UL 2586A-2015 UL Standard for Safety Hose Nozzle Valves for Gasoline and Gasoline Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 C E85) (First Edition Repr 2.pdf

《UL 2586A-2015 UL Standard for Safety Hose Nozzle Valves for Gasoline and Gasoline Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 C E85) (First Edition Repr 2.pdf》由会员分享，可在线阅读，更多相关《UL 2586A-2015 UL Standard for Safety Hose Nozzle Valves for Gasoline and Gasoline Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 C E85) (First Edition Repr 2.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 2586A Hose Nozzle Valves for Gasoline and Gasoline/ Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTIO

2、N OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85),

3、 UL 2586A First Edition, Dated February 20, 2015 Summary of Topics This rst edition of the Standard for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), ANSI/UL 2586A, covers hose nozzle valves that are intended to be used for

4、 the control of motor fuels. They are of the type used in motor fuel dispensing equipment. The requirements are substantially in accordance with Proposal(s) on this subject dated October 17, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or tr

5、ansmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness

6、 for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL represent

7、ative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless fr

8、om and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, exc

9、ept for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, an

10、d are preceded by a SUPERSEDED REQUIREMENTS notice. FEBRUARY 20, 2015 UL 2586A tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20, 2015 UL 2586A tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCT

11、ION OR DISTRIBUTION WITHOUT PERMISSION FROM UL February 20, 2015 1 UL 2586A Standard for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85) Prior to the rst edition, the requirements for the products covered by this standard were

12、 included in the Outline of Investigation for Hose Nozzle Valves for Gasoline and Gasoline/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), UL 2586A. First Edition February 20, 2015 This ANSI/UL Standard for Safety consists of the First Edition. The most recent designati

13、on of ANSI/UL 2586A as an American National Standard (ANSI) occurred on February 20, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to U

14、L at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and a

15、ll copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 2586A-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL FEBRUARY 20,

16、2015 UL 2586A 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Components .6 2.2 Units of measurement .7 2.3 Undated references .7 3 Glossary .7 CONSTRUCTION 4 Assembly 8

17、4.1 General .8 4.2 Hose nozzle valves .8 5 Materials 10 5.1 Metallic materials 10 5.2 Nonmetallic materials 13 5.3 Casting impregnation materials 15 5.4 Internal parts .15 5.5 Blending options 16 6 Bodies and Covers .16 7 Diaphragms .18 8 Springs .18 9 Operating Mechanisms .18 PERFORMANCE 10 General

18、 19 11 Deformation Test .20 12 Long Term Exposure Test .20 12.1 General .20 12.2 Samples 21 12.3 Method .21 12.4 Results .22 13 External Leakage Test 22 14 Hose Nozzle Valve Guard Strength Test .23 15 Operation Test .24 15.1 Automatic hose nozzle valve .24 15.2 Bellows secondary shut off operation .

19、25 16 Pull Test .25 17 Sensitivity Test .26 18 Hose Nozzle Endurance Test 26 19 Bellows Secondary Shut Off Operation Test .27 20 Visible Discharge Indicator Tests .27 20.1 Thermal shock test .27 20.2 Drop test 27 21 Hydrostatic Strength Test 27 22 Electrical Continuity Test 28 23 Salt Spray Test .28

20、 24 Moist Ammonia-Air Stress Cracking Test 29 FEBRUARY 20, 2015 UL 2586A 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 25 Marking Adhesion Test 29 26 Blending Cycling Test .30 MANUFACTURING AND PRODUCTION 27 General 30 INSTALLATION INSTRU

21、CTIONS 28 General 31 MARKING 29 General 31 SUPPLEMENT SA - Test Fluids SA.1 Details .SA1 FEBRUARY 20, 2015 UL 2586A 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover hose nozzle valves that ar

22、e intended to be used for the control of motor fuels as indicated in 1.2. They are of the type used in motor fuel dispensing equipment. Hose nozzle valves covered by this standard are for use with motor fuels which are handled at temperatures within the range of minus 29C (minus 20F) to 52C (125F) a

23、nd an operating pressure of minimum 50 psi (350 kPa). 1.2 Hoze nozzle valves covered by these requirements are intended for use with one or more of the following as applicable: a) Gasoline formulated in accordance with the Standard Specication for Automotive Spark- Ignition Fuel, ASTM D4814; b) Gaso

24、line/ethanol blends with nominal ethanol concentrations up to 25 percent ethanol (E25), consisting of gasoline formulated in accordance with the Standard Specication for Automotive Spark-Ignition Fuel, ASTM D4814, when blended with denatured fuel ethanol formulated to be consistent with the Standard

25、 Specication for Denatured Fuel Ethanol for Blending With Gasolines For Use as Automotive Spark-Ignition Engine Fuel, ASTM D4806; or c) Gasoline/ethanol blends with nominal ethanol concentrations above 25 percent formulated in accordance with the Standard Specication in item (b) or formulated in acc

26、ordance with the Standard Specication for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines, ASTM D5798. 1.3 These requirements cover hose nozzle valves of the manually operated and automatic pressure operated type. When they form a part of an assembly which provides for additi

27、onal functions or service, the requirements are outside the scope of these requirements. 1.4 These requirements do not cover the following: a) Hose nozzle valves for handling liquids under cryogenic conditions. b) Hose nozzle valves for general renery service, offshore and pipe line terminals, natur

28、al gas processing plants, gas distribution systems, petrochemical processing facilities, or the like. c) Hose nozzle valves operated wholly or partially by electricity or battery. 1.5 This standard does not cover hose nozzle valves for use with diesel, biodiesel, diesel/biodiesel blends, kerosene or

29、 fuel oil, which are covered under the Standard for Hose Nozzle Valves for Diesel Fuel, Biodiesel Fuel, Diesel/Biodiesel Blends with Nominal Biodiesel Concentrations up to 20 Percent (B20), Kerosene, and Fuel Oil, UL 2586B. FEBRUARY 20, 2015 UL 2586A 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTH

30、ER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1.6 This standard does not cover hose nozzle valves for use with liqueed petroleum gas (LP-Gas), which are covered under the Standard for Flow Control Valves for Anhydrous Ammonia and LP-Gas, UL 125. 1.7 Requirements for the installation and

31、 use of these dispensing devices are included in the Code for Motor Fuel Dispensing Facilities and Repair Garages, NFPA 30A. 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall comply with the requirements for that component. 2.1.2 A c

32、omponent is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance wi

33、th its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and

34、shall be used only under those specic conditions. 2.1.5 A hose nozzle valve with an integral swivel shall be additionally evaluated to the Electrical-Continuity and Operation Tests in the Standard for Emergency Breakaway Fittings, Swivel Connectors and Pipe-Connection Fittings for Gasoline and Gasol

35、ine/Ethanol Blends with Nominal Ethanol Concentrations up to 85 Percent (E0 E85), UL 567A. The force is to be applied at the point on the swivel farthest from the joint. When necessitated by the swivel construction, this test is to be conducted on additional samples of the swivel with the load appli

36、ed on the opposite side of the plane of rotation. See UL 567A, Figures 16.1 16.3 for examples. FEBRUARY 20, 2015 UL 2586A 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.2 Units of measurement 2.2.1 Values stated without parentheses are t

37、he requirement. Values in parentheses are explanatory or approximate information. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 F

38、or the purpose of this standard, the following denitions apply. 3.2 BLENDING OPTION Dispensing devices may be provided with an option that blends two specic fuels into one fuel to be dispensed. This blending occurs at the dispenser level and can be in two forms: a) Fixed blending Blending at the dis

39、penser level that blends two specic fuels into one fuel to be dispensed, and that fuel to be dispensed is xed. For example, xed blending includes blend options where gasoline and denatured fuel ethanol can be blended to achieve E85, which is the actual dispensed fuel. b) Variable blending Blending a

40、t the dispenser level that blends two specic fuels into the fuel to be dispensed, but the fuel to be dispensed can be any of a number of previously set points. For example, variable blending includes blend options where gasoline and E85 can be blended to achieve E40, E60, and E85 as the actual dispe

41、nsed fuel. 3.3 GASOLINE/ETHANOL BLENDS Blended fuels composed of a gasoline component and an ethanol component. The numerical value corresponding to the ethanol component determines the blend rating (such as E85 for 85% ethanol, 15% gasoline). 3.4 HOSE NOZZLE VALVE, AUTOMATIC A hose nozzle valve whi

42、ch is held open during the entire lling operation. It may be held open by manual force or by an integral hold-open or latching device. It incorporates a mechanism that shuts off the ow of liquid during refueling operations to prevent overow from the ll opening when liquid reaches a predetermined poi

43、nt on the spout. 3.5 HOSE NOZZLE VALVES A self-closing device designed to control the ow of ammable and combustible liquids at an operating pressure of minimum 50 psi (345 kPa). It is intended for use at the outlet end of a hose for dispensing ammable liquids. 3.6 HOSE NOZZLE VALVE, MANUALLY OPERATE

44、D A hose nozzle valve that is manually held open during the entire lling operation and closes only upon release of the manual force. 3.7 HOSE NOZZLE VALVE, VAPOR RECOVERY A system constructed to capture vapors displaced during lling operations. The vapors are not processed during the course of this

45、activity. a) Assist Nozzle A vacuum or pump is used to draw the vapors back to tank. b) Balance Nozzle Displacement of vapors from tank being ll forces the vapor back into the storage tank. FEBRUARY 20, 2015 UL 2586A 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WI

46、THOUT PERMISSION FROM UL 3.8 SEALS, DYNAMIC A seal that is subject to mechanical movement or other applied forces that result in movement or exing of the seal under normal use conditions. 3.9 SEALS, STATIC A seal that is not subject to mechanical movement or other applied forces other than compressi

47、ng forces that are applied during installation, after which, the seal is held in place during normal use conditions. CONSTRUCTION 4 Assembly 4.1 General 4.1.1 A hose nozzle valve shall include all of the components required for its intended function and installation. 4.1.2 A seat disc shall be attac

48、hed to its poppet or holder or otherwise assembled so as to prevent it from becoming dislocated under service conditions as determined by the Hose Nozzle Endurance Test, Section 18. The means to secure the disc shall not rely upon cement or adhesive. 4.1.3 A brazing material used for joining liquid

49、conning parts of a valve shall have a melting point (solidus temperature) of minimum 538C (1000F). 4.2 Hose nozzle valves 4.2.1 A hose nozzle valve shall be of the manually-operated or of the automatic type. A manually-operated valve requires the valve to be manually held open during the entire lling operation without the aid of hold-open devices or latches, but is capable of closing automatically. An automatic valve requires the valve to: a) Be manually opened,