UL 61496-1 (ND)-2002 National Differences For UL 61496-1 Standard for Electro-Sensitive Protective Equipment Part 1 General Requirements and Tests (First Edition Reprint with revis.pdf

《UL 61496-1 (ND)-2002 National Differences For UL 61496-1 Standard for Electro-Sensitive Protective Equipment Part 1 General Requirements and Tests (First Edition Reprint with revis.pdf》由会员分享，可在线阅读，更多相关《UL 61496-1 (ND)-2002 National Differences For UL 61496-1 Standard for Electro-Sensitive Protective Equipment Part 1 General Requirements and Tests (First Edition Reprint with revis.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 61496-1Standard for Electro-Sensitive Protective Equipment, Part 1: General Requirements and TestsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDIST

2、RIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 61496-1Standard for Electro-Sensitive Protective Equipment, Part 1: General Requirements and TestsEdition: 1Edition Date: January 29, 2002This revision to UL 61496-1 is being issued to reaffirm the ANSI approval. No technical changeshave

3、been made to the document.This document provides a single listing of the National Differences included in the UL adoption ofthe corresponding IEC standard.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electro

4、nic, mechanical photocopying, recording, or otherwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, either expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will

5、UL be liable for any special, incidental, consequential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof

6、the possibility of such damage. In no event shall ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any

7、loss, expense, liability, damage, claim, or judgment (including reasonableattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.Copyright 2011 Underwriters Laboratories Inc.SEPTEMBER 20, 2011NATIONAL DIFFER

8、ENCES FOR UL UL 61496-12UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Differences included in the UL adoptionof the corresponding IEC standard.In its IEC-based standard

9、s, UL uses the notations indicated below to identify national difference type, andthese types are additionally noted in this document. The standard may not use all types of thesedeviations.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich woul

10、d compromise safety for U.S. consumers and users of products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These ar

11、e deviations based on the component standards and will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or corrections.DR - These are deviations based on the national regulatory requirements.Each n

12、ational difference contains a description of what the national difference entails. Typically one of thefollowing words is used to explain how the text of the national difference is to be applied to the base IECtext:Addition / Add - An addition entails adding a complete new numbered clause, subclause

13、, table,figure, or annex. Addition is not meant to include adding select words to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause,table, figure, or annex without any replacement text.Modification / Modify - A modification is an alter

14、ing of the existing base IEC text such as theaddition, replacement or deletion of certain words or the replacement of an entire clause,subclause, table, figure, or annex of the base IEC text.SEPTEMBER 20, 2011 NATIONAL DIFFERENCES FOR UL UL 61496-1 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

15、 REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences2.1DV DC Deletion:Delete the reference to IEC 60050(191).2.2DV DC Deletion:Delete the reference to IEC 60204-1.2.3DV DC Deletion:Delete the reference to IEC 60249-2.2.4DV DC Deletion:Delete the reference to IEC 60439-1.2.5DV

16、DC Deletion:Delete the reference to IEC 60445.2.6DV DC Deletion:Delete the reference to IEC 60447.2.7DV DC Deletion:Delete the reference to IEC 60664-1.2.8DV DC Deletion:Delete the reference to IEC 60742.2.9DV DC Deletion:Delete the reference to IEC 60947-5-1.2.10DV DC Deletion:Delete the reference

17、to IEC 61310-1.2.11DV DC Deletion:Delete the reference to ISO/TR 12100-1.2.12DV DC Deletion:Delete the reference to ISO/TR 12100-2.SEPTEMBER 20, 2011NATIONAL DIFFERENCES FOR UL UL 61496-14UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL2.13DV

18、DC Addition:Add the following references:2.13DV.1 UL 508Industrial Control Equipment2.13DV.2 UL 796Printed-Wiring Boards2.13DV.3 UL 840Insulation Coordination Including Clearances and Creepage Distances for ElectricalEquipment2.13DV.4 NFPA 79:1997,Electrical Standard for Industrial Machinery (Nation

19、al Fire Codes, Volume 3)3.7DV D2 Deletion:Delete the reference to IEV 191-04-01.3.23DV D2 Deletion:Delete the reference to ISO/TR 12100-1, annex A.4.2.1DV D2 Replacement:Replace the last two paragraphs of 4.2.1 with the following:4.2.1DV.1 Any a.c. supplied ESPE or any type 4 d.c. supplied ESPE shal

20、l be provided with itsown dedicated means of isolation from the supply source either by the use of an isolatingtransformer or by an equivalent means of isolation.4.2.1DV.2 When the ESPE incorporates a battery and is capable of being operated whilst thebatteries are being charged, the charger shall i

21、ncorporate an isolating transformer.4.2.3.1DV D2 Replacement:Replace the first list item of 4.2.3.1 with the following: conform to UL standards where they exist;4.2.3.2DV D2 Replacement:4.2.3.2DV.1 Reduction of the risks of injury due to electric shock shall be provided inaccordance with UL 508 Indu

22、strial Control Equipment.4.2.3.3DV D2 Replacement:4.2.3.3DV.1 Overcurrent protection shall be provided in accordance with NFPA 79:1997,Electrical Standard for Industrial Machinery (National Fire Codes, Volume 3).SEPTEMBER 20, 2011 NATIONAL DIFFERENCES FOR UL UL 61496-1 5UL COPYRIGHTED MATERIAL NOT A

23、UTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4.2.3.4DV D2 Replacement:4.2.3.4DV.1 The electrical equipment shall be suitable for pollution degree 2 (see UL 840Insulation Coordination Including Clearances and Creepage Distances for ElectricalEquipment).4.2.3.5DV D2 Repl

24、acement:4.2.3.5DV.1 The electrical equipment shall be designed and constructed in accordancewith UL 508 Industrial Control Equipment.4.2.3.6DV D2 Replacement:4.2.3.6DV.1 The electrical equipment shall be wired in accordance with UL 508 IndustrialControl Equipment.4.2.4DV D2 Replacement:Replace the t

25、hird paragraph of 4.2.4 with the following:4.2.4DV.1 The output circuit(s) of the OSSDS is to be adequately protected to prevent FAILURETO DANGER, for example welded contacts under overcurrent conditions.6.1DV D2 Replacement:Replace the first sentence of 6.1 with the following:6.1DV.1 All parts of t

26、he ESPE shall bear all markings which are necessary:Replace item f) of 6.1 with the following:6.1DV.2 f) rated input power or rated current;Replace item g) of 6.1 with the following:6.1DV.3 g) designation of enclosure type;Replace item h) of 6.1 with the following:6.1DV.4 h) for double insulated equ

27、ipment only, symbol for classification for reduction ofthe risks of injury due to electric shock;6.5DV D2 Replacement of 6.5 with the following:6.5DV.1 Any enclosure which contains electrical devices shall be marked with a warningsign in accordance with NFPA 79:1997, Electrical Standard for Industri

28、al Machinery(National Fire Codes, Volume 3).6.6.2DV D2 Replacement of 6.6.2 with the following:6.6.2DV.1 Functional identification of control and indicating devices shall be provided.SEPTEMBER 20, 2011NATIONAL DIFFERENCES FOR UL UL 61496-16UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCT

29、ION ORDISTRIBUTION WITHOUT PERMISSION FROM UL6.6.3DV D2 Replacement of 6.6.3 with the following:6.6.3DV.1 The positions of any power supply switches shall be marked.6.6.4DV D2 Modification:Delete the last sentence of 6.6.4.6.7.3DV D2 Replacement of 6.7.3 with the following:6.7.3DV.1 All terminals fo

30、r the incoming supply connections shall be marked inaccordance with the Standard for Industrial Control Equipment, UL 508.6.7.4DV D2 Replacement of 6.7.4 with the following:6.7.4DV.1 Grounding and bonding conductor connection points shall be marked inaccordance with the Standard for Industrial Contr

31、ol Equipment, UL 508.7DV.1 D2 Deletion:Delete the first sentence of Section 7.7DV.2 D2 Replacement:Replace list item s) of Section 7 with the following:s) a list of color and coding systems;7DV.3 D2 Replacement:Delete the text IP from list item y) of Section 7.A.7.4DV DC Replacement:Replace the firs

32、t sentence of A.7.4 with the following:One or more visual indicators shall be provided which shall illuminate when the ESPE is ina muted condition.Table B.1.2DV DC Replacements:Replace the reference to IEC 60249-2 with UL 796.Replace the reference to IEC 60664-1 with UL 508 or UL 840.Table B.1.3DV D

33、C Replacement:Replace the text Where the terminals used are in accordance with a relevant IEC standardand the requirements of 14.1.1 and 14.1.2 of IEC 60204-1 are satisfied with the following:Where the terminals used are in accordance with UL 508.SEPTEMBER 20, 2011 NATIONAL DIFFERENCES FOR UL UL 614

34、96-1 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable B.2.1DV DC Replacements:Replace the references to IEC 60947-5-1 with UL 508.Table B.2.2DV DC Replacements:Replace the references to IEC 60664-1 with UL 508 or UL 840.Table B.3.1DV DC

35、Replacement:Replace the reference to IEC 60742 with UL 796.Table B.4.2DV DC Replacement:Replace the reference to IEC 60664-1 with UL 840.Table DVA DE Add a new annex DVA as follows:(normative)DVA.1 This annex identifies examples of terminology used in IEC 61496-1 that are notconsidered to be suitabl

36、e in the U.S. and provides that appropriate replacement text. Useof such and similar other terminology elsewhere in the IEC 61496-1 is to be similarlyreplaced.Table DVA.1 DE Addition:Table DVA.1 - TerminologySubclause reference from thisStandardText in IEC 61496-1 Appropriate replacement text for UL

37、61496-15.3.1, 6.1 f), 6.3, 6.7.6, 7 c), 7 e), 7 o),7 jj), A.4.2, A.5.3, A.6.3, A.8.1, A.8.2e)if when4.2.3.2, 4.3.4, 6.1 h) protection against reduction of the risks of injury dueto4.2.4, 4.2.9, 5.2.3.4,5.5.1, 6.8, 7 cc), 7dd), 7 ee), A.5.4, A.6.4, A.7.4, A.8.4should is to5.2.3, A.7.1.2 should whenSEPTEMBER 20, 2011NATIONAL DIFFERENCES FOR UL UL 61496-18