UOP 824-1981 DIETHANOLAMINE IN SOLUTIONS BY COLOR INDICATOR TITRATION.pdf

《UOP 824-1981 DIETHANOLAMINE IN SOLUTIONS BY COLOR INDICATOR TITRATION.pdf》由会员分享，可在线阅读，更多相关《UOP 824-1981 DIETHANOLAMINE IN SOLUTIONS BY COLOR INDICATOR TITRATION.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、DIETHANOLAMINE IN SOLUTIONSBY COLOR INDICATOR TITRATIONUOP Method 824-81SCOPEThis control method is used for the analysis of diethanolamine (DEA) in solutions used to remove acidgases, such as hydrogen sulfide and carbon dioxide from hydrocarbon streams. The method utilizes an acid-base titration th

2、at determines basic constituents, i.e., free amine and amine associated with weak acids. Thevalue obtained is a measure of the potential efficiency of the solution to remove the above gases. The lowerlimit of detection is less than 1 wt-%.OUTLINE OF METHODThe amine sample is diluted with water and t

3、itrated with a standard sulfuric acid solution to the methylred indicator endpoint.APPARATUSBeaker, 250-mLBuret, 50-mL, with Teflon stopcock, 0.1-mL subdivisionsCylinder, graduated, 100-mL, glass, 1.0-mL subdivisionsHot plate, adjustable head, Sargent-Welch Scientific Co., Cat. No. S-41000 A, or equ

4、ivalentPipet, serological, calibrated for blow-out, one-milliliter capacity, Sargent-Welch Scientific Co., Cat. No.S-69625-C, or equivalentPipet manipulator, Sargent-Welch Scientific Co., Cat. No. S-69793, or equivalentStirrer, magnetic, with Teflon-covered stirring bar, Sargent-Welch Scientific Co.

5、, Cat. No. S-76490, orequivalentREAGENTSAll reagents shall conform to the specifications established by the Committee on Analytical Reagents ofthe American Chemical Society, when such specifications are available, unless otherwise specified.References to water mean deionized or distilled water.Methy

6、l red indicator solution, 0.1 wt-% concentration. Dissolve 0.1 g of methyl red in 100 g of water.IT IS THE USERS RESPONSIBILITY TO ESTABLISH APPROPRIATE PRECAUTIONARY PRACTICES AND TODETERMINE THE APPLICABILITY OF REGULATORY LIMITATIONS PRIOR TO USE. EFFECTIVE HEALTH ANDSAFETY PRACTICES ARE TO BE FO

7、LLOWED WHEN UTILIZING THIS PROCEDURE. FAILURE TO UTILIZE THISPROCEDURE IN THE MANNER PRESCRIBED HEREIN CAN BE HAZARDOUS. MATERIAL SAFETY DATA SHEETS(MSDS) OR EXPERIMENTAL MATERIAL SAFETY DATA SHEETS (EMSDS) FOR ALL OF THE MATERIALS USED INTHIS PROCEDURE SHOULD BE REVIEWED FOR SELECTION OF THE APPROP

8、RIATE PERSONAL PROTECTIONEQUIPMENT (PPE). COPYRIGHT 1981 UOP LLCALL RIGHTS RESERVEDUOP Methods are available through ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken PA 19428-2959,United States. The Methods may be obtained through the ASTM website, www.astm.org, or by contac

9、ting Customer Service atserviceastm.org, 610.832.9555 FAX, or 610.832.9585 PHONE.2 of 2824-81Sulfuric acid solution, aqueous, 0.05-M, standardizedPROCEDUREBecause of the potential hazards resulting from the liberation of gaseous H2S during this analysis, arrangethe apparatus in an efficient hood. Pi

10、pet one milliliter of the amine solution sample into a beaker containing100 mL of water and a magnetic stirring bar. Remove any remaining sample from the pipet into the waterby blowing into the pipet. With viscous samples, rinse the pipet into the beaker with water. Add 3 drops ofmethyl red indicato

11、r solution to the sample solution and turn on the magnetic stirrer. Titrate the samplesolution with standard 0.05 M sulfuric acid to a definite pink endpoint. Place the beaker on the hot plate andheat to boiling for one minute. If the solution remains pink, use the first endpoint. If the solution tu

12、rnsyellow, cool the solution and titrate again to a definite pink endpoint. Take the final reading for the totalvolume of titrant used.In the titration of samples containing H2S, if the color of the methyl red indicator is destroyed, moreindicator should be added during the titration. A lean (regene

13、rated), as opposed to rich, amine solutionshould be analyzed whenever possible since the presence of H2S and CO2tends to make the methyl redendpoint less definite.CALCULATIONSCalculate the concentration of diethanolamine in the sample solution as follows:21.0 AMDiethanolamine, g/100 ml V=where:A = s

14、tandard sulfuric acid solution, mLM = molarity of sulfuric acid solutionV = sample volume, mL21.0 AMDiethanolamine, wt - % SV=where:S = specific gravity of sample, 60/60 F (15.6/15.6 C)A, M and V are as previously definedPRECISIONAn estimated standard deviation is not reported since insufficient dat

15、a are available at present to permitthis calculation with at least 4 degrees of freedom. It is estimated that duplicate analyses should agreewithin 0.1 g/100 mL or 0.1 wt-%.TIME FOR ANALYSESThe elapsed time for one analysis is 1.0 hour. The labor requirement is 0.5 hour.REFERENCEMethod SM-1D, The Girdler Corp., Louisville, KYSUGGESTED SUPPLIERSargent-Welch Scientific Co., 7300 N. Linder Ave., Skokie, IL 60076