UL 1803-2012 UL Standard for Safety Factory Follow-Up on Third Party Certified Portable Fire Extinguishers (Fourth Edition Reprint with Revisions Through and Including October 24 2.pdf

《UL 1803-2012 UL Standard for Safety Factory Follow-Up on Third Party Certified Portable Fire Extinguishers (Fourth Edition Reprint with Revisions Through and Including October 24 2.pdf》由会员分享，可在线阅读，更多相关《UL 1803-2012 UL Standard for Safety Factory Follow-Up on Third Party Certified Portable Fire Extinguishers (Fourth Edition Reprint with Revisions Through and Including October 24 2.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1803 Factory Follow-Up on Third Party Certied Portable Fire ExtinguishersUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGH

2、TED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Factory Follow-Up on Third Party Certied Portable Fire Extinguishers, UL 1803 Fourth Edition, Dated February 15, 2012 Summary of Topics This UL 1803 revision is being issued to

3、correct the ANSI approval date on the title page. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this S

4、tandard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, l

5、ost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standa

6、rd, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation

7、 introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note fol

8、lowing the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. MARCH 13, 2012 UL 1803 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DI

9、STRIBUTION WITHOUT PERMISSION FROM UL MARCH 13, 2012 UL 1803 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL February 15, 2012 1 UL 1803 Standard for Factory Follow-Up on Third Party Certied Portable Fire Extinguisher

10、s First Edition July, 1986 Second Edition November, 1994 Third Edition December, 2006 Fourth Edition February 15, 2012 This ANSI/UL Standard for Safety consists of the Fourth Edition. The most recent designation of ANSI/UL 1803 as an American National Standard (ANSI) occurred on February 15, 2012. A

11、NSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collabora

12、tive Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and ex

13、clusive property of UL. COPYRIGHT 2012 UNDERWRITERS LABORATORIES INC. ANSI/UL 1803-2012UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARCH 13, 2012 UL 1803 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTI

14、ON OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 Reference Standards 5 3 Glossary .5 4 Agreements 6 5 Certication Mark .7 6 Requirements for Third Party Certication and Inspection Body .7 THIRD PARTY CERTIFICATION BODY INSPECTION PROGRAM 7 General .8 MINIMUM MANUFACTU

15、RERS CONTROL PROGRAM 8 General .11 9 Non-DOT/TDGR Cartridge Proof-Pressure Test (+, +, +) 11 10 Non-DOT/TDGR Cartridge Burst Test (+, +, +) .11 11 Rupture Disc Assembly Test .12 12 Nitrogen Cylinder Leakage Test (+, +, +) 12 13 Cylinder Proof-Pressure Test (+, +, +, +) .12 14 Hydrostatic Burst Press

16、ure Test (+, +, +, +) 12 15 Thread Test 12 16 Pressure Regulator Test (+, +, +) .13 17 Discharge Hose and Nitrogen Hose Assembly Test .13 18 Locking Devices and Seals 13 19 Discharge Duration, Minimum Dry Chemical Discharged, and Weight of Charge Determinations (Hand Extinguishers) (+) .14 20 Discha

17、rge Duration and Weight of Carbon Dioxide Determinations (Hand Extinguishers) (+) .14 21 Discharge Duration, Minimum Extinguishing Agent Discharged, and Range of Discharge (+, +) 15 22 Rate-of-Flow Test (+) .15 23 Discharge Tests (Wheeled Extinguishers) (+, +, +, + ) 15 24 Cartridge Assembly Leakage

18、 Test (+, +, +) 16 25 Extinguisher Leakage Test .16 26 Pressure Gauge/Indicator Test (+, +, +, +) 17 27 Dry Chemical Extinguishing Agent Tests (+) .17 27.1 General .17 27.2 Sieve test .18 27.3 Hygroscopicity Test .18 27.4 Water repellency test .18 27.5 Packed chamber test .19 28 Horn Impact Test (+)

19、 19 29 Test Records .19 30 Calibration of Testing and Measuring Equipment .20 FEBRUARY 15, 2012 UL 1803 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INSPECTORS COUNTERCHECK PROGRAM AT FACTORY 31 Verication of Material .20 32 Examination

20、of Parts and Subassemblies 20 33 Critical Dimensions and Parts Verication 21 34 Visual Inspection of Completed Extinguishers 21 35 Countercheck Tests Each Inspection 23 36 Periodic Countercheck Tests .24 37 Review of Records 24 TESTS TO BE CONDUCTED AT TEST LABORATORY 38 Frequency of Test 24 39 Salt

21、 Spray Test .24 40 Qualitative Infrared Analysis 24 41 Extinguishing Agent Tests (+) 25 42 Extinguisher Tests (Hand Extinguishers) (+) .25 43 Freezing Point Determination of Antifreeze Charge (+) .25 43.1 Apparatus .25 43.2 Method .25 43.3 Results .26 44 Foam Quality (+) .26 44.1 Apparatus .26 44.2

22、Method .26 44.3 Results .27 45 Foam Identication Tests - Specic Gravity (+) 27 45.1 General .27 45.2 Qualitative infrared analysis .27 46 Carbon Analysis of Stainless Steel Cylinders (+, +) .27 46.1 Apparatus .27 46.2 Method .27 46.3 Results .27 CONTROL OF CERTIFICATION MARK 47 Inspection Program .2

23、7 48 Frequency of Inspections 28 FEBRUARY 15, 2012 UL 1803 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 This standard covers the basic elements of a Third Party Certication and Inspection Program for various type

24、s of portable re extinguishers, hand and wheeled, including the following: carbon dioxide, dry chemical, water based, clean agent, and stored pressure water. 2 Reference Standards 2.1 Products covered under this program shall comply with the requirements in effect on the date of production in the St

25、andard for the Rating and Fire Testing of Fire Extinguishers, ANSI/UL 711, and in one of the following standards: a) Standard for Water Based Agent Fire Extinguishers, ANSI/UL 8. b) Standard for Carbon Dioxide Fire Extinguishers, ANSI/UL 154. c) Standard for Dry-Chemical Fire Extinguishers, ANSI/UL

26、299. d) Standard for Water Fire Extinguishers, ANSI/UL 626. e) Standard for Clean Agent Fire Extinguishers, ANSI/UL 2129. 3 Glossary 3.1 For the purpose of this standard, the following denitions apply. 3.2 CERTIFICATION A process of product evaluation to: a) Determine conformance of a product with a

27、 nationally-recognized safety standard; b) Provide for product Listing in a product directory; c) Provide for application of a Certication Mark to those products which conform to the standard; and d) Provide for audit of a manufacturers quality control program, all under terms of an agreement(s) sig

28、ned by the manufacturer and the Third Party Certication and Inspection Body. 3.3 CERTIFICATION MARK A distinctive registered mark of a Third Party Certication and Inspection Body that the Manufacturer, by the terms of the Third Party Certication and Inspection Body, is authorized to apply to his pro

29、duct as his declaration that the product has been manufactured under the Follow-Up Program and complies with the requirements of the program. 3.4 FOLLOW-UP DOCUMENT A document describing the Certied product and essential elements of the Follow-Up Program, prepared by the Third Party Certication and

30、Inspection Body and loaned to the Manufacturer while the Certication is in effect. FEBRUARY 15, 2012 UL 1803 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3.5 FOLLOW-UP PROGRAM The sampling, inspections, tests, or other measures taken by

31、the Manufacturer and supplemented by the Certication Body as a check on the means that the Subscriber exercises to determine compliance of Certied products with the requirements. Such activities are generally conducted at the manufacturing location, but examination and testing is also conducted by t

32、he Certication and Inspection Body on samples selected from the factory, the open market, or elsewhere. 3.6 MANUFACTURER A manufacturer or assembler of a Certied product at whose factory a Third Party Certication and Inspection Program is established. 4 Agreements 4.1 A manufacturer participating in

33、 the Third Party Certication and Inspection Program shall be required to sign a legally binding agreement with a Third Party Certication Body. Such an agreement shall provide for at least the following elements, duties, and responsibilities: a) The Certication Body shall determine, by means of produ

34、ct evaluation and review of the Manufacturers quality assurance measures, that the product is eligible for coverage under a Certication Program. b) The manufacturer shall agree that the Certication and Inspection Body may test production samples or prototype models. If a prototype model is tested, t

35、he Certication and Inspection Body shall inspect the rst production and repeat selected tests to verify that the production samples comply with the appropriate requirements. Products that comply will be covered under a Follow-Up Program as indicated in (c), and will be subject to additional producti

36、on sampling and testing as described in (g) and (h). c) The Certication and Inspection Body shall prepare a Follow-Up Document, publish a Listing in a suitable form, and establish a Follow-Up Program for a product found to be in compliance with the appropriate standards and otherwise to be eligible

37、for coverage under the Certication Program. d) The Follow-Up Inspection Document shall identify, describe, and set forth requirements for the Certied product and shall specify the authorized Certication Mark that shall be used only on or in connection with a Certied product. e) The establishment of

38、coverage under the Program shall be contingent upon the manufacturer demonstrating to the Certication Bodys satisfaction that the product will be produced in accordance with the Certication Program. f) The manufacturer shall agree that the Certication Mark shall only be used on products manufactured

39、 by him at the locations specied in the Follow-Up Document. g) Under a Follow-Up Program, the Certication and Inspection Body shall perform all necessary examinations, tests, and inspections to determine compliance of randomly selected samples of the Certied product with the requirements specied in

40、the Follow-Up Inspection Document. Samples are to be selected from production intended to bear the Certication Mark, nished products at the manufacturers factory bearing the Certication Mark, and products that bear the Certication Mark that have been purchased on the open market. h) The Certication

41、and Inspection Body shall have the right to conduct unannounced inspections at the factory, and to control Certication Marks, including the right to require that the manufacturer remove a Mark from a product that does not comply with the requirements. FEBRUARY 15, 2012 UL 1803 6UL COPYRIGHTED MATERI

42、AL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL i) The manufacturer shall agree to have the product investigated by the Certication and Inspection Body to determine compliance with changes in standards or shall agree to discontinue application of the Certication

43、 Mark when such changes become effective. 5 Certication Mark 5.1 The Certication and Inspection Body shall permit the use of a Certication Mark only on products that comply with all of the requirements of the Certication and Inspection Program. The Certication Mark shall be owned and controlled by t

44、he Certication and Inspection Body, shall be used exclusively to identify products as being Certied, and shall be Federally registered as a Certication Mark with the U. S. Patent and Trademark Office under the Trademark Act of 1946, commonly referred to as the Lanham Act ( 15 U.S.C. 1051 et. seq.).

45、6 Requirements for Third Party Certication and Inspection Body 6.1 To qualify as a Third Party Certication Body, a Certication Body shall be recognized by the authority having jurisdiction as: a) Being engaged, as a regular part of its business, in performing inspections and tests that are the same

46、as or similar to the inspections and tests required for the product being considered for Certication; b) Having, or having access to, the equipment, facilities, personnel, and calibrated instruments that are necessary to inspect and test the products under the Certication Program; c) Not being owned

47、 or controlled by: 1) A manufacturer, vendor, or buyer of the products to be inspected or tested, or by a manufacturer of similar products. 2) A supplier of materials to the manufacturer. d) Having sufficient breadth of interest or activity, so that loss or award of a specic contract to determine co

48、mpliance of a product would not be a substantial factor in the nancial well-being of the Certication Body; e) Not advertising, promoting, or designing the manufacturers product nor performing consulting work for the manufacturer of products covered under the Certication Program that impairs the impa

49、rtiality of the Certication Body; f) Not contracting or transferring to another person or organization responsibility for the performance or supervision of inspections or tests, or both, required under the Certication Program; and g) Providing a mechanism for appealing decisions of the Certication Body to a panel of noncommercially involved third parties. FEB