UL 69-2009 UL Standard for Safety Electric-Fence Controllers (Tenth Edition Reprint with Revisions Through and Including April 20 2018)《电网控制器》.pdf

《UL 69-2009 UL Standard for Safety Electric-Fence Controllers (Tenth Edition Reprint with Revisions Through and Including April 20 2018)《电网控制器》.pdf》由会员分享，可在线阅读，更多相关《UL 69-2009 UL Standard for Safety Electric-Fence Controllers (Tenth Edition Reprint with Revisions Through and Including April 20 2018)《电网控制器》.pdf（80页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 69 Electric-Fence ControllersUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPR

2、ODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Electric-Fence Controllers, UL 69 Tenth Edition, Dated June 30, 2009 Summary of Topics The revisions dated December 4, 2013 have been issued for the Standard for Electric-Fence Controllers, UL 69, to incorporate the propo

3、sals dated May 24, 2013. These proposals include the following: Requirements for direct plug-in fence controllers. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical

4、 line in the margin and are followed by an effective date note indicating the date of publication or the date on which the changed requirement becomes effective. The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated May 24, 2013. All rights reserved.

5、 No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implie

6、d, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use

7、 of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versi

8、ons of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the p

9、urchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have be

10、en revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. DECEMBER 4, 2013 UL 69 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 4, 2013 UL 69 tr2 No Te

11、xt on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 30, 2009 (Title Page Reprinted: December 4, 2013) 1 UL 69 Standard for Electric-Fence Controllers First Edition September, 1939 Second Edition June, 1948 Third Edition May,

12、1973 Fourth Edition October, 1976 Fifth Edition September, 1980 Sixth Edition January, 1985 Seventh Edition March, 1987 Eighth Edition May, 1993 Ninth Edition June, 2003 Tenth Edition June 30, 2009 This ANSI/UL Standard for Safety consists of the Tenth Edition including revisions through December 4,

13、 2013. The most recent designation of ANSI/UL 69 as an American National Standard (ANSI) occurred on December 4, 2013. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the St

14、andard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way

15、. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2013 UNDERWRITERS LABORATORIES INC. ANSI/UL 69-2013UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISS

16、ION FROM UL DECEMBER 4, 2013 ELECTRIC-FENCE CONTROLLERS - UL 69 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .6 2 Components 6 3 General 6A 3.1 Units of measurement .6A 3.2 Undated refer

17、ences .6A 4 Glossary 6A CONSTRUCTION 5 General 6B 6 Enclosure .6B 6.1 General 6B 6.2 Doors and covers .9 6.3 Thickness 10 6.4 Openings .10 7 Mounting 11 8 Mechanical Assembly 11 9 Protection Against Corrosion 12 10 Supply Connections .12 10.1 General .12 10.2 Permanently mounted controllers .13 10.3

18、 Portable controllers .14 10.4 Direct plug-in controllers .16A 11 Current-Carrying Parts 17 12 Accessible Parts 17 13 Internal Wiring 18 13.1 General .18 13.2 Splices and connections 19 14 Insulating Material 19 15 Grounding .20 16 Motors .21 17 Protective Devices 21 17.1 Overload protection .21 17.

19、2 Overcurrent protection 22 17.3 Overvoltage suppressors 22 17.4 Transient voltage surge suppressors 22 17.5 Software 22 18 Transformers .22A 19 Spacings 23 20 Polymeric Materials .24 PERFORMANCE 21 General 25 22 Output Characteristics Test 26 22.1 General .26 22.2 Operating position 28 22.3 Voltage

20、 range 28 DECEMBER 4, 2013 ELECTRIC-FENCE CONTROLLERS - UL 69 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 23 Abnormal Operation Test 29 23.1 Pilot lights .29 23.2 Components .29 23.3 Live parts .32 24 Leakage Current Test .32 25 Leakage

21、-Current Test Following Humidity Conditioning 34 26 Temperature Test .34 27 Dielectric Voltage-Withstand Test .35 28 Humidity and Water-Spray Test 36 28.1 Humidity 36 28.2 Water-spray .36 29 Hosedown Test .39 30 Impact Test 40 31 Burnout Test .40 32 Ignition Tests .41 32.1 General .41 32.2 Cloth ign

22、ition .41 32.3 Surgical cotton ignition 41 33 Endurance Test 42 34 Strain-Relief Test .43 MANUFACTURING AND PRODUCTION TESTS 35 Dielectric Voltage-Withstand Test .43 36 Output Characteristics Tests 44A 36A Direct Plug-In Tests 44A 36A.1 General 44A 36A.2 Blade secureness test 44A 36A.3 Security of i

23、nput contacts test 44B 36A.4 Security of output connectors test .44B 36A.5 Rod pressure .44C 36A.6 Resistance to crushing .44C RATING 37 General 44C MARKING 38 General 44C 39 Cautionary and Warning Markings .44D 39.1 General 44D 39.2 Servicing 47 39.3 Fuse replacement 48 39.4 Grounding .48 40 Instal

24、lation and Operating Instructions .49 DECEMBER 4, 2013 ELECTRIC-FENCE CONTROLLERS - UL 69 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SUPPLEMENT SA - ALTERNATIVE EVALUATION PROGRAM FOR ELECTRIC-FENCE CONTROLLERS INTRODUCTION SA1 Scope S

25、A1 DECEMBER 4, 2013 ELECTRIC-FENCE CONTROLLERS - UL 69 4AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 4, 2013 ELECTRIC-FENCE CONTROLLERS - UL 69 4B No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTI

26、ON OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION SA2 Grounding SA1 SA3 Protective Devices .SA1 SA3.1 Overload protection .SA1 SA4 Isolation SA1 PERFORMANCE SA5 Output Characteristics Test .SA2 SA6 Temperature Test SA4 SA7 Voltage Range SA4 SA8 Abnormal Operation Test .SA4 SA8.1 Components

27、SA4 MANUFACTURING AND PRODUCTION TESTS SA9 Output Characteristics Test .SA4 APPENDIX A Standards for ComponentsA1 JUNE 30, 2009 ELECTRIC-FENCE CONTROLLERS - UL 69 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 Thes

28、e requirements cover electric-fence controllers to be employed on lighting or line circuits in accordance with the National Electrical Code, NFPA 70. 1.2 These requirements cover electric-fence controllers used only for the control of animals. 1.3 These requirements cover portable and permanently mo

29、unted electric-fence controllers with peak-discharge or sinusoidal-discharge output for indoor or outdoor use, including battery-operated controllers intended to operate from battery circuits of 42.4 V or less, line-operated controllers intended to operate from circuits of 125 V or less, combination

30、 controllers intended to operate from either a battery or a line circuit, and photovoltaic module battery operated controllers. 1.4 These requirements do not cover electric-fence controllers for the continuous (uninterrupted) current type or intermediate equipment, such as a converter, a rectier, or

31、 the like, that is sometimes used between the primary source of supply and an electric-fence controller and that is investigated only as part of a complete controller. 1.5 These requirements do not cover electric-fence controllers for use with electried security fences. 1.5 added January 7, 2013 2 C

32、omponents 2.1 Except as indicated in 2.2, a component of a product covered by this standard shall comply with the requirements for that component. See Appendix A for a list of standards covering components generally used in the products covered by this standard. 2.2 A component need not comply with

33、a specic requirement that: a) Involves a feature or characteristic not needed in the application of the component in the product covered by this standard, or b) Is superceded by a requirement in this standard. 2.3 A component shall be used in accordance with its recognized rating established for the

34、 intended conditions of use. 2.4 Specic components are recognized as being incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used o

35、nly under those specic conditions for which they have been recognized. JANUARY 7, 2013 ELECTRIC-FENCE CONTROLLERS - UL 69 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3 General 3.1 Units of measurement 3.1.1 If a value for measurement is

36、 followed by another value in other units in parentheses, the second value may be only approximate. The rst stated value is the requirement. 3.2 Undated references 3.2.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to th

37、e latest edition of that code or standard. 4 Glossary 4.1 For the purpose of this standard the following denitions apply. 4.2 CONTINUOUS CURRENT OUTPUT Output current which has a steady-state peak of 7.0 mA or more. 4.3 CURRENT PULSE The current which ows during the time period in which 95 percent o

38、f the output energy of a single fence controller output waveform has been transferred to the load resistor. 4.3.1 DIRECT PLUG-IN CONTROLLER An electric fence controller for indoor use only with a single output which employs a blade assembly on the enclosure for connection to the branch circuit. The

39、controller may be provided with output wiring or wire binding screws intended for connection to solid wire. Not considered a direct plug-in power supply that is detachable from the electric fence controller. 4.3.1 added December 4, 2013 4.4 ELECTRICAL BREAKDOWN Occurs when a discharge bridges the in

40、sulation under test, reducing the voltage between the electrodes to zero or nearly zero. 4.5 EQUIPMENT GROUNDING MEANS A lead or terminal, provided in the splice compartment of a permanently mounted fence controller, that is intended for connection to the branch circuit (supply) grounding conductor;

41、 or the grounding pin of an attachment plug of a 3-wire power supply cord, provided on a portable fence controller, that is intended for connection to the branch circuit (supply) grounding conductor. 4.6 FENCE TERMINAL The output terminal that is not intended to be connected to earth ground. 4.7 LEA

42、KAGE CURRENT Any current that may be conveyed from accessible parts, other than the fence output terminals, to ground or to other accessible parts. 4.8 OUTPUT GROUND TERMINAL The output terminal that is intended to be connected to the fence ground rod. 4.9 PEAK-DISCHARGE OUTPUT Output current pulses

43、 that are unidirectional single impulses. 4.10 PERMANENTLY CONNECTED CONTROLLERS Connected to branch circuit wiring by a means other than a cord and plug, such as by using conduit. 4.11 PERMANENTLY MOUNTED CONTROLLERS Secured to a mounting surface by a means that requires the use of a tool for remov

44、al. DECEMBER 4, 2013 ELECTRIC-FENCE CONTROLLERS - UL 69 6AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4.12 PORTABLE CONTROLLER A cord connected controller that is mounted by means not requiring a tool for removal and not intended for per

45、manent mounting. 4.13 PULSE SEGMENT A part of a current pulse that is between any two points in time within the duration of the current pulse. 4.14 SECONDARY CIRCUITS Those circuits supplied from transformer output windings that are electrically separated from the input windings. 4.15 SINUSOIDAL-DIS

46、CHARGE OUTPUT Output current pulses that are oscillatory current waveforms. 4.16 SUPPLEMENTARY (PROTECTING) INSULATION An independent insulation provided in addition to basic insulation to protect against electric shock in case of mechanical rupture or electrical breakdown of the basic insulation. A

47、n enclosure of insulating material may form a part or the whole of the supplementary insulation. 4.17 SUPPLY CIRCUIT The branch circuit supplying electrical energy to the fence controller. CONSTRUCTION 5 General 5.1 A fence controller shall employ materials that are acceptable for the use. 5.2 An en

48、closure, an opening, a frame, a guard, a knob, a handle, or the like shall not be sufficiently sharp to constitute a risk of injury in normal maintenance or use. 6 Enclosure 6.1 General 6.1.1 A fence controller shall be provided with an enclosure that, except for the fence terminals, will enclose al

49、l uninsulated live parts. The enclosure shall be constructed of metal or polymeric material that complies with the requirements for Polymeric Materials, Section 20. 6.1.2 The enclosure housing the timing and output mechanism shall be dust and water-resistant as determined by the Humidity and Water-Spray Test, Section 28, and the Hosedown Test, Section 29. 6.1.3 The enclosure shall be formed so that it will have the strength and rigidity necessary to resist the abuses to