UL 1040-1996 UL Standard for Safety Fire Test of Insulated Wall Construction (First Edition Reprint with Revisions Through and Including April 26 2017)《绝缘墙体结构的燃烧试验》.pdf

《UL 1040-1996 UL Standard for Safety Fire Test of Insulated Wall Construction (First Edition Reprint with Revisions Through and Including April 26 2017)《绝缘墙体结构的燃烧试验》.pdf》由会员分享，可在线阅读，更多相关《UL 1040-1996 UL Standard for Safety Fire Test of Insulated Wall Construction (First Edition Reprint with Revisions Through and Including April 26 2017)《绝缘墙体结构的燃烧试验》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1040 Fire Test of Insulated Wall ConstructionUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED

2、FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Fire Test of Insulated Wall Construction, UL 1040 First Edition, Dated August 9, 1996 Summary of Topics This revision to ANSI/UL 1040 is being issued to reect the recent reaffirmation of UL 1040 as an Amer

3、ican National Standard. No changes have been made to the requirements within this Standard. Text that has been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and

4、 are followed by an effective date note indicating the date of publication or the date on which the changed requirement becomes effective. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical

5、 photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any sp

6、ecial, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage.

7、In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim

8、, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or

9、other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. OCTOBE

10、R 30, 2012 UL 1040 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 30, 2012 UL 1040 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 9, 1996

11、(Title Page Reprinted: October 30, 2012) 1 UL 1040 Standard for Fire Test of Insulated Wall Construction Prior to the rst edition, the requirements for the products covered by this standard were included in the Outline of Investigation for Insulated Wall Construction, Subject 1040. First Edition Aug

12、ust 9, 1996 This ANSI/UL Standard for Safety consists of the First Edition including revisions through October 30, 2012. The most recent designation of ANSI/UL 1040 as a Reaffirmed American National Standard (ANS) occurred on October 30, 2012. ANSI approval for a standard does not include the Cover

13、Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs

14、 Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2012 UNDERWRITERS LAB

15、ORATORIES INC. ANSI/UL 1040-2001 (R2012)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL OCTOBER 30, 2012 FIRE TEST OF INSULATED WALL CONSTRUCTION - UL 1040 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

16、 OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .5 2 General 6 2.1 Units of measurement .6 2.2 Undated references .6 PERFORMANCE LARGE SCALE CORNER TEST 3 General 6 4 Ignition Source .6 5 Fire Test Room and Geometry .7 6 Protection and Conditioning of Test Assembly 7 7 Fire

17、 Test Room Environment .8 7.1 Ventilation .8 7.2 Ambient conditions in test room 8 8 Instrumentation .8 8.1 Ignition source monitoring thermocouples 8 8.2 Test measurement thermocouples 8 8.3 Visual records .11 9 Test Procedure 11 REPORT 10 General 11 10.1 Materials 11 10.2 Humidity and temperature

18、.11 10.3 Temperature development .12 10.4 Time history of re growth .12 10.5 Specimen conditions 12 11 Compliance Criteria .12 SEPTEMBER 18, 2007 FIRE TEST OF INSULATED WALL CONSTRUCTION - UL 1040 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FRO

19、M UL This page intentionally left blank. SEPTEMBER 18, 2007 FIRE TEST OF INSULATED WALL CONSTRUCTION - UL 1040 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 This test method describes the testing procedures and re

20、quirements applicable to insulated wall constructions by use of a standardized large-scale corner test. 1.2 The purpose of this test method is to determine the ability of eld or prefabricated insulated wall panels to resist the spread-of-ame over a simulated interior wall surface of a building and t

21、he ability of the insulating material to resist damage as a result of the re exposure. This test method is not intended to evaluate the re resistance afforded by the structural members of the test structure such as columns, beams, girders, bar joists, tie bars, and the like. 1.3 These requirements d

22、o not cover the evaluation of panels intended for various uses other than as specied in 1.1 for which there are other established test standards as follows: a) Surface Burning Characteristics Classication Establishes the comparative burning characteristics of building materials and assemblies by mea

23、surement of ame spread over exposed surfaces and the density of the smoke developed during the re exposure period. This test method is described in the Standard for Test for Surface Burning Characteristics of Building Materials, UL 723. b) Fire-Resistance (hourly rating) Establishes hourly re resist

24、ance ratings of building assemblies through large-scale re exposures under specic loading conditions. This test method is described in the Standard for Fire Tests of Building Construction and Materials, UL 263. c) Roof-Covering Materials Establishes performance measurements for coverings relative to

25、 resistance to exterior re spread and penetration. This test method is described in the Standard for Test Methods for Fire Resistance of Roof-Covering Materials, UL 790. d) Roof-Deck Construction Materials Establishes performance measurements for roong systems with respect to resistance to the sprea

26、d-of-ame and damage from underdeck interior re exposure. This test method is described in the Standard for Fire Test of Roof Deck Constructions, UL 1256. 1.3 revised June 8, 2001 1.4 A product that contains features, characteristics, components, materials, or systems new or different from those cove

27、red by the requirements in this standard, and that involves a risk of re or of electric shock or injury to persons shall be evaluated using appropriate additional component and end-product requirements to maintain the level of safety as originally anticipated by the intent of this standard. A produc

28、t whose features, characteristics, components, materials, or systems conict with specic requirements or provisions of this standard does not comply with this standard. Revision of requirements shall be proposed and adopted in conformance with the methods employed for development, revision, and imple

29、mentation of this standard. 1.4 revised June 8, 2001 JUNE 8, 2001 FIRE TEST OF INSULATED WALL CONSTRUCTION - UL 1040 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2.1 Units of measurement 2.1.1 Values stated without parentheses

30、are the requirement. Values in parentheses are explanatory or approximate information. 2.1.1 revised June 8, 2001 2.2 Undated references 2.2.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that co

31、de or standard. PERFORMANCE LARGE SCALE CORNER TEST 3 General 3.1 A nominal 764 10 pound (347 4.54 kg) wood crib is to be used to produce a uniform ame for direct impingement on the walls and ceiling of a 20 by 20 by 30 foot (6.10 by 6.10 by 9.14 m) high open corner conguration. The contribution of

32、the wall assembly to re growth is to be dened in terms of: a) The time history of temperature development within the corner conguration; b) The maximum observed ame progression; c) Post-test damage of the sample. 3.2 A report of the test results shall be prepared as specied in Report, Section 10. 4

33、Ignition Source 4.1 The ignition source for the test is to be a wood crib weighing 764 10 pounds (347 4.54 kg) having dimensions of 4 by 4 by a minimum of 3-1/2 ft high (1.22 by 1.22 by 1.07 m), and constructed of 12 tiers of kiln dried spruce, pine, r, or other soft woods having densities similar t

34、o those named, and are to be dried to a moisture content of 9 to 11 percent as determined by the procedures described in paragraph 4.3. Each strip is to be 4 ft. long, and is to have a cross section of trade size 2- by 4-inch nominal 1-1/2 by 3-1/2 inches (38.1 by 89 mm). Within the crib, the strips

35、 in each tier are to be evenly spaced and lie at right angles to the strips in the tier below. 4.1 revised June 8, 2001 4.2 The wood crib is to be positioned 1 foot (305 mm) from each wall and is to be ignited by two torches formed from 3-1/2 inch (88.90 mm) diameter by 6 inch (152.40 mm) long rolls

36、 of cotton waste, each saturated with 8 ounces (0.23 kg) of n-heptane. The torches are to be ignited simultaneously, inserted immediately into the bottom tier and positioned at the center of one of four quadrants (based on plan view cross-sectional area) for 15 s (30 s elapsed time) and then removed

37、. Ignition time is considered to be the instant the torches are inserted into the wood crib. 4.2 revised June 8, 2001 JUNE 8, 2001 FIRE TEST OF INSULATED WALL CONSTRUCTION - UL 1040 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4.3 Moistu

38、re content of the wood is to be monitored by using either a conductance or dielectric-type meter (calibrated as described in the Standard Test Methods for Use and Calibration of Hand-Held Moisture Meters, ASTM D-4444) until the desired level is reached. Final determination of moisture content shall

39、be based on the secondary oven-drying method (Method B) described in the Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials, ASTM D-4442. 4.3 added June 8, 2001 5 Fire Test Room and Geometry 5.1 The test structure is to be constructed from the insulated wal

40、l construction materials under investigation. These materials are to be installed in the required framework so as to form two vertical walls intersecting to describe a 90-degree angle to form a 20 by 20 by 30 feet (6.10 by 6.10 by 9.14 m) high structure. The construction is to be representative of e

41、ld construction. The two open sides of the test structure are considered to represent the greater open volume of a building. 5.2 An uninsulated at-metal roof, nominally 20 by 20 feet (6.10 by 6.10 m), is to be placed over the test structure. The walls are to be joined to the roof in a manner represe

42、ntative of eld-joining methods. (Since the presence of combustible material on the underside of the ceiling can inuence the performance of walls, the results of this test are applicable only to constructions with noncombustible material on the interior ceiling surface.) 5.2 revised June 8, 2001 6 Pr

43、otection and Conditioning of Test Assembly 6.1 Prior to mounting, specimens are to be conditioned at a temperature of 73 4F (22.8 2.2C) and a relative humidity of 50 5 percent until constant weight is achieved. 6.2 The test assembly is to be mechanically protected during and after mounting to provid

44、e for its integrity at the time of test. Assemblies are not to be tested until nal material conditioning has been attained. Materials containing moisture or solvents are to achieve constant weight condition prior to test. 6.2 revised June 8, 2001 6.3 In addition, 2-foot (0.61 m) high draft curtains

45、are to be suspended from the underside of the at roof along the open sides of the test structure. The draft curtains are to be composed of noncombustible material. 6.3 revised June 8, 2001 6.4 Deleted June 8, 2001 JUNE 8, 2001 FIRE TEST OF INSULATED WALL CONSTRUCTION - UL 1040 7UL COPYRIGHTED MATERI

46、AL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 7 Fire Test Room Environment 7.1 Ventilation 7.1.1 The re test room is to be located within a building vented to discharge combustion products and intake fresh air. 7.2 Ambient conditions in test room 7.2.1 The amb

47、ient conditions in the test room, measured at the center of the test room, at the time of test are to be a minimum of 60F (15.6C) and a maximum of 70 percent relative humidity. 8 Instrumentation 8.1 Ignition source monitoring thermocouples 8.1.1 The ignition source monitoring thermocouples are to be

48、 constructed of No. 14 gauge (5.03 mm 2 ) bare chromel-alumel wire mounted in ceramic insulation and placed within a 1/2 inch, Schedule 40 pipe (see the Standard for Welded and Seamless Wrought Steel Pipe, ANSI/ASME B36.10M). The bare thermocouple junction is to protrude 1 inch (25.4 mm) beyond the

49、end of the ceramic insulation and 3 inches (76 mm) beyond the end of the pipe. 8.1.1 revised June 8, 2001 8.1.2 Thermocouples are to be placed over the exposed re crib, as shown in Figure 8.1, to determine and record the character and temperature of the re. 8.2 Test measurement thermocouples 8.2.1 Test measurement thermocouples are to be constructed of No. 24 gauge (1.60 mm 2 ) bare chromel-alumel wire. The thermocouple wire within 0.5 inch (13 mm) of the thermocouple ju