UL 60745-2-1 (ND)-2004 National Differences For UL 60745-2-1 Hand-Held Motor-Operated Electric Tools - Safety - Part 2-1 Particular Requirements for Drills and Impact Drills (SeconIn.pdf

《UL 60745-2-1 (ND)-2004 National Differences For UL 60745-2-1 Hand-Held Motor-Operated Electric Tools - Safety - Part 2-1 Particular Requirements for Drills and Impact Drills (SeconIn.pdf》由会员分享，可在线阅读，更多相关《UL 60745-2-1 (ND)-2004 National Differences For UL 60745-2-1 Hand-Held Motor-Operated Electric Tools - Safety - Part 2-1 Particular Requirements for Drills and Impact Drills (SeconIn.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60745-2-1Hand-Held Motor-Operated Electric Tools - Safety - Part 2-1: Particular Requirements for Drillsand Impact DrillsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURT

2、HER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60745-2-1Hand-Held Motor-Operated Electric Tools - Safety - Part 2-1: Particular Requirements for Drills andImpact DrillsEdition: 2Edition Date: March 26, 2004The revisions dated October 26, 2011 were issued to inco

3、rporate requirements to align the textof the UL and IEC versions of 60745-2-1 and to reflect the latest ANSI approval date of October26, 2011.Please note that these revisions do not involve any changes to the U.S. national differences forUL 60745-2-1.As noted in the Commitment for Amendments stateme

4、nt located on the back side of the titlepage, UL and CSA are committed to updating this harmonized standard jointly. However, therevision pages dated 2011 will not be jointly issued by UL and CSA as these revision pagesaddress UL only editorial changes.This document provides a single listing of the

5、National Differences included in the UL adoption ofthe corresponding IEC standard.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwisewithout prior permis

6、sion of UL.UL provides this standards document as is without warranty of any kind, either expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequential, indirect or simi

7、lar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof the possibility of such damage. In no event shall ULs liability for any d

8、amage ever exceed the pricepaid for this standards document, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonabl

9、eattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.Copyright Underwriters Laboratories Inc.OCTOBER 26, 2011NATIONAL DIFFERENCES FOR UL UL 60745-2-12UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REP

10、RODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Differences included in the UL adoptionof the corresponding IEC standard.In its IEC-based standards, UL uses the notations indicated below to identify national difference type,

11、 andthese types are additionally noted in this document. The standard may not use all types of thesedeviations.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich would compromise safety for U.S. consumers and users of products.D2 - These are de

12、viations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These are deviations based on the component standards and will not be deleted until a

13、particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or corrections.DR - These are deviations based on the national regulatory requirements.Each national difference contains a description of what the national difference enta

14、ils. Typically one of thefollowing words is used to explain how the text of the national difference is to be applied to the base IECtext:Addition / Add - An addition entails adding a complete new numbered clause, subclause, table,figure, or annex. Addition is not meant to include adding select words

15、 to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause,table, figure, or annex without any replacement text.Modification / Modify - A modification is an altering of the existing base IEC text such as theaddition, replacement or deletion

16、 of certain words or the replacement of an entire clause,subclause, table, figure, or annex of the base IEC text.OCTOBER 26, 2011 NATIONAL DIFFERENCES FOR UL UL 60745-2-1 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational DifferencesK.1

17、2.2DV DR Modification: Add the following to this Amendment:This subclause of part 2 is not applicable.K.12.3DV DR Modification: Replace this clause in the Amendment with the following:This subclause of the part 2 is applicable.Annex 1.DVL DE Addition: Add the following Annex:Reference National Difference TypeK.12.2DV DR ModificationK.12.3DV DR ModificationAnnex 1.DVL DE AdditionOCTOBER 26, 2011NATIONAL DIFFERENCES FOR UL UL 60745-2-14