent and Time of Burning of Self Supporting Plastics in a Horizontal Position F446-85(R2009) . Consumer Safety Specification for Gra

22、b Bars and Accessories Installed in the Bathing Area. D3453-07 . Flexible Cellular Materials - Urethane for Furniture and Automotive Cushioning, Bedding, and Similar Applications D3690-02(R2009) Vinyl-Coated and Urethane-Coated Upholstery Fabrics C. The National Association of Architectural Metal Ma

23、nufacturers (NAAMM): AMP 500 Series . Metal Finishes Manual D. American Welding Society (AWS): D10.4-86 (R2000) . Welding Austenitic Chromium-Nickel Stainless Steel Piping and Tubing E. Federal Specifications (Fed. Specs.): A-A-3002 . Mirrors, Glass FF-S-107C (2) Screw, Tapping and Drive FF-S-107C S

24、crew, Tapping and Drive. WW-P-541E(1) . Plumbing Fixtures (Accessories, Land Use) Detail Specification PART 2 - PRODUCTS SPEC WRITER NOTE: 1. Make material requirements agree with applicable requirements specified in the referenced Applicable Publications. 2. Update and specify only that which appli

25、es to the project. 2.1 MATERIALS A. Aluminum: ASTM B221, alloy 6063-T5 and alloy 6463-T5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-11-11 10 28 00 - 5 B. Stainless Steel: 1. Plate or sheet: ASTM A167, Type 302, 304, or 304L, except ASTM A176 wh

26、ere Type 430 is specified, 0.0299-inch thick unless otherwise specified. 2. Tube: ASTM A269, Alloy Type 302, 304, or 304L. C. Stainless Steel Tubing: ASTM A269, Grade 304 or 304L, seamless or welded. D. Stainless Steel Pipe: ASTM A312; Grade TP 304 or TP 304L. E. Steel Sheet: ASTM A653, zinc-coated

27、(galvanized) coating designation G90. F. Glass: 1. ASTM C1036, Type 1, Class 1, Quality q2, for mirrors, and for mirror doors in medicine cabinets. 2. ASTM C1036, Type 1 Class 1 Quality q3, for shelves in medicine cabinets. 3. ASTM C1048, Kind FT, Condition A, Type 1, Class 1 (use in Mental Health a

28、nd Behavior Nursing Unit Psychiatric Patient Areas and Security Examination Rooms where mirrors and glass are specified). G. Foam Rubber: ASTM D3453, Grade BD, Type 2. H. Vinyl Covering: ASTM D3690, Vinyl coated fabric, Class A. I. Plywood: PS1, Grade CD. 2.2 FASTENERS A. Exposed Fasteners: Stainles

29、s steel or chromium plated brass, finish to match adjacent surface. B. Concealed Fasteners: Steel, hot-dip galvanized (except in high moisture areas such as showers or bath tubs use stainless steel). C. Toggle Bolts: For use in hollow masonry or frame construction. D. Hex bolts: For through bolting

30、on thin panels. E. Expansion Shields: Lead or plastic as recommended by accessory manufacturer for component and substrate for use in solid masonry or concrete. F. Screws: 1. ASME B18.6.4. 2. Fed Spec. FF-S-107, Stainless steel Type A. G. Adhesive: As recommended by manufacturer for products to be j

31、oined. 2.3 FINISH A. In accordance with NAAMM AMP 500 series. B. Anodized Aluminum: 1. /AA-C22A41/ Chemically etched medium matte, with clear anodic coating, Class I Architectural, 0.7-mil thick./ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-11-11

32、 10 28 00 - 6 2. /AA-C22A44/Chemically etched medium matte with electrolytically deposited metallic compound, integrally colored coating Class I Architectural, 0.7-mil thick finish. Dyes will not be accepted./ C. / AA-M32 / Mechanical finish, medium satin. / 1. Chromium Plating: ASTM B456, satin or

33、bright as specified, Service Condition No. SC2. 2. Stainless Steel: NAAMM AMP 503, finish number 4. 3. Ferrous Metal: a. Shop Prime: Clean, pretreat and apply one coat of primer and bake. b. Finish: Over primer apply two coats of alkyd or phenolic resin enamel, and bake. 4. Nylon Coated Steel: Nylon

34、 coating powder formulated for a fluidized bonding process to steel to provide a hard smooth, medium gloss finish, not less than 0.3 mm (0.012-inch) thick, rated as self-extinguishing when tested in accordance with ASTM D635. 2.4 FABRICATION - GENERAL A. Welding, AWS D10.4. B. Grind dress, and finis

35、h welded joints to match finish of adjacent surface. C. Form exposed surfaces from one sheet of stock, free of joints. D. Provide steel anchors and components required for secure installation. E. Form flat surfaces without distortion. Keep exposed surfaces free from scratches and dents. Reinforce do

36、ors to prevent warp or twist. F. Isolate aluminum from dissimilar metals and from contact with building materials as required to prevent electrolysis and corrosion. G. Hot-dip galvanized steel, except stainless steel, anchors and fastening devices. H. Shop assemble accessories and package with all c

37、omponents, anchors, fittings, fasteners and keys. I. Key items alike. J. Provide templates and rough-in measurements as required. K. Round and deburr edges of sheets to remove sharp edges. 2.5 PAPER TOWEL DISPENSERS A. Surface mounted type with sloping top. B. Dispensing capacity for 300 sheets of a

38、ny type of paper toweling. C. Fabricate of stainless steel. D. Provide door with continuous hinge at bottom, and either spring tension cam lock or tumbler lock, keyed alike, at top and a refill sight slot in front. 2.6 COMBINATION PAPER TOWEL DISPENSER AND DISPOSAL UNITS A. / Recessed / and / semi-r

39、ecessed / type. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-11-11 10 28 00 - 7 B. Dispensing capacity for 400 sheets of any type of paper toweling. C. Fabricate of stainless steel. D. Form face frames, from one piece. E. Provide each door with co

40、ntinuous stainless steel piano hinge and tumbler lock, keyed alike. F. Provide removable waste receptacle approximately 40 liter (10.5 gallon) capacity, fabricated of 0.45 mm (0.018-inch) thick stainless steel. 2.7 WASTE RECEPTACLES A. Semi-recessed type, without doors. Fed. Spec WW-P-541, Type II.

41、B. Fabricate of stainless steel. C. Form face frame from one piece. D. Provide removable waste receptacle of approximately (12 gallon) capacity, fabricated of stainless steel. E. Waste receptacle key locked in place. 2.8 TOILET TISSUE DISPENSERS A. Double roll surface mounted type. B. Mount on conti

42、nuous backplate. C. Removable spindle ABS plastic or chrome plated plastic. D. Wood rollers are not acceptable. 2.9 GRAB BARS A. Fed. Spec WW-P-541/8B, Type IV, bars, surface mounted, Class 2, grab bars and ASTM F446. B. Fabricate of either stainless steel or nylon coated steel, except use only one

43、type throughout the project: 1. Stainless steel: Grab bars, flanges, mounting plates, supports, screws, bolts, and exposed nuts and washers. 2. Nylon Coated Steel: Grab bars and flanges complete with mounting plates and fasteners. /Color is specified under Section 09 06 00, SCHEDULE FOR FINISHES. /

44、C. Concealed mount, except grab bars mounted at floor, swing up and on metal / toilet / dressing / shower / partitions. D. Bars: 1. Fabricate from 38 mm (1-1/2 inch) outside diameter tubing. a. Stainless steel, minimum 1.2 mm (0.0478 inch) thick. b. Nylon coated bars, minimum 1.5 mm (0.0598 inch) th

45、ick. 2. Fabricate in one continuous piece with ends turned toward walls, except swing up and where grab bars are shown continuous around three sides of showers, bars may be fabricated in two sections, with concealed slip joint between. 3. Continuous weld intermediate support to the grab bar. Provide

46、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-11-11 10 28 00 - 8 4. Swing up bars manually operated. Designed to prevent bar from falling when in raised position. E. Flange for Concealed Mounting: 1. Minimum of 2.65 mm (0.1046 inch) thick, approximately 7

47、5 mm (3 inch) diameter by 13 mm (1/2 inch) deep, with provisions for not less than three set screws for securing flange to back plate. 2. Insert grab bar through center of the flange and continuously weld perimeter of grab bar flush to back side of flange. F. Flange for Exposed Mounting: 1. Minimum

48、5 mm (3/16 inch) thick, approximately 75 mm (3 inch) diameter. 2. Insert grab bar through flange and continuously weld perimeter of grab bar flush to backside of flange. 3. Where mounted on metal / toilet / dressing / shower / partitions, provide three equally spaced, countersunk holes, sized to acc

49、ommodate 5 mm (3/16 inch) diameter bolts. 4. Where mounted on floor, provide four equally spaced holes, sized to accommodate 5 mm (3/8 inch) diameter bolts, not more than 5 mm (3/8 inch) from edge of flange. G. In lieu of providing flange for concealed mounting, and back plate as specified, grab rail may be secured by being welded to a back plate and b