UL 2158 CRD-2017 UL Standard for Safety Electric Clothes Dryers - Section Paragraph Reference 21 13 3 5 - Subject Protective Controls C clarification of Clause 21 13 3 5 (Edition .pdf
《UL 2158 CRD-2017 UL Standard for Safety Electric Clothes Dryers - Section Paragraph Reference 21 13 3 5 - Subject Protective Controls C clarification of Clause 21 13 3 5 (Edition .pdf》由会员分享,可在线阅读,更多相关《UL 2158 CRD-2017 UL Standard for Safety Electric Clothes Dryers - Section Paragraph Reference 21 13 3 5 - Subject Protective Controls C clarification of Clause 21 13 3 5 (Edition .pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared by UL LLC. It is normative for the applicable ULProduct Certification Program(
2、s); however, it is currently not part of the UL Standard(s) referencedbelow.Product Category (CCN): KMEX/KMEX7Standard Number: UL 2158Standard Title: Standard for Electric Clothes DryersEdition Date: December 18, 2015Edition Number: 4Section / Paragraph Reference: 22.2.11Subject: Metal Enclosure Thi
3、ckness (where power-supply conductors enter theenclosure)DECISION:22.2.11 At a point where the power-supply conductors enter the enclosure, sheet metal shall not be lessthan 0.81 mm thick if uncoated steel, not less than 0.86 mm if galvanized steel, not less than 1.12 mm ifaluminum, and not less tha
4、n 1.09 mm if copper or brass.22.2.11.1 Sheet metal enclosures with the dimensions specified in Tables 17.1 and 17.2 are consideredto comply with the intent of Clause 22.2.11.Table 17.1Thickness of carbon steel or stainless steel enclosuresWithout supporting frameaWith supporting frame orequivalent r
5、einforcingaMinimum thickness, mm (inch)MaximumwidthbMaximumlengthcMaximumwidthbMaximum length Uncoated Metal Coatedmm (inches) mm (inches) mm (inches) mm (inches)102 (4) Not limited 159 (6-1/4) Not limited0.51 (0.020)0.58 (0.023)121 (4-3/4) 146 (5-3/4) 171 (6-3/4) 210 (8-1/4)152 (6) Not limited 241
6、(9-1/2) Not limited0.66 (0.026)0.74 (0.029)178 (7) 222 (8-3/4) 254 (10) 318 (12-1/2)NOTE - This table is based on a uniform deflection of the enclosure surface for any given load concentrated at thecenter of the surface regardless of metal thickness.aA supporting frame is a structure of angle or cha
7、nnel or a folded rigid section of sheet metal that is rigidlyattached to and has essentially the same outside dimensions as the enclosure surface and that has sufficienttorsional rigidity to resist the bending moments that may be applied via the enclosure surface when it is deflected.Construction th
8、at is considered to have equivalent reinforcing may be accomplished by a structure that is as rigidas one built with a frame of angles or channels. Construction considered to be without supporting frame includes:Single sheet with single formed flanges (formed edges); a single sheet that is corrugate
9、d or ribbed; and Anenclosure surface loosely attached to a frame, for example, with spring clips.bThe width is the smaller dimension of a rectangular sheet metal piece that is part of an enclosure. Adjacentsurfaces of an enclosure are not prohibited from having supports in common and being made of a
10、 single sheet.cNot limited applies only where the edge of the surface is flanged at least 12.7 mm or fastened to adjacentsurfaces not normally removed in use.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 17.2Thickness of aluminum, copp
11、er, or brass enclosuresWithout supporting frameaWith supporting frame or equivalentreinforcingaMinimum thicknessMaximum widthbMaximum lengthcMaximum widthbMaximum lengthmm (inches) mm (inches) mm (inches) mm (inches) mm (inches)76 (3) Not limited 178 (7) Not limited 0.58 (0.023)89 (3-1/2) 102 (4) 21
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- UL2158CRD2017ULSTANDARDFORSAFETYELECTRICCLOTHESDRYERSSECTIONPARAGRAPHREFERENCE211335SUBJECTPROTECTIVECONTROLSCCLARIFICATIONOFCLAUSE211335EDITIONPDF
链接地址:http://www.mydoc123.com/p-1067824.html