UL 687-2011 UL Standard for Safety Burglary-Resistant Safes (Fifteenth Edition Reprint with revisions through and including November 25 2015)《防盗保险柜》.pdf

《UL 687-2011 UL Standard for Safety Burglary-Resistant Safes (Fifteenth Edition Reprint with revisions through and including November 25 2015)《防盗保险柜》.pdf》由会员分享，可在线阅读，更多相关《UL 687-2011 UL Standard for Safety Burglary-Resistant Safes (Fifteenth Edition Reprint with revisions through and including November 25 2015)《防盗保险柜》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 687 Burglary-Resistant SafesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRO

2、DUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Burglary-Resistant Safes, UL 687 Fifteenth Edition, Dated July 19, 2011 Summary of Topics This revision of ANSI/UL 687 is being issued to reect the reaffirmation of the ANSI approval of the standard. No technical changes h

3、ave been made to the document. The revisions are substantially in accordance with Proposal(s) on this subject dated September 25, 2015. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. All rights reserved. No part

4、of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, includ

5、ing but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or th

6、e inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of UL

7、s Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers

8、 computer system. NOVEMBER 25, 2015 UL 687 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NOVEMBER 25, 2015 UL 687 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION

9、 FROM UL JULY 19, 2011 (Title Page Reprinted: November 25, 2015) 1 UL 687 Standard for Burglary-Resistant Safes First Edition June, 1938 Second Edition June, 1943 Third Edition January, 1953 Fourth Edition May, 1955 Fifth Edition June, 1960 Sixth Edition August, 1967 Seventh Edition July, 1972 Eight

10、h Edition December, 1977 Ninth Edition January, 1982 Tenth Edition September, 1987 Eleventh Edition December, 1991 Twelfth Edition May, 1995 Thirteenth Edition August, 2000 Fourteenth Edition October, 2005 Fifteenth Edition July 19, 2011 This ANSI/UL Standard for Safety consists of the Fifteenth Edi

11、tion including revisions through November 25, 2015. The most recent designation of ANSI/UL 687 as a Reaffirmed American National Standard (ANS) occurred on November 25, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. T

12、he Department of Defense (DoD) has adopted UL 687 on June 10, 1976. The publication of revised pages or a new edition of this Standard will not invalidate the DoD adoption. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitt

13、ed via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights rega

14、rding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 687-2011 (R2015)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 19, 2011 BURGLARY-RESISTANT SAFES - UL 687 2

15、 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Components 6 2.2 Units of measurement .6 2.3 Undated references .6 3 Glossary 6 CONSTRUCTION 4 General 8 4.1 Compliance 8 4

16、.2 Locks .8 4.3 Corrosion protection 9 5 Class TL-15 and Deposit Safes 9 5.1 General 9 5.2 Locks 10 6 Class TL-30 10 6.1 General .10 6.2 Locks 11 7 Class TL-15X6 11 7.1 General .11 7.2 Locks 11 8 Class TL-30X6 12 8.1 General .12 8.2 Locks 12 9 Class TRTL-30 12 9.1 General .12 9.2 Locks 13 10 Classes

17、 TRTL-15X6, TRTL-30X6, and TRTL-60X6 .14 10.1 General .14 10.2 Locks 14 11 Class TXTL-60X6 .14 PERFORMANCE 12 General 14 12.1 Compliance .14 12.2 Samples .15 12.3 Combination drifting and drilling .15 12.4 Drilling lock mechanism 15 12.5 Handle forcing 15 12.6 Door sledging and wedging .16 12.7 Dril

18、ling of an opening 16 13 Net Working Time .16 14 Attack Resistance .16 15 Class TL-15 17 15.1 Performance test 17 15.2 Test equipment .18 JULY 19, 2011 BURGLARY-RESISTANT SAFES - UL 687 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 16 Cla

19、ss Deposit Safes .18 16.1 Performance test 18 16.2 Test equipment .19 17 Class TL-30 19 17.1 Performance test 19 17.2 Test equipment .19 18 Class TL-15X6 .20 18.1 Performance test 20 18.2 Test equipment .20 19 Class TL-30X6 .20 19.1 Performance test 20 19.2 Test equipment .20 20 Class TRTL-30 .21 20

20、.1 Performance test 21 20.2 Test equipment .21 21 Class TRTL-15X6 .21 21.1 Performance test 21 21.2 Test equipment .22 22 Class TRTL-30X6 .22 22.1 Performance test 22 22.2 Test equipment .22 23 Class TRTL-60X6 .23 23.1 Performance test 23 23.2 Test equipment .23 24 Class TXTL-60X6 .24 24.1 Performan

21、ce test 24 24.2 Test equipment .24 MARKING 25 General 25 JULY 19, 2011 BURGLARY-RESISTANT SAFES - UL 687 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover combination locked burglary-resistant

22、 safes classied as follows: a) Test attack against the door and front face: 1) Tool-Resistant Safe Class TL-15 2) Tool-Resistant Safe Deposit Safe 3) Tool-Resistant Safe Class TL-30 4) Torch- and Tool-Resistant Safe Class TRTL-30 b) Test attack against the door and body: 1) Tool-Resistant Safe Class

23、 TL-15X6 2) Tool-Resistant Safe Class TL-30X6 3) Torch- and Tool-Resistant Safe Class TRTL-15X6 4) Torch- and Tool-Resistant Safe Class TRTL-30X6 5) Torch- and Tool-Resistant Safe Class TRTL-60X6 6) Torch-, Explosive-, and Tool-Resistant Safe Class TXTL-60X6 1.2 These requirements do not cover night

24、 depositories intended to receive deposits from outside a building into a receiving safe inside a building. Such requirements are in the Standard for Night Depositories, UL 771. 1.3 A safe classied as TL-15, TL-30, TL-15X6, or TL-30X6 may be constructed with an opening in the body for connection to

25、the chute of a night depository. A safe classied as TL-15 or TL-30 that has a body constructed of solid metal may be marked to provide for an opening to be cut into the body in the eld for connection to the chute of a night depository. JULY 19, 2011 BURGLARY-RESISTANT SAFES - UL 687 5UL COPYRIGHTED

26、MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.1.2 A component is not required to compl

27、y with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the

28、 intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those sp

29、ecic conditions. 2.2 Units of measurement 2.2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be in

30、terpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 For the purpose of this standard the following denitions apply. 3.2 ABRASIVE CUTTING WHEEL Metal or stone cutting abrasive wheel, maximum 8 inches (203 mm) diameter, and maximum 1/8 inch (3.2 mm) thick. Driven by e

31、lectrically-powered disk grinder rated 10 20 A, 115 120 V (5 10 A, 230 240 V), 8000 rpm maximum. 3.3 COMMON HAND TOOLS Common hand tools include: chisels, punches, wrenches, screwdrivers, pliers, hammers and sledges not exceeding the 8-pound (3.6-kg) size, and pry bars and ripping tools not exceedin

32、g 5 feet (1.52 m) in length. 3.4 CUTTING TORCH Oxygen-acetylene fueled cutting torch, 180 degrees (straight) or 90 degrees, maximum No. 18 tip with six preheat holes 0.055 inch (1.4 mm) diameter each, and one oxygen hole 3/16 inch (4.8 mm) diameter. A smaller tip may be used. 3.5 DEPOSIT BAG A bag c

33、onstructed of canvas, reinforced plastic, or the like, that is provided with a closing mechanism, such as a zipper. 3.6 DEPOSIT ENVELOPE A No. 10 or larger size business envelope. 3.7 ENTRY : JULY 19, 2011 BURGLARY-RESISTANT SAFES - UL 687 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUC

34、TION OR DISTRIBUTION WITHOUT PERMISSION FROM UL a) SAFES CLASSED TL-15 AND TL-30 Opening the door or making a 6 square inch (38.7 cm 2 ) opening entirely through the door or front face. b) SAFES CLASSED DEPOSIT SAFES Opening the door or making a 6 square inch opening entirely through the door, front

35、 face, or deposit mechanism; removing three deposit envelopes or one deposit bag through the deposit mechanism; or trapping deposit envelopes or bags. c) SAFES CLASSED TL-15X6 AND TL-30X6 Opening the door or making a 6 square inch (38.7 cm 2 ) opening entirely through the door or body. d) SAFES CLAS

36、SED TRTL-30 Opening the door or making a 2 square inch (12.9 cm 2 ) opening entirely through the door or front face. e) SAFES CLASSED TRTL-15X6, TRTL-30X6, TRTL-60X6, AND TXTL-60X6 Opening the door or making a 2 square inch opening entirely through the door or body. 3.8 FISHING Introducing through t

37、he deposit mechanism, shing tools that may be manipulated so as to grasp the deposit envelope, or bag, and then withdraw it. 3.9 FISHING AND TRAPPING TOOLS Cardboard, plastic sheet, sh hooks, exible spring shaft pickup ngers, lines, shim stock, and the like. 3.10 GRINDING POINT Various shaped grindi

38、ng points (cone, cylinder, disk, and the like) driven by electrically-powered grinder rated41 2A ,115 120 V (26A ,2 3 02 4 0V ) ,a tspeeds of 14,000 to 21,000 rpm. 3.11 IMPACT TOOLS Includes portable electric impact hammers and hammer drills, not exceeding the 1 inch (25.4 mm) size and rated 10 20 A

39、, 115 120 V (5 10 A, 230 240 V). 3.12 PICKING TOOLS Picking tools include common or standard patterns that are not designed for use against a special make of safe. 3.13 PORTABLE ELECTRIC DRILL Electric hand drills not exceeding the 1/2 inch (12.7 mm) size and rated51 5A ,1 1 51 2 0V(2.5 7.5 A, 230 2

40、40 V). 3.14 PRESSURE APPLYING DEVICES Includes portable drill presses, portable drilling jigs, or other types of drill holding mechanisms. 3.15 SAW, CIRCULAR Metal or stone cutting, maximum 8-inch (203-mm) diameter circular blade with high-speed steel or carbide-tipped cutting teeth. Driven by elect

41、rically-powered circular saw rated 10 20 A, 115 120 V (5 10 A, 230 240 V), 5000 rpm maximum. 3.16 SAW, HOLE Cylinder-shaped saws used to cut holes. Maximum 3-inches (76-mm) diameter with high-speed steel or carbide-tipped cutting teeth. Used with a 1/2-inch (12.7-mm) electric drill, dened in 3.13. 3

42、.17 SAW, RECIPROCATING Hand-held reciprocating saw with high-speed or carbide-tipped cutting teeth. Rated 10 20 A, 115 120 V (5 10 A, 230 240 V). Length of blade may be the maximum length commercially available. 3.18 SIX-SQUARE-INCH OPENING This type of opening is dened as: JULY 19, 2011 BURGLARY-RE

43、SISTANT SAFES - UL 687 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL a) A rectangular-shaped opening 6 square inches (39 cm 2 ) in area, with the smallest dimension 1.5 inches (38 mm) or greater; b) A circular opening 2.76 inches (70 mm)

44、in diameter; or c) A triangular opening with at least a 2-inch (51-mm) dimension from the base to the peak. 3.19 TESTING PARTY A testing party shall consist of two experienced operators under the supervision of a test director. The testing party shall be familiar with the construction of the safe be

45、ing tested. 3.20 TRAPPING The use of trapping tools that may be introduced into the deposit mechanism in such a manner as to avoid detection by a depositor, in order to prevent the deposit from reaching the safe. The deposit can then be withdrawn after the depositor has left. 3.21 TWO-SQUARE-INCH OP

46、ENING This type of opening is dened as: a) A rectangular-shaped opening 2 square inches (12.9 cm 2 ) in area, with the smallest dimension 1 inch (25.4 mm) or greater; b) A circular opening 1.6 inches (40.6 mm) in diameter; or c) A triangular opening with at least a 1-inch (25.4-mm) dimension from th

47、e base to the peak. CONSTRUCTION 4 General 4.1 Compliance 4.1.1 In addition to specic requirements for each class, all safes shall comply with 4.2.1 and 4.3.1. 4.2 Locks 4.2.1 A combination lock shall be provided on all safes. JULY 19, 2011 BURGLARY-RESISTANT SAFES - UL 687 8UL COPYRIGHTED MATERIAL

48、NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4.3 Corrosion protection 4.3.1 All iron and steel parts shall be painted, plated, or the equivalent to protect against corrosion. 5 Class TL-15 and Deposit Safes 5.1 General 5.1.1 The safe shall weigh at least 750 pou

49、nds (340 kg), or shall be equipped with anchors and instructions for anchoring the safe in a larger safe, in concrete blocks, or to the premises in which the safe is to be located. 5.1.2 The metal in the body shall be: a) Equivalent to solid open-hearth steel at least 1 inch (25.4 mm) thick having an ultimate tensile strength of 50,000 psi (345 MPa); b) Either cast or fabricated; and