TIA-604-17-2004 FOCIS 17 Fiber Optic Connector Intermateability Standard Type MU《FOCIS 17 光纤连接器互匹配性标准 类型 MU》.pdf

《TIA-604-17-2004 FOCIS 17 Fiber Optic Connector Intermateability Standard Type MU《FOCIS 17 光纤连接器互匹配性标准 类型 MU》.pdf》由会员分享，可在线阅读，更多相关《TIA-604-17-2004 FOCIS 17 Fiber Optic Connector Intermateability Standard Type MU《FOCIS 17 光纤连接器互匹配性标准 类型 MU》.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-604-17 February 2004 (r 01/2012) FOCIS 17 Fiber Optic Connector Intermateability Standard, Type MU NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeabil

2、ity and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling pr

3、oducts not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Sta

4、ndards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all appli

5、cable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Project No.3-0076, formulated under the cognizance of the TIA TR-42 Telecommuni

6、cations Cabling Systems, TR-42.13 Subcommittee on Passive Optical Devices and Fiber Optic Metrology). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICAT

7、IONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA.

8、 Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for d

9、etails on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any

10、 other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or mor

11、e parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, an

12、d disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or cond

13、itions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by anoth

14、er organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4t

15、hedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent

16、(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor

17、compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRAN

18、TIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES

19、NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR A

20、NY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BA

21、SED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY

22、 TIA WITHOUT SUCH LIMITATIONS. TIA 604-17 FOCIS 17 FIBER OPTIC CONNECTOR INTERMATEABILITY STANDARD TYPE MU CONNECTOR CONTENTS 1 INTRODUCTION 1 2 ADAPTER STANDARD 2 3 PLUG STANDARD 3 4 APPLICATIONS 6 5 POLARIZATION MAINTENANCE 6 ANNEX A (INFORMATIVE) FLOATING DUPLEX CONNECTOR PLUG 20 ANNEX B (INFORMA

23、TIVE): BACKPLANE APPLICATION 21 SP-3-0076 (To be TIA/EIA-604-17, FOCIS 17) iiTIA 604-17 1 FOCIS-17 FIBER OPTIC CONNECTOR INTERMATEABILITY STANDARD TYPE MU CONNETOR (From TIA Standards Proposal No. 3-0076 formulated under the cognizance of TIA FO-6.3, Subcommittee on Fiber Interconnecting Devices.) T

24、his document is part of the series of test standards included within TIA/EIA-604, Fiber Optic Connector Intermateability Standards (FOCIS). 1 INTRODUCTION 1.1 Scope FOCIS 17 presents the intermateability standard for connectors with the commercial designation MU, and is issued as an addendum to TIA/

25、EIA 604, Fiber Optic Connector Intermateability Standards. The provisions of TIA/EIA 604 apply to this document. 1.2 Objective Intermateability standards define the minimum physical attributes of mating connector components. Fully dimensioned components are not within the scope or intent of FOCIS 17

26、. The requirements in FOCIS 17 have been selected with the objective of ensuring that any combination of plugs and adapters conforming to the requirements of FOCIS 17 will mechanically intermate, and that intermated connector assemblies will meet their common level of performance. The common level o

27、f performance of an intermated connector assembly is the least demanding set of performance requirements in the separate performance specifications of each of the products in the assembly; see TIA/EIA 604. 1.3 Limitations Realization of the objectives for FOCIS 17 may be limited by the following con

28、siderations: 1.3.1 Configuration options There are configuration options for both plugs and adaptors in FOCIS 17 that impose limitations on the combinations of plugs and adaptors that should be selected in a connector assembly. Both plugs should have the same ferrule diameter option, t. An assembly

29、with different diameter options may have a higher loss than anticipated. Both plugs should have the same angle of contact option a. An increase in loss may be expected if the plugs with different options are mated, and the polish on the ferrule may be damaged. SP-3-0076 (To be TIA/EIA 604-17, FOCIS

30、17) 21.3.2 Common performance The following considerations limit the application of common performance. The location of the fiber cores, figure 3.2.6, and the apex offsets, clause 3.2.4, are defined, without tolerances, by their true positions. To achieve common performance, the distributions of the

31、 actual positions of these features should be centered on their respective true positions. Tuning of the connector plugs may improve performance when plugs are mated with plugs that have been similarly tuned. Tuned plugs, o=1, are assembled so the fiber core of the plug falls in a preferred location

32、 with respect to the key; see clause 3.2.6. The common level of performance of connector plugs that have been tuned shall be based on their untuned performance; see TIA/EIA 604, section 7. This standard does not control the intrinsic loss that may occur between fibers in a connector assembly. Intrin

33、sic loss between fibers must be added to the basic connector loss. 1.3.3 Resolution Cases of combinations of plugs and adapters where mechanical intermateability or the common level of performance is not achieved should be resolved through the cooperation of the user and the connector and adapter ma

34、nufacturer(s). 1.4 Drawing practices To be in compliance with ANSI and ISO Engineering Drawing Practices, the following shall apply: 1. Where a tolerance of form is not specified, the limits of the dimensions for a feature control the form as well as the size. The combined effects of size and form v

35、ariations may not exceed the envelope of perfect form at the maximum material condition (MMC). 2. Where interrelated features of size (features shown with a common axis or center plane) have no geometric tolerance of location or runout specified, the limits of the dimensions for a feature control th

36、e location tolerance as well as the size. When interrelated features are at the MMC they shall be perfectly located to each other as indicated by the drawing. 3. Where perpendicular features (features shown at right angles) have no geometric tolerance or orientation or runout specified, the limits o

37、f the dimensions for a feature control the orientation tolerance as well as the size. When perpendicular features are at the MMC they shall be perfectly oriented to each other as indicated by the drawing. 4. As the size of a feature departs from the MMC, variations in form, location and orientation

38、are permissible. 2 ADAPTER STANDARD 2.1 Adapter designation The designation for a FOCIS 17 adapter is: FOCIS 17A-d-n-m where TIA 604-17 3 A designates that it is the adapter d defines the adaptor design n is the number of fibers m defines the mounting configuration 2.2 Adapter requirements FOCIS 17

39、adapters shall meet the requirements of this section. 2.2.1 Adapter interface dimensions The dimensional requirements for FOCIS 17 adapters are defined as follows: d=1, n=1 - Figure 2.2.1a Simplex Adapter Interface d=1, n=2 - Figure 2.2.1b, Duplex Adapter Interface, separated plug arrangement, plugs

40、 arranged based on 6.25 mm center to center spacing. d=2, n=2 - Figure 2.2.1c, Duplex Adapter Interface, dense plug arrangement, plugs arranged based on 4.5 mm center to center spacing. 2.2.2 Adapter sleeve The adapter sleeve may be a split (resilient) sleeve, and the sleeve may be either fixed or f

41、loating within the adapter. The minimum inside diameter of the sleeve is specified by the force required to remove a gage pin from the sleeve. The force required to remove a gage pin from the sleeve in a FOCIS 17 adapter shall be 1.0 N (Newton) to 2.5N. The procedures of FOTP 158 shall be used to me

42、asure the withdrawal force. Gage pin diameters are specified in table 1. Table 1 - Gage pin diameters Sleeve Type Minimum Diameter (mm) Maximum Diameter (mm) Split, Resilient 1.2485 1.2495 The maximum inside diameter of the sleeve is in effect limited by the common level of performance that the adap

43、ter is to achieve. The surface roughness of the gage pin should be grade N4 (0.2 m radius). 2.2.3 Adapter mounting options The adapter mounting options specified is m=0. The mounting features for this option are undefined. 3 PLUG STANDARD 3.1 Plug designation The complete designation for a FOCIS 17

44、connector plug is: FOCIS 17P-d-n-t-a-o SP-3-0076 (To be TIA/EIA 604-17, FOCIS 17) 4where, P designates that it is the plug d defines the plug design n is the number of fibers t defines the ferrule diameter a is the angle of contact o defines the plug tuning 3.2 Plug requirements FOCIS 17 plugs shall

45、 meet the requirements of this section. 3.2.1 Plug interface option There are two plug interface options for FOCIS 17 plugs. The requirements for these interfaces are: d=1 The elements of the plug(s) that control the interface with the adapter are for the separated plug arrangement, and must meet th

46、e dimensional requirements of figure 3.2.1a, Plug interface (d=1). The distance between the plug ferrules is nominally 6.25 mm center to center when two plugs are arranged in duplex. d=2 The elements of the plugs that control the interface with the adapter are for the dense plug arrangement and must

47、 meet the dimensional requirements of figure 3.2.1b, Plug interface (d=2). The distance between the plug ferrules is 4.5 mm center to center when two plug ferrules are arranged. 3.2.2 Number of fibers option Plugs with option n=1, figure 3.2.1a, designates a simplex plug. Plugs with option n=2, figu

48、re 3.2.1b, designates a duplex plug. 3.2.3 Ferrule diameter option Ferrule diameters for FOCIS 17 plugs are specified in table 2. Table 2 Ferrule diameter t Minimum (mm) Maximum (mm) Fiber 1 1.2483 1.2495 Single-mode, Multimode 2 1.2485 1.2495 Single-mode, Multimode 3 1.2467 1.2495 Multimode The fer

49、rule tolerances t=1 and t=2 are typically applied to plugs with single-mode fiber. The ferrule tolerance t=3 is typically applied to plugs with multimode fiber. 3.2.4 Angle of contact option Contact angle is the angle that the plane of contact makes to a plane perpendicular to the axis of the ferrule. The plane of contact is defined as plane A-A in figure 3.2.4 (a). a=0, designates an angle of 0 a=8, designates an angle of 8 Requirements: TIA 604-17 5 For a=0, and a=8: The true position for the apex is at the center of the ferrule as projected on the plane of contact in figure 3.2