UL 1681-2012 UL Standard for Safety Wiring Device Configurations (Fourth Edition Reprint with revisions through and including July 15 2016)《布线设备配置》.pdf

《UL 1681-2012 UL Standard for Safety Wiring Device Configurations (Fourth Edition Reprint with revisions through and including July 15 2016)《布线设备配置》.pdf》由会员分享，可在线阅读，更多相关《UL 1681-2012 UL Standard for Safety Wiring Device Configurations (Fourth Edition Reprint with revisions through and including July 15 2016)《布线设备配置》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1681 Wiring Device CongurationsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER RE

2、PRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Wiring Device Congurations, UL 1681 Fourth Edition, Dated April 10, 2012 Summary of Topics This new edition of UL 1681 is being issued to: Reect the Designation of UL 1681 as an ANSI Standard and to Include Figure C3.1

3、to Illustrate an Alternate Plug Blade Prole Incorporating Insulating Material for Use with Electrical Utilization Equipment The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated January 27, 2012. All rights reserved. No part of this publication may b

4、e reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, t

5、he implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this S

6、tandard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety ag

7、ree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The req

8、uirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future

9、effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. APRIL 10, 2012 UL 1681 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 10, 2012 UL 1681 tr2 No Text on This PageUL COPYRIGHTED MATE

10、RIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL April 10, 2012 1 UL 1681 Standard for Wiring Device Congurations Prior to the rst edition, the congurations were published in the Standard for Attachment Plugs and Receptacles, UL 498. First Edition April, 1991 S

11、econd Edition April, 1996 Third Edition March, 2003 Fourth Edition April 10, 2012 This ANSI/UL Standard for Safety consists of the Fourth Edition. The most recent designation of ANSI/UL 1681 as an American National Standard (ANSI) occurred on April 10, 2012. ANSI approval for a standard does not inc

12、lude the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS)

13、 at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2012 U

14、NDERWRITERS LABORATORIES INC. ANSI/UL 1681-2012UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DIS

15、TRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 General 4 CONFIGURATIONS C1 Non-NEMA Plugs and Receptacles 5 C2 Alternate Shrouding Congurations .11 C3 Insulated Blade Prole for a 2-Pole, 2-Wire, 1A, 125 V AC Only Attachment Plug .14 APRIL 10, 2012 WIRING DEVICE CONFIGURATION

16、S - UL 1681 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These congurations cover attachment plugs, receptacles, cord connectors, some forms of current taps, and atiron and appliance plugs all for use in accordan

17、ce with the National Electrical Code (NEC), ANSI/NFPA-70. 1.2 These congurations do not cover devices rated at more than 200 A or for more than 600 V. 1.3 This standard does not cover devices having NEMA congurations in accordance with Wiring Devices Dimensional Specications, ANSI/NEMA WD6. 2 Genera

18、l 2.1 The information given in (a) (h) applies to each conguration in Sections C1 C3. a) All dimensions are in inches. b) Decimal dimensions without tolerances shall be subject to a 0.005 inch tolerance. c) Angular dimensions without tolerances shall be subject to a 1/2 degree tolerance. d) Where tw

19、o values are given for the same dimension, the larger is the maximum value and the smaller the minimum value. e) Leading edges of plug blades shall be free of burrs and sharp edges. f) A contour, face dimension, yoke construction, or mounting ears and dimensions for any receptacle construction that

20、is shown depicts an acceptable construction; other constructions may also be acceptable if tested and found to be equivalent. g) A relationship of contact nibs, recess of contacts, or internal construction in a receptacle that is shown depicts an acceptable construction; other constructions may also

21、 be acceptable if tested and found to be equivalent. h) Terminal Identication shall comply with the following: 1) The grounded terminal shall be identied in the Figures by the letter W . 2) The grounding terminal shall be identied in the Figures by the letter G . 3) Other conductors need not be iden

22、tied, but if they are, the letters X , Y , and Z shall be used for identication according to the following convention: i) Viewing the blade end of the plug and proceeding counter-clockwise, starting from the grounding blade (G), or in the absence of a grounding blade, the grounded blade (W), the ter

23、minals shall be marked in sequence X , Y , and Z . APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL ii) Viewing the face end of the receptacle and proceeding clockwise, starting from the

24、grounding contact slot (G), or in the absence of a grounding contact slot, the grounded contact slot (W), the terminals shall be marked in sequence X , Y , and Z . CONFIGURATIONS C1 Non-NEMA Plugs and Receptacles This is generated text for gtxt. APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681

25、5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This is generated text for gtxt. Figure C1.1 Hospital use only 2-pole, 3-wire grounding-type locking devices rated 20 A, 125 V APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 6UL COPYRIG

26、HTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This is generated text for gtxt. Figure C1.2 3-pole, 3-wire nongrounding-locking devices rated 20 A, 125/250 V APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 7UL COPYRIGHTED MATERIAL NOT AUTHORIZE

27、D FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This is generated text for gtxt. Figure C1.3 3-pole, 3-wire nongrounding-locking devices rated 30 A, 125/250 V APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

28、OR DISTRIBUTION WITHOUT PERMISSION FROM UL This is generated text for gtxt. Figure C1.4 4-pole, 4-wire nongrounding-locking devices rated 20 A, 120/208 V 3-phase wye APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION

29、 WITHOUT PERMISSION FROM UL Figure C1.5 4-pole, 4-wire nongrounding-locking devices rated 30 A, 120/208 V 3-phase wye APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 10UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL C2 Alternate Shroud

30、ing Congurations This is generated text for gtxt. APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 11UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.1 Alternate shrouding conguration, male devices APRIL 10, 2012 WIRING DEVICE

31、CONFIGURATIONS - UL 1681 12UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure C2.2 Alternate shrouding conguration, female devices APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 13UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

32、 REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL C3 Insulated Blade Prole for a 2-Pole, 2-Wire, 1A, 125 V AC Only Attachment Plug This is generated text for gtxt. APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 14UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRI

33、BUTION WITHOUT PERMISSION FROM UL Figure C3.1 Solid blade with insulation material provided on minor plug blade of a 2-pole, 2-wire, non- polarized attachment plug rated 1A, 125 V AC only Notes: 1. Blade thickness and location within an attachment plug shall comply with ANSI/NEMA WD6. 2. When both e

34、dges are provided with insulating material, each edge of insulating material shall be 0.0075 inches. 3. The overall thickness of the insulating material when applied to either or both blade edges shall not exceed the overall blade thickness of 0.260 inches along any area of the 0.170 inch maximum bl

35、ade length. 4. Only permitted for non-polarized attachment plug blade construction. APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 15UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL APRIL 10, 2012 WIRING DEVICE CONFIGURATIONS - UL 1681 16 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL