UL 62-2018 UL Standard for Safety Flexible Cords and Cables (Twentieth Edition).pdf

《UL 62-2018 UL Standard for Safety Flexible Cords and Cables (Twentieth Edition).pdf》由会员分享，可在线阅读，更多相关《UL 62-2018 UL Standard for Safety Flexible Cords and Cables (Twentieth Edition).pdf（159页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 62 Flexible Cords and Cables STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZ

2、ED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Flexible Cords and Cables, UL 62 Twentieth Edition, Dated July 6, 2018 Summary of Topics This new edition of ANSI/UL 62 has been published to update the ANSI approval of the standard and includes: Revis

3、ed reference publications. Removal of specic material requirements for tape or yarn used as a separator. Claried construction requirements for range and dryer cords and added mm 2 size designations. Claried substitutability of materials of higher temperature ratings. Changed % to percent and better

4、dened how diameter (D) under braid is to be used and measured. Added a requirement for testing of bare copper wire shields with thermoset insulations. Claried the required ame test requirements for SPT cords used in Mexico. Added HSJW and HPNW to permit use of heater cords exposed to sunlight and wa

5、ter|. Revised wording to clarify the requirements for insulations used in duplex units of elevator cables. Added NISP-1, NISP-2, NISPE-1, NISPE-2, NISPT-1, NISPT-2 to clarify that these types are not required to be subjected to the Tightness of Insulation test. Clarifed the AC Leakage Current Test f

6、or Low Leakage Cord. Claried oil resistant types that can have an O in the type designation and those types that are required to be oil resistant, but are not permitted to have an O in the type designation. Added a requirement for caution marking on single conductor CXWT c . Added new types CXTW-S a

7、nd CXTW-IS that can be shown to have the equivalent strength to the breaking strength of a 2-conductor, twisted 22 AWG CXTW (UL 588, 13.2.4), or to the breaking strength of a single conductor CXTW twisted with a supporting rope (UL 588, 81A.2). Added the -X suffix for Type CXTW in sizes smaller than

8、 22 AWG that are equivalent in breaking strength to a 22 AWG, Added Types LXT and LXTW used in decorative lighting products, and added -X suffix for constructions that are equivalent in breaking strength to 22 AWG. Added testing and marking requirements for cords incorporating the overall braid. Add

9、ed the missing Spark Test voltage in Table 46. JULY 6, 2018 UL 62 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Added 20 AWG DPT and DPTW types. Added grounding conductor size for cables containing 9 AWG circuit conductors. Added 1000 V

10、 electric vehicle cable. Claried the denition of Neutral Conductor. Added thermoplastic oil resistant compound like an SVTO as an optional jacket for elevator cables. Added Annex D to provide a list of cord types by country. Added a note to Table 22 for single conductor CXWT used in two conductor CX

11、WT twisted lighting strings. Revised Table 20 to allow SPT-1W and SPT-2W for use in Canada and Mexico. Added applicable tests for conductors containing brous strength members. Added harmonized type designations for Flexible Cords and Cables and Electric Vehicle Cables using TPE insulation and jacket

12、. Added the abbreviation w/thrd to shorten the required marking for those products containing a thread in the conductor. Revised the Cold Impact Test temperature required on all electric vehicle cables. Added Type YXTW for use in year-round lighting strings. Revised requirements for data and signal

13、conductors used in Electric Vehicle Cables. Editorial changes. The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated August 4, 2017. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in a

14、ny form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpo

15、se. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been

16、 advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against

17、 any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic JULY 6, 2018 UL 62 tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERM

18、ISSION FROM UL Standard on the purchasers computer system. JULY 6, 2018 UL 62 tr3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 6, 2018 UL 62 tr4 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DI

19、STRIBUTION WITHOUT PERMISSION FROM UL Association of Standardization and Certication NMX-J-436-ANCE-2018 Sixth Edition CSA Group CAN/CSA C22.2 No. 49-18 Fifteenth Edition Underwriters Laboratories Inc. UL 62 Twentieth Edition Flexible Cords and Cables July 6, 2018 ANSI/UL 62-2018UL COPYRIGHTED MATER

20、IAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Association of Standardization and Certication (ANCE), the Canadian Standards Association (operating as “CSA Group”), and Underwriters Laboratories

21、Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to ANCE, CSA Group, or UL at anytime. Revisions to this standard will be made only after processing according to the standards development procedures of ANCE, CSA Group, and UL. CSA Group and UL will issue re

22、visions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ANCE will incorporate the same revisions into a new edition of the standard bearing the same date of issue as the CSA Group and UL pages. Copyright 2018 ANCE Rights reserved in favor of ANC

23、E. ISBN 978-1-4883-0823-9 2018 Canadian Standards Association All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subject to review within ve years from the date of publication, and suggestions for

24、its improvement will be referred to the appropriate committee. To submit a proposal for change to CSA Standards, please send the following information to inquirescsa.ca and include Proposal for change in the subject line: Standard designation (number); relevant clause, table and/or gure number; word

25、ing of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Groups Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2018 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by

26、 UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the Twentieth Edition. The

27、 most recent designation of ANSI/UL 62 as an American National Standard (ANSI) occurred on July 6, 2018. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page (front and back), or the Preface. TheDepartmentofDefense(DoD)hasadoptedUL62onNovember6,1987.Thepublicat

28、ionofrevised pages or a new edition of this Standard will not invalidate the DoD adoption. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development Syste

29、m (CSDS) at https:/. To purchase UL Standards, visit ULs Standards Sales Site at http:/ HowToOrder.aspx or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS PREFACE 4 1 Scope .6 1.1 General .6 1.2 Product

30、s included 6 1.3 National differences.6 2 Reference publications 7 3 Denitions and units of measurement .9 3.1 Denitions .9 3.2 Units of measurement11 4 Construction requirements 11 4.1 General construction requirements 11 4.2 Thermoset-insulated cords (including range and dryer cords and special-us

31、e cords C u and PD u ).21 4.3 Thermoplastic-insulated cords (including decorative and range and dryer cords) 24 4.4 Heater cords HSJOO, HSJOOW, HSJO, HSJW c,u , HSJOW, HSJ, HPN, HPNW c,u , and HPD m,u .29 4.5 Tinsel cords (TST, TPT, shaver cord u ).31 4.6 Elevator travelling cables Types E, EO, ETT,

32、 and ETP .33 4.7 Hoistway cables .38 4.8 Electric vehicle cables .41 5 Performance and test requirements 43 5.1 Physical properties 43 5.2 Electrical properties57 5.3 Tests for hoistway cables.61 6 Marking.63 6.1 General 63 6.2 Product marking.63 6.3 Optional markings .66 6.4 Package marking 66 6.5

33、Hoistway cables .68 6.6 Recreational vehicle cord.69 6.7 Mobile home and recreational vehicle cord .69 Tables 71 Figures 131 Annex A (normative) Calculation method for brous braids Annex B (informative) Insulated conductor identication Annex C (informative) French and Spanish translations of caution

34、 markings Annex D (informative) Products recognized by their respective countries JULY 6, 2018 NMX-J-436-ANCE-2018 CAN/CSA C22.2 NO. 49-18 UL 62 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL PREFACE This is the harmonized ANCE, CSA Group,

35、 and UL standard for exible cords and cables. It is the sixth edition of NMX-J-436-ANCE, the fteenth edition of CAN/CSA-C22.2 No. 49, and the twentieth edition of UL 62. This edition of CAN/CSA C22.2 No. 49 supersedes the previous edition(s) published in 2014, 2010, 2006, 1998, 1992, 1989, 1988, 198

36、1, 1973, 1962, 1960, 1956, 1941, and 1937. This edition of UL 62 supersedes the previous edition published in 2014. This harmonized standard was prepared by the Association of Standardization and Certication (ANCE), CSA Group, and Underwriters Laboratories Inc. (UL). The efforts and support of the T

37、echnical Harmonization Subcommittee, Flex Cords, THSC 20, of the Council on the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA) are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the stand

38、ard. The present Mexican standard was developed by the CT 20 Conductores from the Comite de Normalizacion de la Asociacion de Normalizacion y Certicacion, A.C., CONANCE, with the collaboration of the wire and cables manufacturers and users. This standard was reviewed by the CSA Integrated Committee

39、on Flexible Cords/Equipment and Appliance Wires and Cables, under the jurisdiction of the CSA Technical Committee on Wiring Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been d

40、eveloped in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Applicatio

41、n of Standard Where reference is made to a specic number of samples to be tested, the specied number is to be considered a minimum quantity. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the user

42、s of the standard to judge its suitability for their particular purpose. Level of Harmonization This standard uses the IEC format but is not based on, nor is it to be considered equivalent to, an IEC standard. This standard is published as an equivalent standard for ANCE, CSA Group, and UL. An equiv

43、alent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for codes and governmental regulations as well as those recognized as being in accordance with NAFTA Article 905, for example, because of fundamental climat

44、ic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country considers appropriate. Presentation is word for word except for editorial changes. JULY 6, 2018 NMX-J-436-ANCE-2018 CAN/CSA C22.2 NO. 49-18 UL 62 4UL COPYRIGHTED MATERIAL NO

45、T AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Reasons for Differences From IEC This standard provides requirements for insulated cords and cables in accordance with the codes of Canada, Mexico, and the United States. At present there is no IEC standard for cords an

46、d cables for use in accordance with these codes. Therefore, this standard does not employ any IEC standard for base requirements. Interpretations The interpretation by the standards development organization of an identical or equivalent standard is based on the literal text to determine compliance w

47、ith the standard in accordance with the procedural rulesofthestandardsdevelopmentorganization.Ifmorethanoneinterpretationoftheliteraltexthasbeen identied, a revision is to be proposed as soon as possible to each of the standards development organizations to more accurately reect the intent. JULY 6,

48、2018 NMX-J-436-ANCE-2018 CAN/CSA C22.2 NO. 49-18 UL 62 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1 Scope 1.1 General This standard species the requirements for exible cords, elevator cables, and hoistway cables rated 600 V maximum and

49、 electric vehicle cables rated 1000 V maximum and intended for use in accordance with CAN/CSA C22.1, Canadian Electrical Code, Part I, in Canada, NOM-001-SEDE, La Norma de Instalaciones Electricas, in Mexico, and NFPA 70, National Electrical Code (NEC), in the United States. 1.2 Products included This standard covers the following products: a) Service cords; b) Elevator cables; c) Hoistway cables; d) Heater cords; e) Range and dryer cords; f)