UL 1285-2016 UL Standard for Safety Pipe and Couplings Polyvinyl Chloride (PVC) and Oriented Polyvinyl Chloride (PVCO) for Underground Fire Service (Sixth Edition).pdf

《UL 1285-2016 UL Standard for Safety Pipe and Couplings Polyvinyl Chloride (PVC) and Oriented Polyvinyl Chloride (PVCO) for Underground Fire Service (Sixth Edition).pdf》由会员分享，可在线阅读，更多相关《UL 1285-2016 UL Standard for Safety Pipe and Couplings Polyvinyl Chloride (PVC) and Oriented Polyvinyl Chloride (PVCO) for Underground Fire Service (Sixth Edition).pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1285 Pipe and Couplings, Polyvinyl Chloride (PVC), and Oriented Polyvinyl Chloride (PVCO) for Underground Fire Service STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER R

2、EPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Pipe and Couplings, Polyvinyl Chloride (PVC), and Oriented Polyvinyl Chloride (PVCO) for Underground Fire Servic

3、e, UL 1285 Sixth Edition, Dated March 15, 2016 SUMMARY OF TOPICS: This new edition of UL 1285 includes the following changes: Added requirements to address non-encapsulated plastic materials used in joint seals Clarication of intent of test pressure based on wall thickness and that samples need not

4、contain a bell Clarication of representative samples for multiple pressure classes of pipe Added Manufacture Installation Instructions The requirements are substantially in accordance with Proposal(s) on this subject dated September 11, 2015. All rights reserved. No part of this publication may be r

5、eproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the

6、implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Stan

7、dard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree

8、 to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. MARCH 15,

9、2016 UL 1285 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARCH 15, 2016 UL 1285 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL March 15, 2016 1 UL 128

10、5 Standard for Pipe and Couplings, Polyvinyl Chloride (PVC), and Oriented Polyvinyl Chloride (PVCO) for Underground Fire Service First Edition January, 1982 Second Edition March, 1991 Third Edition April, 1995 Fourth Edition April, 2001 Fifth Edition July, 2008 Sixth Edition March 15, 2016 This UL S

11、tandard for Safety consists of the Sixth Edition. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Saf

12、ety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2016 UNDERWRITERS LABORATORIES INC.UL C

13、OPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARCH 15, 2016 UL 1285 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .4 2 Units of M

14、easurement .4 3 Components 4 4 Undated References 5 5 Glossary .5 CONSTRUCTION 6 Materials .5 7 Pipe Joints .6 8 Wall Thickness .6 9 Imperfections .6 10 Sealing Gaskets .6 PERFORMANCE 11 General .7 12 Elastomeric Parts 7 13 Sealing Gaskets and Plastic Components 8 14 Short-Term Hydrostatic-Pressure

15、Test 9 15 Leakage Test for Joints 10 16 Assembly Test .10 17 Flattening Test .11 18 Impact Resistance Test 11 19 Material Tensile-Strength Test 11 20 Long-Term Hydrostatic-Pressure Test .11 21 Extrusion Quality Test .12 22 Pipe Intended for Potable Water Supply .12 MANUFACTURING AND PRODUCTION TESTS

16、 23 General 12 24 Production-Line Hydrostatic-Pressure Test .12 MARKING 25 General 13 26 Pipe .14 27 Couplings 14 28 Rubber Gaskets 14 MANUFACTURING AND INSTALLATION INSTRUCTIONS 29 Installation Instructions 15 MARCH 15, 2016 UL 1285 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION O

17、R DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover polyvinyl chloride (PVC) and oriented polyvinyl chloride (PVCO) pressure pipe, couplings, and gaskets for use in underground re service systems and connections to such systems. The pipe is either the distribu

18、tion or transmission type. 1.2 Distribution pipe covered by these requirements shall be designated as Pressure Class 165, 235, and 305 for working pressures of 165, 235, and 305 psig (1.14, 1.62, and 2.10 MPa), respectively, and have a nominal inside diameter in the range of 4 to 12 inches. 1.3 Tran

19、smission pipe covered by these requirements shall be designated as Pressure Class 100, 125, 160, 165, 200, 235, and 305 for working pressures of 100, 125, 160, 165, 200, 235, and 305 psig (0.69, 0.86, 1.10, 1.14, 1.38, 1.62, and 2.10 MPa), respectively, and have a nominal inside diameter in the rang

20、e of 14 to 48 inches. 1.4 Requirements for the installation and use of PVC pressure pipe and couplings are specied in the Standard for the Installation of Private Fire Service Mains and their Appurtenances, NFPA 24 or the Standard for the Installation of Sprinkler Systems, NFPA 13. 2 Units of Measur

21、ement 2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 3 Components 3.1 Except as indicated in 3.2, a component of a product covered by this standard shall comply with the requirements for that component. 3.2 A component is

22、not required to comply with a specic requirement that: a) Involves a feature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 3.3 A component shall be used in accordance with its rating

23、established for the intended conditions of use. 3.4 Specic components are incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used on

24、ly under those specic conditions. MARCH 15, 2016 UL 1285 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4 Undated References 4.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interprete

25、d as referring to the latest edition of that code or standard. 5 Glossary 5.1 For the purposes of this Standard, the following denitions apply. 5.2 GASKET SEATING AREA The section of pipe or coupling that is, or has the potential to be, in contact with the sealing surfaces of the gasket in intended

26、assemblies. 5.3 PIPE SIZE The nominal outside diameter of pipe that is compatible with cast iron pipe or steel pipe (IPS) of the same nominal size. 5.4 WORKING PRESSURE The maximum anticipated sustained pressure applied to the pipe exclusive of pressure surges. CONSTRUCTION 6 Materials 6.1 PVC pipe

27、and couplings shall: a) Be made from Cell Class 12454 virgin compounds, as dened in the Standard Specication for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds, ANSI/ASTM D1784 except as allowed by 6.3; and b) Have an established hydrostatic-design

28、-basis (HDB) rating of 4000 psig (27.6 MPa) for water at 73.4F (23.0C). 6.2 PVCO pipe shall: a) Be made from Cell Class 12454 virgin compounds, as dened in the Standard Specication for Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds, ANSI/ASTM D1784

29、 except as allowed by 6.3; and b) After expansion, have an established hydrostatic-design-basis (HDB) rating of 7100 psig (49.0 MPa) for water at 73.4F (23.0C). 6.3 Noncontaminated PVC and PVCO pipe from the manufacturers production that is reground, or pelletized, and dry blended by the manufacture

30、r with the same grade and Cell Class of PVC virgin material, is not prohibited from being used provided that the blended material is of the same Cell Class of PVC pipe material and the nished product complies with the requirements of this standard. 6.4 The outside diameter of the pipe shall be compa

31、tible with the (OD) dimensions of cast-iron pipe. MARCH 15, 2016 UL 1285 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 6.5 The outside diameter of pipe shall be permitted to be compatible with the (OD) dimensions of steel pipe when fabric

32、ated in accordance with the dimension requirements in AWWA C905. 7 Pipe Joints 7.1 If a coupling is used to join the pipe ends, the coupling with sealing ring gaskets shall be furnished with each length of pipe. Each coupling shall be of the same composition, trade size, and Pressure Class as the pi

33、pe. 7.2 If a bell-and-spigot joint is used, a sealing gasket shall be furnished with each length of pipe. 8 Wall Thickness 8.1 For PVC pipe, the minimum wall thickness for each size and Pressure Class shall be as specied in the Standard for Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fitti

34、ngs, 4 In. Through 12 In. (100 mm Through 300 mm), for Water Transmission and Distribution, ANSI/AWWA C900, or the Standard for Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 14 Inches Through 48 Inches (350 mm Through 1,200 mm), for Water Transmission and Distribution , ANSI/AWWA C

35、905, whichever standard is appropriate. 8.2 For PVCO pipe, the minimum wall thickness for each size and Pressure Class shall be as specied in the Standard for Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe, 4 in. Through 24 in. (100 mm Through 600 mm), for Water Distribution, ANSI/AWWA

36、 C909. 9 Imperfections 9.1 Pipe shall be homogeneous throughout and shall have no voids, cracks, inclusions, or other defects that impair the intended performance of the product. 9.2 Axial dents, gouges, bruises, tool marks, or grooves in the gasket seating area of a pipe section or coupling shall n

37、ot be deeper than 1/32 inch (0.8 mm). 10 Sealing Gaskets 10.1 A sealing gasket shall be made of a vulcanized natural rubber or a synthetic rubber compound and shall have uniform dimensions and sufficient thickness to provide a compression-like seal. See Elastomeric Parts, Section 12. MARCH 15, 2016

38、UL 1285 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL PERFORMANCE 11 General 11.1 Representative samples of each Pressure Class and nominal size of PVC pipe and couplings shall be subjected to the tests described in Sections 12 21. 12 Ela

39、stomeric Parts 12.1 An elastomeric part used to provide a seal shall have the following properties when representative samples are tested as specied in the Standard for Gaskets and Seals, UL 157: a) Single material and sealing (soft) portion of dual material gaskets: 1) Minimum tensile strength 2000

40、 psi (13.8 MPa), and minimum ultimate elongation 300 percent 1 to 4 inches (25.4 to 102 mm). 2) Maximum set of 3/16 inch (4.8 mm) when 1 inch (25.4 mm) marks are stretched to 3 inches (76.2 mm), held for 2 minutes, released, and measured 2 minutes after release. 3) Those properties relating to minim

41、um tensile strength and elongation after oven aging; and hardness after oven aging, all as specied in UL 157. The maximum service temperature used to determine the oven time and temperature for oven aging is 60C (140F). 4) The compression set of samples of rubber seals shall not exceed 20 percent of

42、 the original thickness after being compressed to three-fourths of the original thickness. b) Retaining (hard) portion of dual material gaskets: 1) Minimum tensile strength 1200 psi (8.3 MPa), and minimum ultimate elongation 125 percent 1 to 2.25 inches (25.4 to 57.2 mm). 2) Those properties relatin

43、g to minimum tensile strength and elongation after oven aging as specied in UL 157. The maximum service temperature used to determine the oven time and temperature for oven aging is 60C (140F). MARCH 15, 2016 UL 1285 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WI

44、THOUT PERMISSION FROM UL 13 Sealing Gaskets and Plastic Components 13.1 Sealing gaskets containing plastic components that are not fully encapsulated and are intended to function as an active component for the sealing gasket shall meet the requirements of this section. 13.2 Following air-oven aging

45、for 180 days at 121C (250F), there shall be no warping, creeping, or other signs of deterioration of a plastic component that may preclude the intended operation of the joint seal. There shall be no cracking of any plastic component. A joint with aged plastic components shall demonstrate acceptable

46、performance when subjected to the Leakage Test for Joints, Section 15 and the Assembly Test, Section 16. 13.3 A complete sealing gasket, including the plastic components to be aged are to be supported in a full-draft, circulating-air oven that has been preheated at full draft, to 121 1C (250 8F). Th

47、e manufacturer may exclude the elastomeric portion of the sealing gasket from aging. The manner of support is to be such that the samples are prevented from touching one another or the sides of the oven. The samples are to be aged for 180 days at full draft and then allowed to cool in air at 23 2C (

48、73.4 3.6F) for at least 24 hours before conducting any test or dimensional check. Prior to any tests, elastomeric components of the sealing gasket shall be added to the sealing gasket if not included in the aging test. As used in this test, the term full draft refers to the air ow over the samples i

49、n the oven with the air inlet and outlets fully open. The oven used for accelerated aging is to be Type IIA as specied in the Standard Specication for Gravity-Convection and Forced-Ventilation Ovens, ASTM E145. 13.4 If a plastic material cannot withstand the temperature indicated without softening, distortion, or deterioration, an air-oven aging test at a lower temperature for a longer period of time may be used. If a material is capable of withstanding a higher t