UL 1598B-2000 UL Standard for Safety Supplemental Requirements for Luminaire Reflector Kits for Installation on Previously Installed Fluorescent Luminaires (First Edition Reprint w.pdf

《UL 1598B-2000 UL Standard for Safety Supplemental Requirements for Luminaire Reflector Kits for Installation on Previously Installed Fluorescent Luminaires (First Edition Reprint w.pdf》由会员分享，可在线阅读，更多相关《UL 1598B-2000 UL Standard for Safety Supplemental Requirements for Luminaire Reflector Kits for Installation on Previously Installed Fluorescent Luminaires (First Edition Reprint w.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1598B Supplemental Requirements for Luminaire Reector Kits for Installation on Previously Installed Fluorescent LuminairesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR D

2、ISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Supplemental Requirements for Luminaire Reector Kits for Installation on Previously Installed Fluorescent Luminaires, UL 1598B F

3、irst Edition, Dated December 4, 2000 Summary of Topics This revision to ANSI/UL 1598B includes the following changes in requirements: Clarify Requirements for Luminaire Retrot Kits that Provide Replacement Lampholders or Instant Start Ballasts Text that has been changed in any manner or impacted by

4、ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on which the changed requirement becomes effective. The new a

5、nd revised requirements are substantially in accordance with Proposal(s) on this subject dated February 28, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording,

6、 or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, conseq

7、uential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs lia

8、bility for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including

9、reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Sta

10、ndard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. SEPTEMBER 25, 2014 UL 1598B tr1

11、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SEPTEMBER 25, 2014 UL 1598B tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL December 4, 2000 (Title Page Repri

12、nted: September 25, 2014) 1 UL 1598B Standard for Supplemental Requirements for Luminaire Reector Kits for Installation on Previously Installed Fluorescent Luminaires First Edition December 4, 2000 This ANSI/UL Standard for Safety consists of the First Edition including revisions through September 2

13、5, 2014. The most recent designation of ANSI/UL 1598B as an American National Standard (ANSI) occurred on September 25, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of

14、 the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in

15、any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2014 UNDERWRITERS LABORATORIES INC. ANSI/UL 1598B-2014UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHO

16、UT PERMISSION FROM UL SEPTEMBER 25, 2014 UL 1598B 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Components .6 2.2 Units of measurement .6 2.3 Undated references .6 MECH

17、ANICAL CONSTRUCTION 3 General 6 4 Polymeric Materials .7 5 Air-Handling Luminaire Reectors .7 6 Adhesives 7 7 Metal Thickness 8 ELECTRICAL CONSTRUCTION 8 General 8 9 Grounding 8 10 Lampholders .10 11 Wiring and Conductors 10 12 Ballasts 10 MARKING AND INSTRUCTIONS 13 General 10A 14 Identication .13

18、15 Installation Marking .13 16 Installation Instructions 13 APPENDIX A Standards for ComponentsA1 SEPTEMBER 25, 2014 UL 1598B 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This page intentionally left blank. APRIL 26, 2005 UL 1598B 4UL CO

19、PYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Standard for Supplemental Requirements for Luminaire Reector Kits for Installation on Previously Installed Fluorescent Luminaires INTRODUCTION 1 Scope 1.1 This Standard applies to reector kits that

20、consist of one or more components that are intended to be installed in uorescent luminaires sometime after the initial installation of the luminaire. These requirements are supplementary to the other applicable requirements in the Standard for Luminaires, UL 1598. The components of a reector kit are

21、 reectors, ballasts, lampholders, wiring, brackets, wire connectors, or similar items. References to requirements in the Standard for Luminaires, UL 1598 are in italics for easy identication. 1.2 Table 1.1 denes the types of reector kits covered by the requirements in this Standard based on the task

22、s involved in the installation of a reector kit. The installation of a Type I reector kit shall involve only those tasks that correspond to its reector kit type in Table 1.1. A Type II reector kit is able to involve the tasks of kit types I and II. Table 1.1 Reector kit types Reector kit types Tasks

23、 involved I Reector installation Reector replacement II Lampholder relocation, removal, or replacement Ballast relocation, removal, or replacement Wire relocation, removal, replacement, or addition 1.3 A product that contains features, characteristics, components, materials, or systems new or differ

24、ent from those covered by the requirements in this standard, and that involves a risk of re or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of this

25、 standard. A product whose features, characteristics, components, materials, or systems conict with specic requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development,

26、revision, and implementation of this standard. DECEMBER 4, 2000 UL 1598B 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2.1 Components 2.1.1 Except as indicated in 2.1.2, a component of a product covered by this standard shall co

27、mply with the requirements for that component. See Appendix A for a list of standards covering components used in the products covered by this standard. 2.1.2 A component is not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application

28、 of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.1.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.1.4 Specic components are incomplete in construction features or restricte

29、d in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 2.2 Units of measurement 2.2.1 Values stated without parentheses are the requirement. Va

30、lues in parentheses are explanatory or approximate information. 2.3 Undated references 2.3.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. MECHANICAL CONSTRUCTION 3 General

31、3.1 After installation of a reector kit, a luminaire shall comply with the requirements in Mechanical construction, Section 5, of UL 1598. 3.1 revised April 26, 2005 3.2 After installation of a reector kit, all components of the reector kit and all components of the luminaire that were affected by t

32、he installation of the reector kit shall be secured in place so that lamp replacement, inspection of splices to the branch-circuit supply wires, and routine maintenance will not loosen components or joints in the assembly. 3.3 Fluorescent lamps shall not be relied upon for support of any reector kit

33、 component. APRIL 26, 2005 UL 1598B 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3.4 A reector shall be secured in place by brackets, horizontal overlapping anges, screws, or equivalent mechanical means. Friction shall not be relied upon

34、 to secure the reector in place. The securement means shall be such that it will withstand any unintentional contact that occurs during lamp replacement. 4 Polymeric Materials 4.1 A polymeric material serving to complete the enclosure required in Enclosures, Subsection 5.3, of UL 1598, or providing

35、structural support of any electrical component or of any non-electrical component weighing more than 3 ounces (85 g) shall comply with the requirements in Polymeric materials, Subsection 5.7, of UL 1598. 4.1 revised April 26, 2005 4.2 A metallized polymeric reector that is spaced within 3 inches (76

36、.2 mm) from any lampholder, lamp contact, lampholder lead, wiring, or other electrical component (excluding the uorescent lamps) that are below the metallized surface shall comply with the applicable requirements for metallized plastic parts in Polymeric Materials Use in Electrical Equipment Evaluat

37、ions, UL 746C. 4.2 revised August 22, 2002 5 Air-Handling Luminaire Reectors 5.1 A reector kit intended for installation in a luminaire used as an air handling register shall not impede the intended air ow. 5.2 A nonmetallic material, adhesive, or adhesive tape used in a reector kit intended for ins

38、tallation in a luminaire used as an air handling register shall comply with Air-handling luminaires, Subsection 12.2, of UL 1598. 5.2 revised April 26, 2005 6 Adhesives 6.1 An adhesive or adhesive tape shall not be relied upon to secure any part to a panel, bracket, or component of a luminaire. 6.2

39、An adhesive or adhesive tape that complies with the requirements for temperature, humidity, and indoor cyclic conditioning for adhesives in UL 746C is able to be relied upon to secure a part of a reector kit to another part of a reector kit. With regard to the temperature conditioning, a normal oper

40、ating temperature of 90C (194F) shall be assumed unless temperature testing of the luminaire/kit combination indicates that a lower normal operating temperature applies. This requirement applies to all adhesives including an adhesive used to secure a metal foil reecting surface or a laminate reectin

41、g surface to the reector base material. APRIL 26, 2005 UL 1598B 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 7 Metal Thickness 7.1 Metal parts of a reector kit and those portions of a luminaire affected by installation of the reector kit

42、 shall comply with the requirements in Metal thickness for enclosures, Subsection 5.5, of UL 1598. 7.1 revised April 26, 2005 ELECTRICAL CONSTRUCTION 8 General 8.1 After installation of a reector kit, a luminaire shall comply with the requirements in Electrical construction, Section 6, of UL 1598. 8

43、.1 revised April 26, 2005 8.2 Installation of a reector kit shall not change: a) The method by which the luminaire is connected to the branch circuit; or b) Any portion of the luminaire applicable to the requirements for Supply connections, Subsection 6.15, of UL 1598. 8.2 revised April 26, 2005 8.3

44、 Installation of a reector kit shall not require alteration of the construction of lampholders, ballasts, or other electrical components. 9 Grounding 9.1 An electrically conductive reector spaced within 3 inches (76.2 mm) from all lampholders, lamp contacts, lampholder leads, wiring, and other elect

45、rical components (excluding the uorescent lamps) that are below the metal surface shall be grounded. See Figure 9.1. This is generated text for gtxt. APRIL 26, 2005 UL 1598B 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Figure 9.1 Spacing

46、s for metal reecting surface of reector kit A. Open hole in lampholder bracket through which the lampholder leads pass B. Exposed lampholder leads C. Bracket on which the lampholder is mounted D. Lampholder DECEMBER 4, 2000 UL 1598B 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR

47、 DISTRIBUTION WITHOUT PERMISSION FROM UL 10 Lampholders 10.1 Installation of a Type II reector kit that involves relocation or removal of lampholders and lampholder leads originally supplied with the luminaire shall comply with the requirements in this section. 10.2 Replacement lampholders provided

48、as a part of a reector kit shall be suitable for use with the type of uorescent lamp marked on the ballast involved and be of the type to comply with the Standard for Luminaires, UL 1598, if used to retrot a luminaire provided with an instant-start electronic ballast. 10.2 revised September 25, 2014

49、 10.3 After installation of a reector kit, lampholder connections shall comply with the requirements in Lampholders, Subsection 8.4, of UL 1598. 10.3 revised April 26, 2005 11 Wiring and Conductors 11.1 Supplemental wiring or connectors required for installation of the reector kit shall be included in the kit. The connectors shall be suitable for the number and size of conductors with which they are intended to be used. The supplemental wiring shall com