UL SUBJECT 4041-2018 UL Outline for Investigation Outdoor Furniture (Issue 1).pdf

《UL SUBJECT 4041-2018 UL Outline for Investigation Outdoor Furniture (Issue 1).pdf》由会员分享，可在线阅读，更多相关《UL SUBJECT 4041-2018 UL Outline for Investigation Outdoor Furniture (Issue 1).pdf（134页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJUNE 29, 20181UL 4041Outline of Investigation for Outdoor FurnitureIssue Number: 1June 29, 2018Summary of TopicsThis first issue of the Outline of Investigation for Outdoor Furniture, UL4041, pro

2、vides requirements for construction and testing of outdoor patiofurniture such as tables, tables with umbrellas, chairs, multi-seatproducts, loveseats, benches, hanging chairs or swings and chaiselounge chair.ULs Outlines of Investigation are copyrighted by UL. Neither a printed norelectronic copy o

3、f an Outline of Investigation should be altered in any way. All ofULs Outlines of Investigation and all copyrights, ownerships, and rights regardingthose Outlines of Investigation shall remain the sole and exclusive property of UL.Parts of the text and figures (Top load ease cycle test, Concentrated

4、 load tests,Distributed load tests, Leg strength test, Test for tables with casters) have beenadapted by UL from BIFMA X5.5, Desk Products, with permission from theBusiness and Institutional Furniture Manufacturers Association (BIFMA).Parts of the text and figures (Stability disk construction detail

5、s, Stability tests Rear and Front, Backrest Strength test Static Type I, II and III, Drop test Dynamic, Swivel Test Cyclic, Seating Durability tests, Arm Strength test Vertical - Static, Arm Strength test Horizontal- Static, Backrest Durability Test Cyclic Type I, II and III, Caster/chair base Durab

6、ility test, Leg Strength Test Front and Side Application, Footrest Static Load Test Vertical, FootrestDurability Test Vertical Cyclic have been adapted by UL from BIFMA X5.1,Office Seating, and BIFMA X5.4, Lounge and Public Seating, with permissionfrom the Business and Institutional Furniture Manufa

7、cturers Association (BIFMA).COPYRIGHT 2018 UL LLCUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJUNE 29, 2018UL 40412No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL

8、CONTENTSINTRODUCTION1 Scope .82 General 82.1 Units of measurement .82.2 Undated references .82.3 Note on figures 82.4 Tolerance .83 Glossary .9CONSTRUCTION4 General .135 Protection Against Corrosion 15PERFORMANCE6 Welding .167 General .188 Horizontal Glass Impact Test 218.1 Applicability .218.2 Purp

9、ose of test 218.3 Test setup 218.4 Test procedure 218.5 Compliance criteria 229 Vertical Glass Impact Test 229.1 Applicability .229.2 Purpose of test 229.3 Test setup 229.4 Test procedure 229.5 Compliance criteria 2210 Shear and Pinch Point Test 2210.1 Applicability 2210.2 Purpose of test 2210.3 Tes

10、t setup .2310.4 Test procedure .2310.5 Compliance criteria .23TABLE TESTING11 Stability Test .2311.1 General .2311.2 Table stability Tables designed to support an umbrella 2412 Top Load Ease Cycle Test .2512.1 Applicability 2512.2 Purpose of test 2612.3 Test setup .2612.4 Test procedure .2612.5 Comp

11、liance criteria .2713 Concentrated Load Test .27JUNE 29, 2018 UL 4041 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL13.1 Normal (Functional) load test 2713.2 Concentrated abnormal (Proof) load test 2914 Distributed Load Test .2914.1 Normal

12、(Functional) load test 2914.2 Distributed abnormal (Proof) load test .3115 Table Unit Drop Test 3115.1 Applicability 3115.2 Purpose of test 3215.3 Test setup .3215.4 Test procedure .3215.5 Compliance criteria .3216 Leg Strength Test .3216.1 Applicability 3216.2 Purpose of test 3216.3 Test setup .321

13、6.4 Normal (Functional) test .3316.5 Abnormal (Proof) test .3817 Test for Tables with Casters .3817.1 Applicability 3817.2 Purpose of test 3817.3 Test setup .3817.4 Test procedure .4117.5 Compliance criteria .41CHAIR TESTING18 Stability Tests 4118.1 Applicability 4118.2 Purpose of test 4118.3 Stabil

14、ity disk .4118.5 Front stability 4819 Backrest Strength Test Static Type I and II .5619.1 Applicability 5619.2 Purpose of test 5719.3 Test setup .5719.4 Test procedures 6019.5 Conformance criteria 6120 Backrest Strength Test Static Type III .6120.1 Applicability 6120.2 Purpose of test 6120.3 Test se

15、tup .6120.4 Test procedures 6420.5 Conformance criteria 6521 Drop Test Dynamic 6521.1 Applicability 6521.2 Purpose of test 6521.3 Test setup .6521.4 Test procedures 6721.5 Compliance criteria .6822 Swivel Test Cyclic .6822.1 Applicability 6822.2 Purpose of test 6922.3 Test setup .69JUNE 29, 2018UL 4

16、0414UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL22.4 Test procedure .7022.5 Conformance criteria 7023 Seating Durability Tests Cyclic 7023.1 Applicability 7023.2 Test purpose 7023.3 Impact test 7023.4 Front corner load-ease test Cyclic Off

17、-center .7423.5 Conformance criteria 7424 Arm Strength Test Vertical Static 7524.1 Applicability 7524.2 Test purpose 7524.3 Test setup .7524.4 Test procedures 7524.5 Compliance criteria .7625 Arm Strength Test Horizontal Static .7825.1 Applicability 7825.2 Test purpose 7825.3 Test setup .7825.4 Test

18、 procedures 7825.5 Compliance criteria .7926 Backrest Durability Test Cyclic Type l 8026.1 Applicability 8026.2 Purpose of test 8026.3 Test setup .8026.4 Test procedures 8126.5 Compliance criteria .8227 Backrest Durability Test Cyclic Type Il and lll .8627.1 Applicability 8627.2 Purpose of test 8627

19、.3 Test setup .8627.4 Test procedure .8827.5 Compliance criteria .8928 Caster/Chair Base Durability Test for Pedestal Base Chairs 8928.1 Applicability 8928.2 Purpose of test 9128.3 Test setup .9128.4 Test procedure .9228.5 Conformance criteria 9229 Caster/Chair Frame Durability Test for Chairs with

20、Legs .9229.1 Applicability 9229.2 Purpose of test 9229.3 Test setup .9229.4 Test procedure .9429.5 Conformance criteria 9430 Leg Strength Test Front and Side Application 9430.1 Applicability 9430.2 Purpose of test 9530.3 Front load test .9530.4 Side load test 9630.5 Conformance criteria Front and si

21、de load tests .9831 Footrest Static Load Test Vertical .9831.1 Applicability 9831.2 Purpose of test 98JUNE 29, 2018 UL 4041 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL31.3 Test setup .9831.4 Static load test Normal (functional) load .983

22、1.5 Static load test Abnormal (proof) load .9932 Footrest Durability Test Vertical Cyclic 10032.1 Applicability .10032.2 Purpose of test .10032.3 Test setup 10032.4 Test procedure .10032.5 Conformance criteria 100CHAISE LOUNGE CHAIR TESTING33 Chaise Lounge Chair .10133.1 Stability 10133.2 Backrest s

23、trength test Static 10733.3 Drop test Dynamic .10934 Seating Durability Tests Cyclic 11234.1 Applicability .11234.2 Purpose of test .11234.3 Test setup 11234.4 Test procedure .11334.5 Compliance criteria 11335 Arm Strength Test Vertical Static .11335.1 Applicability .11335.2 Test purpose .11335.3 Te

24、st setup 11335.4 Test procedures 11435.5 Compliance criteria 11436 Arm Strength Test Horizontal Static 11436.1 Applicability .11436.2 Test purpose .11436.3 Test setup 11436.4 Test procedures 11536.5 Compliance criteria 11537 Backrest Durability Test Cyclic 11537.1 Applicability .11537.2 Purpose of t

25、est .11537.3 Test setup 11537.4 Test procedure .11637.5 Compliance criteria 11738 Leg Strength Test Front and Side Application .11738.1 Applicability .11738.2 Front load test 11838.3 Side load test .11939 Lifting Test for Mobile Chaise Lounge Chair 12039.1 Applicability .12039.2 Purpose of test .120

26、39.3 Test setup 12039.4 Test procedure .12039.5 Compliance criteria 121JUNE 29, 2018UL 40416UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULMARKINGS40 General 121INSTRUCTIONS41 General 122Appendix A Test method and requirement for Swing or Han

27、ging chairsA1 Front and Rear Stability Test for Hanging Chairs .A1A1.1 Applicability .A1A1.2 Purpose of test A1A1.3 Test setup A1A1.4 Test procedure A1A1.5 Compliance criteria .A1A2 Static Load Test of Seat A1A2.1 Applicability .A1A2.2 Purpose of test A2A2.3 Test setup A2A2.4 Test procedure A2A2.5 C

28、ompliance criteria .A2A3 Durability Load Test of Seat (Alternative Method to: Seating Durability Tests Cyclic) .A3A3.1 Applicability .A3A3.2 Purpose of test A3A3.3 Test setup A3A3.4 Test procedure A3A3.5 Compliance criteria .A4A4 Structural Strength Test of the Swing (Alternative Method to: Leg Stre

29、ngth Test Front and SideApplication) .A4A4.1 Applicability .A4A4.2 Purpose of test A4A4.3 Test setup A4A4.4 Test procedures .A6A4.5 Compliance criteria Front and side load tests A6A5 Oscillation Fatigue Test (Additional Test for Seating with Oscillation Motion) .A6A5.1 Applicability .A6A5.2 Purpose

30、of test A6A5.3 Test setup A6A5.4 Test procedures .A9A5.5 Compliance criteria .A9JUNE 29, 2018 UL 4041 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULINTRODUCTION1 Scope1.1 This outline of investigation provides requirements for construction

31、and testing of outdoor patiofurniture such as tables, tables with umbrellas, chairs, multi-seat products, loveseats, benches, hangingchairs or swings and chaise lounge chair. Indoor furniture or outdoor furniture with electrical componentsshould reference the Standard for Household and Commercial Fu

32、rnishings, UL 962.2 General2.1 Units of measurement2.1.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory orapproximate information.2.2 Undated references2.2.1 Any undated reference to a code or standard appearing in the requirements of this outline ofinve

33、stigation shall be interpreted as referring to the latest edition of that code or standard.2.3 Note on figures2.3.1 Figures provided in this outline are intended as guidelines only and not representative of all possibletest configurations.2.4 Tolerance2.4.1 Unless otherwise specified, tolerances sha

34、ll be:a) Test Weights, Forces, Velocities, Time, and Cycle requirements are minimums;b) Linear measurements, 1.5 mm (1/16 in);c) Angles, 5 degrees; andd) Level, within 5 mm per meter (0.06 in per linear foot) or 0.3 degrees.Test weights, forces, dimensions, angles, times, rates and velocities used t

35、o perform the test shall betargeted at the nominal values specified and shall be subject to the above tolerances. Devices used tocalibrate test devices and/or machines shall be calibrated to one-fourth of the above tolerance, with theexception of Level, which shall be calibrated to one-half.JUNE 29,

36、 2018UL 40418UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL3 Glossary3.1 For the purpose of this outline, the following definitions apply.3.2 AUTOMATIC LOCKING MECHANISM Mechanism which engages without guidance by the userand prevents uninte

37、nded movement.3.3 BENCH a piece of furniture used for seating that usually holds more than one person.3.4 CHAIR TYPES:a) CHAIR TYPE I: TILTING CHAIR A chair with a seat and backrest that tilt (either in unisonor in synchronization) with a counterbalancing force. See Figure 3.1.b) CHAIR TYPE II: FIXE

38、D SEAT ANGLE, TILTING BACKREST A chair that provides a fixedseat angle with a tilting backrest. See Figure 3.2.c) CHAIR TYPE III: FIXED SEAT ANGLE, FIXED BACKREST A chair that provides a fixedseat angle with a fixed backrest. See Figure 3.3.d) CHAISE LOUNGE CHAIR Chaise lounge chair is any long recl

39、ining chair with seat longenough to support the stretched legs. It has an angular back support as shown in Figure 3.4.This is generated text for figtxt.Figure 3.1Type I Tilting ChairJUNE 29, 2018 UL 4041 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSI

40、ON FROM ULFigure 3.2Type II Fixed seat angle, tilting backrestFigure 3.3Type III Fixed seat angle, fixed backrestJUNE 29, 2018UL 404110UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL3.5 CHAISE LOUNGE SEAT LOADING POINTAApoint 175 mm (6.9 in)

41、forward of the seat/backjunction on the longitudinal axis of the chaise lounge chair, or the point closest to this that allows the seatforce to be applied.3.6 CMD The BIFMA Chair Measuring Device used for the measurement of seating products.3.7 CYCLE A complete sequence of operation. This could incl

42、ude loading and unloading, stressreversal; opening and closing; or one complete revolution.3.8 FORCE A vector quantity, expressed in newton (N) or pounds force (lbf) that is an interaction withan object.3.9 FORM FITTING DEVICE A device that distributes a force over a 305 13 mm 89 13 mm (120.5 in 3.5

43、 0.5 in) area of a backrest. The device will be shaped to approximate the contours of thechair backrest.3.10 GANGED SEATING UNITS Multiple seating position units that are made of individual (single seat)units that are mechanically connected.3.11 LOAD The weight to which a structure is subjected; a w

44、eight or force applied to a product; forceacting on a surface, usually caused by the action of gravity.Figure 3.4Chaise lounge chairJUNE 29, 2018 UL 4041 11UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL3.12 LOAD-BEARING STRUCTURE/SURFACE Any

45、 element that supports loads during use. Foam andfabric, for example, are not generally considered load-bearing surfaces, nor are some portions of waterfalledges.3.13 LOSS OF SERVICEABILITY The failure of the product to support its intended load or to performall of its normal functions or adjustment

46、s.3.14 MULTIPLE SEATING Seating that has seating positions provided for more than one person.3.15 NORMAL USE CONDITION For consistency, the midpoint of any adjustment range, such as theheight adjustment or counter balancing force adjustment unless otherwise specified in the test method.3.16 PEDESTAL

47、 BASE A base that supports a chair by a single central structural member such as acolumn.3.17 ROCKING MOTION Move gently to and fro.3.18 SEAT OR SEATING POSITION The portion(s) of a unit intended for sitting, approximately 570 mm(22.5 in) in width. Attached table surfaces are not considered seating

48、positions. The number of seatingpositions shall be as specified by the manufacturer. If no manufacturers specification is available, or if thenumber of seating positions is not clearly defined by the design or contours of the seating surface (i.e.bench-type seating units), the number of seating posi

49、tions shall be determined as follows: divide the widthof the seating surface by 570 mm (22.5 in). To determine the number of seating positions round the resultdown to the nearest integer.3.19 SHEAR AND SQUEEZE POINT Shear and pinch points exist when the accessible parts are closeenough to each other to create a shear point or a pinch point. If two parts can move to create an openingthat vary its dimensions from more than 7