UL 810A-2008 UL Standard for Safety Electrochemical Capacitors (First Edition Reprint with Revisions Through and Including March 28 2017)《电化学电容器》.pdf

《UL 810A-2008 UL Standard for Safety Electrochemical Capacitors (First Edition Reprint with Revisions Through and Including March 28 2017)《电化学电容器》.pdf》由会员分享，可在线阅读，更多相关《UL 810A-2008 UL Standard for Safety Electrochemical Capacitors (First Edition Reprint with Revisions Through and Including March 28 2017)《电化学电容器》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 810A Electrochemical CapacitorsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER RE

2、PRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Electrochemical Capacitors, UL 810A First Edition, Dated October 7, 2008 Summary of Topics The revision dated November 1, 2012 was issued to incorporate the addition of a denition for Electrochemical Capacitors, 5.7A. T

3、ext that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on whi

4、ch the changed requirement becomes effective. The revised requirements are substantially in accordance with Proposal(s) on this subject dated September 21, 2012. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means,

5、 electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will

6、UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possi

7、bility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, l

8、iability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections,

9、 tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQU

10、IREMENTS notice. NOVEMBER 1, 2012 UL 810A tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NOVEMBER 1, 2012 UL 810A tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION

11、FROM UL OCTOBER 7, 2008 (Title Page Reprinted: November 1, 2012) 1 UL 810A Standard for Electrochemical Capacitors First Edition October 7, 2008 This ANSI/UL Standard for Safety consists of the First Edition including revisions through November 1, 2012. The most recent designation of ANSI/UL 810A as

12、 an American National Standard (ANSI) occurred on November 1, 2012. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposal

13、s should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownershi

14、ps, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2012 UNDERWRITERS LABORATORIES INC. ANSI/UL 810A-2012UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 7, 2008 ELECTROCHEMICAL CAPAC

15、ITORS - UL 810A 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 Units of Measurement .5 3 Undated References 5 4 Components 5 5 Glossary .6 CONSTRUCTION 6 Casing/Enclosure .7 6.1 Gener

16、al .7 6.2 Metallic 7 6.3 Nonmetallic 8 7 Insulating Materials 9 8 Insulated Leads and Terminals .9 9 Spacings 10 PERFORMANCE 10 Important Test Considerations 10 11 Termination Tests .11 11.1 Pull-out test .11 11.2 Torque test 11 12 Conditioning 12 12.1 General .12 12.2 Charge/Discharge cycling condi

17、tioning 13 12.3 Temperature cycling conditioning .13 12.4 Oven exposure conditioning .14 13 Short-Circuit at 55C Test 14 14 Abnormal Charge Test 15 15 Normal Temperature Test 16 16 Heating Test .17 17 Dielectric Voltage-Withstand Test .17 18 Mechanical Tests .18 18.1 General .18 18.2 Crush test .18

18、18.3 Impact test 18 18.4 Shock test .19 18.5 Vibration test 19 MANUFACTURING AND PRODUCTION TESTS 19 Dielectric Voltage-Withstand .20 MARKINGS 20 General 21 OCTOBER 7, 2008 ELECTROCHEMICAL CAPACITORS - UL 810A 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT P

19、ERMISSION FROM UL INSTRUCTIONS 21 General 21 OCTOBER 7, 2008 ELECTROCHEMICAL CAPACITORS - UL 810A 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover electrochemical capacitors for use in equipm

20、ent such as electronic products, uninterruptible power supplies, emergency lighting, engine starting, and power equipment. These energy storage capacitors, also known as “electric double layer capacitors”, ”ultracapacitors”, “double layer capacitors” or “supercapacitors” consist of either individual

21、 capacitors or multiple series and/or parallel connected capacitors with or without associated circuitry. 1.2 These requirements do not cover electrochemical capacitors for use in hazardous (Classied) locations. 2 Units of Measurement 2.1 Values stated without parentheses are the requirement. Values

22、 in parentheses are explanatory or approximate information. 3 Undated References 3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 4 Components 4.1 Except as indicated in 4.

23、2, a component of a product covered by this standard shall comply with the requirements for that component. 4.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by thi

24、s standard, or b) Is superseded by a requirement in this standard. 4.3 A component shall be used in accordance with its rating established for the intended conditions of use. 4.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are

25、intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. OCTOBER 7, 2008 ELECTROCHEMICAL CAPACITORS - UL 810A 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHO

26、UT PERMISSION FROM UL 5 Glossary 5.1 For the purpose of this standard the following denitions apply. 5.2 CAPACITOR For the purposes of this standard, a single electrochemical capacitor will be referred to as a capacitor and is a single energy storage device whose charge and discharge is not the resu

27、lt of a chemical reaction. 5.3 CAPACITOR CASING The container for an individual capacitor that serves to protect and contain its internal components and prevent injury from contact to hazardous materials. 5.4 CAPACITOR ELECTRODE The layered interior windings of a capacitor. 5.5 CAPACITOR MODULE A si

28、ngle or multiple series and/or parallel-connected, electrochemical capacitors with associated circuitry. 5.6 COMPONENT, CURRENT LIMITING Any component used to restrict the ow of electrical charge during abnormal conditions. Current-limiting components include resistors, fuses and PTC thermistor type

29、 devices. 5.7 COMPONENT, TEMPERATURE LIMITING Any component used to restrict the degree of overheating during abnormal conditions. Temperature-limiting components include thermal protectors, thermal cutoffs, and PTC thermistor type devices. 5.7A ELECTROCHEMICAL CAPACITOR An electric energy storage d

30、evice where electrical charge is stored as a result of non-Faradaic processes at one or both of the electrodes. (A subset of electrochemical capacitors referred to as an asymmetric electrochemical capacitor have non-Faradaic processes at one electrode and Faradaic processes at the other electrode.)

31、The unique highly-porous electrode increases its surface area for holding charge resulting in much larger capacitance and energy density than other types of capacitors. Electrochemical capacitors differ from common electrolytic capacitors in that they store charge at the liquid-solid interface of th

32、e electrodes when a potential is applied rather than in a solid dielectric material covering the surfaces of the electrodes. Some other common names for an electrochemical capacitor are double layer capacitor , ultra-capacitor , electrochemical double layer capacitor , super-capacitor , and EDLC. 5.

33、7A added November 1, 2012 5.8 ELECTROLYTE The medium containing ions which facilitates transfer of charge within the capacitor. 5.9 ENCLOSURE The part of the capacitor module that: a) Renders inaccessible all or any parts of the equipment that may otherwise present a risk of electric shock, or b) Re

34、tards propagation of ame initiated by electrical disturbances occurring within. 5.10 EXPLOSION A condition that occurs when the capacitor contents are forcibly expelled and the capacitor enclosure is torn or split into two or more pieces. 5.11 FAMILY (CAPACITOR) A series of capacitors from the same

35、manufacturer that are the same shape, chemistry and construction, but that differ from each other only in size and electrical ratings. NOVEMBER 1, 2012 ELECTROCHEMICAL CAPACITORS - UL 810A 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5.1

36、2 FIXED EQUIPMENT Any equipment or appliance that is intended to be hard wired to the supply circuit. 5.13 HAZARDOUS VOLTAGE Voltage greater than 60 Vdc or 45 Vrm. 5.14 INSULATED LEAD Wiring such as appliance wiring or building wire, etc., provided with thermoplastic or rubber insulation and typical

37、ly marked with the wire gauge and the temperature and voltage rating of the insulation material. 5.15 LOWER FLAMMABLE LIMIT (LFL) Minimum concentration of a ammable gas/vapor in air which ame is propagated. For example, the LFL of hydrogen is 4 percent by volume. NOVEMBER 1, 2012 ELECTROCHEMICAL CAP

38、ACITORS - UL 810A 6AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NOVEMBER 1, 2012 ELECTROCHEMICAL CAPACITORS - UL 810A 6B No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSI

39、ON FROM UL 5.16 SEPARATOR Material used to provide electronic separation (not electronically conductive) while still allowing ionic conduction between the positive and negative electrodes within the capacitor. 5.17 SHORT CIRCUIT A direct connection between positive and negative terminals of the capa

40、citor that provides a virtual zero resistance path for current ow. 5.18 STATIONARY EQUIPMENT Any equipment or appliance that is intended to be fastened in place or located in a dedicated space, and is provided with a power-supply cord for connection to the supply circuit. 5.19 TERMINAL The point of

41、electrical connection of the capacitor to the circuit. CONSTRUCTION 6 Casing/Enclosure 6.1 General 6.1.1 A capacitor shall be provided with a casing that serves to protect and contain its internal components and prevent injury from contact to hazardous materials. The capacitor casing shall be resist

42、ant to deterioration from the internal materials it is in contact with. Metallic casing materials shall comply with 6.2.2. Non-metallic casing materials shall comply with the applicable requirements outlined in 6.3. 6.1.2 A capacitor module may or may not be provided with an enclosure. 6.1.3 The enc

43、losure of a capacitor module shall prevent mechanical damage to internal capacitors and circuitry which could lead to a hazardous condition and provide protection from injury due to contact with hazardous parts. The enclosure of the capacitor module shall have the strength and rigidity necessary to

44、resist the abuses to which it is likely to be subjected without resulting in a hazardous condition due to total or partial collapse with resulting damage or displacement of parts, reduction of spacings, etc. 6.2 Metallic 6.2.1 A metal enclosure of a capacitor module shall have the strength and rigid

45、ity necessary to provide protection in accordance with 6.1.3. When determining the suitability of a metal enclosure, the applicable factors noted in 6.3.3 shall be taken into consideration. 6.2.2 A metallic casing for a capacitor shall be aluminum or other corrosion resistant material and shall prov

46、ide the protection to the internal contents of the capacitor required to comply with the Mechanical Tests of Section 18. 6.2.2 revised June 7, 2011 JUNE 7, 2011 ELECTROCHEMICAL CAPACITORS - UL 810A 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FR

47、OM UL 6.3 Nonmetallic 6.3.1 A polymeric material used as part or all of an enclosure of a capacitor module shall comply with the applicable requirements in the Standard for Polymeric Materials Use in Electrical Equipment Evaluations, UL 746C. 6.3.2 A polymeric material used as a capacitor casing sha

48、ll: a) Be classed V-2 minimum in accordance with the Standard for Tests for Flammability of Plastic Materials for Parts in Devices and Appliances, UL 94, or b) Comply with the 20 mm (3/4-inch) ame ammability test specied in the Standard for Polymeric Materials Use in Electrical Equipment Evaluations

49、, UL 746C. 6.3.3 Among the factors that shall be taken into consideration when investigating the acceptability of a nonmetallic material for a capacitor module enclosure or a capacitor casing with respect to its intended application are: a) Mechanical strength; b) Moisture-absorbent properties; c) Combustibility; d) Compatibility with electrolyte and other mediums in contact with; Note: Compliance shall be determined by the Practice A Immersion Test in Stand