UL 1565-2013 UL Standard for Safety Positioning Devices (Fifth Edition Reprint with revisions through and including May 5 2017)《电线定位装置》.pdf

《UL 1565-2013 UL Standard for Safety Positioning Devices (Fifth Edition Reprint with revisions through and including May 5 2017)《电线定位装置》.pdf》由会员分享，可在线阅读，更多相关《UL 1565-2013 UL Standard for Safety Positioning Devices (Fifth Edition Reprint with revisions through and including May 5 2017)《电线定位装置》.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1565 Positioning DevicesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCT

2、ION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Positioning Devices, UL 1565 Fifth Edition, Dated January 25, 2013 SUMMARY OF TOPICS This new edition of ANSI/UL 1565 includes changes to the scope of the standard due to the removal of the requirements for cable tie and cable

3、 tie accessories. The new requirements are substantially in accordance with Proposal(s) on this subject dated September 28, 2012. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocop

4、ying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, in

5、cidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no eve

6、nt shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judg

7、ment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other ele

8、ments of the Standard having future effective dates as indicated in the preface. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. The following table lists the future eff

9、ective dates with the corresponding reference. JANUARY 25, 2013 UL 1565 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Future Effective Date Reference June 1, 2014 Entire Standard JANUARY 25, 2013 UL 1565 tr2UL COPYRIGHTED MATERIAL NOT A

10、UTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CSA Group CSA C22.2 No. 18.5-13 Second Edition Underwriters Laboratories Inc. UL 1565 Fifth Edition Positioning Devices January 25, 2013 ANSI/UL 1565-2013UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR D

11、ISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Canadian Standards Association (operating as CSA Group) and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA Group or UL

12、 at any time. Revisions to this standard will be made only after processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will issue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ISBN 978-1-7

13、7139-015-6 2013 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subject to periodic review, and suggestions for its improvement will be referred to the appropriate committee. To submit

14、 a proposal for change, please send the following information to inquirescsagroup.org and include Proposal for change in the subject line: Standard designation (number); relevant clause, table, and/or gure number; wording of the proposed change; and rationale for the change. To purchase CSA Group St

15、andards and related publications, visit CSA Groups Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2013 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any

16、way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the Fifth Edition. The most recent designation of ANSI/UL 1565 as an American National Standard (ANSI) occur

17、red on January 23, 2013. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page (front and back), or the Preface. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Requ

18、est in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .5 1 Scop

19、e .7 2 Dated and undated references 7 3 Normative references 7 4 Denitions 8 5 Classication .9 6 General requirements 10 7 Marking .11 7.1 General 11 7.2 Specic markings based on classication .11 8 General notes on tests .12 9 Mechanical strength requirements .13 10 Polymeric materials .14 10.1 Flam

20、mability classication .14 10.2 Relative thermal index rating .14 10.3 Substitution of materials .15 10.4 Material requirements .15 11 Corrosion resistance 15 12 Sharp edges .16 13 Installation test .16 14 Mechanical strength test method .16 14.1 General .16 14.2 Assembly for test Positioning Devices

21、 .17 14.3 Assembly for test Separate Mounting Devices .18 15 Mechanical strength/elevated temperature test Wiring Ducts .19 16 Environmental conditioning .19 17 Smoke and heat release tests 20 TABLES .21 FIGURES 22 ANNEX A ADHESIVES (Normative) A1 Scope .27 A2 Requirements 27 A3 Method General 27 A4

22、 As-received test 27 A5 Effect of temperature 28 A6 Effect of humidity .30 A7 Effect of cold .30 A8 Effect of cyclic conditions 30 A9 Other test considerations 30 JANUARY 25, 2013 CSA C22.2 NO. 18.5-13 UL 1565 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT P

23、ERMISSION FROM UL ANNEX B WATER AND ULTRAVIOLET LIGHT EXPOSURE (Normative) B1 Retention of mechanical strength following water and ultraviolet light exposure 32 B2 Normative references .32 B3 Ultraviolet light exposure 32 B3.1 Apparatus .32 B3.2 Method .33 ANNEX C SMOKE AND HEAT RELEASE TEST (Normat

24、ive) C1 Scope .34 C2 Apparatus .34 C2.1 General .34 C2.2 Ignition source .34 C2.3 Test frame enclosure and burner 36 C2.4 Collection hood and exhaust duct 38 C2.5 Velocity measuring instruments 40 C2.6 Gas sampling and analysis equipment 42 C2.7 Smoke measuring instruments .42 C2.8 Data acquisition

25、42 C3 Pretest calibration 42 C3.1 Oxygen analyzer .42 C3.2 Heat release rate 43 C3.3 Photometer system .44 C4 Test procedure .44 C4.1 Initial preparation 44 C4.2 Procedure .44 C5 Calculations .44 C5.1 Calibration constant 44 C5.2 Heat release rate 45 C5.3 Smoke release rate 47 C5.4 Normalized optica

26、l density 47 C6 Report 48 ANNEX D SUBSTITUTION OF MATERIALS (Informative) D1 Normative references .49 D2 Criteria for substitution of materials .49 ANNEX E POLYMERIC MATERIAL MODIFICATIONS (Informative) E1 Regrind material 50 E2 Additives used in the molding process 50 E3 Blending materials 51 JANUA

27、RY 25, 2013 CSA C22.2 NO. 18.5-13 UL 1565 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the harmonized CSA Group and UL Standard for Positioning Devices. It is the second edition of CSA C22.2 No. 18.5, and the fth edition

28、of UL 1565. This edition of CSA-C22.2 No. 18.5 supersedes the previous edition published in 2002. This edition of UL 1565 supersedes the previous edition published in 2002. This harmonized Standard was prepared by Underwriters Laboratories and CSA Group. The efforts and support of the members of the

29、 Technical Harmonization Committee, which includes end product manufacturers and material suppliers, are gratefully acknowledged. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was reviewed by the Technical Subcommittee o

30、n ICCM03-Fittings, Hardware and Positioning Devices, under the jurisdiction of the Technical Committee on Wiring Products, and has been formally approved by the Technical Committee. This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard.

31、Where reference is made to a specic number of samples to be tested, the specied number is considered a minimum quantity. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to

32、 judge its suitability for their particular purpose. Level of harmonization This Standard is published as an equivalent standard for CSA and UL. An equivalent standard is a standard that is substantially the same in technical content except as follows. Technical deviations are allowed for Codes and

33、Governmental Regulations, and those recognized as being in accordance with NAFTA Article 905, for example because of fundamental, climatic, geographical, technological or infrastructural factors, scientic justication or the level of protection that the country considers appropriate. Presentation is

34、word for word except for editorial changes. Interpretations The interpretation by the SDO (Standards Development Organization) of an equivalent standard shall be based on the literal text to determine compliance with the standard in accordance with the procedural rules of the SDO. If more than one i

35、nterpretation of the literal text has been identied, a revision shall be proposed as soon as possible to each of the SDOs to more accurately reect the intent. CSA Group effective date The effective date for CSA Group will be announced through CSA Informs or a CSA Group certication notice. UL effecti

36、ve date As of June 1, 2014, all products Listed or Recognized by UL must comply with the requirements in this standard. JANUARY 25, 2013 CSA C22.2 NO. 18.5-13 UL 1565 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Between January 25, 2013

37、and June 1, 2014, new product submittals to UL may be evaluated under all requirements in this standard or, if requested in writing, evaluated under presently effective requirements only. The presently effective requirements are contained in the fourth edition of UL 1565. A UL effective date is one

38、established by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. JANUARY 25, 2013 CSA C22.2 NO. 18.5-13 UL 1565 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1 Scope 1.1 This standard applies to those metallic

39、and nonmetallic devices used for positioning which may include bundling and securing or to a limited extent supporting cable, wire, conduit, or tubing of a wiring system in electrical installations, to reduce the risk of re, electric shock, or injury to persons. This standard applies to, but is not

40、limited to, cable clamps, cable and conduit clips, and non-raceway wiring ducts. 1.2 These requirements do not apply to cable ties or cable tie accessories, coated electrical sleeving, extruded insulating tubing, metallic or nonmetallic raceways or woven exible nonmetallic tubing (ber loom) employed

41、 as mechanical protection for insulated wires or equipment covered by other standards or requirements. Note 1: Cable ties and cable tie accessories are covered in the Standard for Cable Ties for Electrical Installations, CAN/CSA-C22.2 No. 62275 or UL 62275. Note 2: Nonmetallic Mechanical Protective

42、Tubing (NMPT) is covered in the Standard for Nonmetallic Mechanical Protective Tubing (NMPT), CSA C22.2 No. 227.3 or UL 1696. 1.3 These requirements do not apply to any mechanical protection or electrical insulation that is provided by these devices. 1.4 These requirements do not apply to hardware f

43、or the support of conduit, tubing, and cable from a building structure, such as hangers, staples, straps, and similar devices for installation in accordance with the National Electrical Code, NFPA 70, and the Canadian Electrical Code (CE Code) Part I. Note: Hardware for the support of conduit, tubin

44、g, and cable from a building structure such as hangers, staples, straps, and similar devices for installation in accordance with the National Electrical Code, NFPA 70, and the Canadian Electrical Code (CE Code) Part I are covered in the Standard for Hardware for the Support of Conduit, Tubing, and C

45、able, CSA C22.2 No. 18.4 or UL 2239. 1.5 In Canada, the requirements in this standard generally address class of workmanship in accordance with the Canadian Electrical Code (CE Code) Part 1, and where applicable, minor combustible components in the National Building Code of Canada. 2 Dated and undat

46、ed references 2.1 For undated references to Standards, such references shall be considered to refer to the latest edition and all amendments to that edition up to the time when this Standard was approved. For dated references to Standards, such references shall be considered to refer to the dated ed

47、ition and all amendments published up to the time the Standard was approved. 3 Normative references CSA Group Standards C22.1-12 Canadian Electrical Code, Part I CAN/CSA-C22.2 No. 0-10 General Requirements Canadian Electrical Code, Part II JANUARY 25, 2013 CSA C22.2 NO. 18.5-13 UL 1565 7UL COPYRIGHT

48、ED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CAN/CSA-C22.2 No. 0.17-00 Evaluation of Properties of Polymeric Materials C22.2 No. 18.4-04 Hardware for the Support of Conduit, Tubing, and Cable UL Standards UL 746B Polymeric Materials Long Term Propert

49、y Evaluations UL 2239 Hardware for the Support of Conduit, Tubing, and Cable ASTM Standards ASTM B117-97 Standard Practice for Operating Salt-Spray (Fog) Apparatus IEC Standards IEC 60216-4-1 (2006) Guide for the Determination of Thermal Endurance Properties of Electrical Insulating Materials Part 4: Aging Ovens Section One: Single Chamber Ovens (Third Edition) IEC 60695-11-10 (2003) Fire Hazard Testing Part 11-10: Test Flames 50 W H