TIA-455-134-1997 FOTP-134 Measurement of Connector Ferrule Hole Inside Diameter《FOTP-134 连接器密套环孔内径的测量》.pdf

《TIA-455-134-1997 FOTP-134 Measurement of Connector Ferrule Hole Inside Diameter《FOTP-134 连接器密套环孔内径的测量》.pdf》由会员分享，可在线阅读，更多相关《TIA-455-134-1997 FOTP-134 Measurement of Connector Ferrule Hole Inside Diameter《FOTP-134 连接器密套环孔内径的测量》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、TIA STANDARD ANSI/TIA-455-134-1996 Approved: December 27, 1996 Reaffirmed: December 3, 2002 FOTP-134 Measurement of Connector Ferrule Hole Inside Diameter TIA-455-1 34 JANUARY 1997 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Representing the lelccornrnunications industry in association with lhe Electron

2、ic Industria Alliance Electronic Industri- Alliance Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA Engineering Standards and Publications are designed to serve the public int

3、erest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and P

4、ublications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically

5、or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or P

6、ublication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory lim

7、itations before its use. (From Standards Proposal No. 3-3366-RF1, formulated under the cognizance of the TIA FO-4.3 Subcommittee on Interconnecting Devices.) This Document was reaffirmed by the American National Standards Institute (ANSI) on December 3,2002 and by the TIA. Published by TELECOMMUNICA

8、TIONS INDUSTRY ASSOCIATION 1997 Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-80

9、0-854-7179) International (303-397-7956) or search online at http:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license

10、 from IHS-,-,-Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed has been prepared by one or mo

11、re Engineering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees are expected to

12、conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.orrr/standards/sfrr/enrrineerinn manual.cfm. TIAS function is to administer the process, but not the content, of document preparation in

13、accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY INVOLVE THE USE OF INTELLECTUAL PROPERTY RIGHTS (“IPR), INCLUDING PENDING OR ISSUED PATENTS, OR COPYRIGHTS, OWNED B

14、Y ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR. WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEMENT FROM THE HOLDER THEREOF IS REQUESTED, ALL IN ACCORDANCE WITH THE MANUAL. TIA TAKES NO POSITION WITH REFERENCE TO

15、, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SCOPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR

16、 PURPOSE PARTYS INTELLECTUAL PROPERTY RIGHTS. TIAEXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION. OR USE, ITS MERCHANTABILITY AND ITS NON-INF

17、RINGEMENT OF ANY THIRD TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, L

18、OSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS

19、HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-V I TINEIA-455-I 34 FOTP-134 Measurement of connector f

20、errule hole inside diameter Contents 1 . Introduction . - 1.1 Intent 1 1.2 Accuracy and precision 1 1.3 Applications . 1 2 . Applicable documents . 1 3 . Apparatus 2 3.1 Connector or ferrule holder . 2 3.2 Calibrated wire holder . 2 3.3 Calibrated wire set 2 4 . Sampling andspecimens . 2 5 . Procedu

21、re 3 6 . Calculations or interpretation of results 3 7 . Documentation . 3 7.1 Allapplications . 3 7.2 United States military 4 . 8 . Specification information . 4 AnnexA . 5 i Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking

22、permitted without license from IHS-,-,-TINEIA-455-1 34 (This page left blank) Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-EIA TIA-Y55-134-ENGL 1997 3234b00 0580538 827 TINEIA-455

23、-1 34 FOTP-I 34 Measurement of connector ferrule hole inside diameter (From EIA Standards Proposal No. 3366, formulated under the cognizance of TIA FO-6.3, Subcommittee on Fiber Optic Interconnecting Devices.) This FOTP is part of the series of test procedures included within Recommended Standard EI

24、MIA- 455. I Introduction 1.1 Intent The intent of this procedure is to determine the inside diameter of the ferrule hole in an optical fiber connector ferrule. 1.2 Accuracy and precision The precision of the method is affected by the incremental differences in the outer diameters of the calibrated w

25、ire set used for the measurement. The accuracy of the method is controlled by the calibration of the calibrated wire set. 1.3 Applications This procedure is applicable to all optical fiber connectors. 2 Applicable documents Test or inspection requirements may include, but are not limited to, the fol

26、lowing references: EIMIA-455-A Standad Test Procedures for Fiber optic Fibers, Cables, Transducers, Sensors, Connecting and Terminating Devices, and Other Fiber Opfic Components 1 c Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networ

27、king permitted without license from IHS-,-,- - STD-EIA TIA-455-134-ENGL 1777 3234b00 0580539 7b3 TINEIA-455-1 34 3 Apparatus - 3.1 Connector or ferrule holder (optional) Use a connector or ferrule holder to hold the optical fiber connector or ferrule during the measurement. 3.2 Calibrated wire holde

28、r (optional) Use a wire holder to hold the calibrated wires during the measurement. 3.3 Calibrated wire set Use a calibrated wire set with outside diameters that encompass the ferrule inside diameter specified in the Detail Specification that meets the following requirements: a. b. C. Unless otherwi

29、se specified, use wires that have known outside diameters (traceable to NIST) with a tolerance of -0.0, W.25 pm. Unless otherwise specified, use a wire set with maximum differences in the diameters of consecutive wires of 2 percent of the wire diameter. For single-mode ferrules, use a wire set that

30、includes at least one wire with an outside diameter equal to the ferrule inside diameter specified in the Detail Specification. For multimode ferrules, use a wire set that includes wires having outer diameters equal to the maximum and minimum sizes specxfied in the Detail Specification. If a wire in

31、 the set is used for more than one test specimen, periodically verify the outer diameter calibration of the wire. d. e. 4 Sampling and specimens Unless otherwise specified in the Detail Specification, use an optical fiber connector ferrule for the test specimen. The specimen may be part of an optica

32、l fiber connector at the time of measurement. Keep the specimen free from dirt or dust with a front surface polished sufficiently to allow delineation of the boundaries of the hole. NOTE: Always clean the specimen at some time before performing this test procedure. 2 Copyright Electronic Industries

33、Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - STD=EIA TIA-455-134-ENGL 1997 3234b00 05805LiO Y85 m TINEIA-455-1 34 - 5 Procedure 5.1 Unless otherwise specified in the Detail Specification, precondition the optical

34、 fiber connector or ferrule specimen for 6 hours at standard atmospheric conditions as specified in EIAiTIA-455-A. 5.2 If applicable, place the optical fiber connector or ferrule specimen in the optical fiber connector or ferrule holder. 5.3 Choose one wire of the calibrated wire set (the smallest w

35、ire is recommended). If applicable, place the wire in the calibrated wire holder. Insert the wire into the ferrule until it extends completely through the ferrule from one end to the other. 5.4 Remove the wire and repeat the procedure for the rest of the remaining wires (it is recommended that the s

36、mallest remaining wire be used each time) until all of the wires have been inserted or until it is not possible to completely insert a wire into the ferrule. 6 Calculations or interpretation of results The connector ferrule inside diameter reported is the diameter of the largest wire that can be pas

37、sed completely through the connector ferrule. 7 Documentation 7.1 All applications Report the following information for each test: 7.1 .I Date and title of the test. 7.1.2 Identification of procedure (FOTP-XXX). 3 Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for

38、 ResaleNo reproduction or networking permitted without license from IHS-,-,-TlNEIA-455-134 7.1.3 Test specimen identification. 7.1.4 Connector ferrule inside diameter. 7.1.5 Incremental difference in the outer diameters of the wires in the wire set. 7.2 United States military United States military

39、applications require that the following information also be reported for each test. For other (nonmilitary) applications, this information need not be reported but shall be available for review upon request: 7.2.1 Test personnel. 7.2.2 Brief description of the test apparatus and date of latest calib

40、ration. 8 Specification information The following information shall be specified in the Detail Specification: - 8.1 Connector ferrule inside diameter. 8.2 Test specimen to be tested. 8.3 Number of samples to be tested. 8.4 Preconditioning, if other than that specified in 5.1. 8.5 Wire diameter toler

41、ances, if other than those specified in 3.3a or 3.3b. _- 4 Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD*EIA TIA-q55-13LI-ENGL 1797 = 323Lib00 0580542 258 W TINEIA-455-1 34 Annex A

42、 (informative) Comparison between this FOTP and IEC or ITU/T requirements AI. IEC There are no known IEC documents on this topic matter. M. ITU/T There are no known ITU/T documents on this topic matter. 5 Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo

43、 reproduction or networking permitted without license from IHS-,-,- STD-EIA TIA-qEi5-13q-ENGL 1777 = 3239600 0580593 179 m TINEIA-455-I 34 This page left blank. 6 Copyright Electronic Industries Alliance Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted with

44、out license from IHS-,-,- STD-EIA TIA-455-L34-ENGL 1997 323Lib00 0580544 O20 = FOPT NUMBER PROJECT NUMBER FOTP DATE BALLOT LEVEL O FO-6Committee O SP Standards 1 34 3366 4/20/96 Ballot Proposal I THIS FOTP IS: 1 Ci NEW O A Revision of a Published Document FOTP BACKGROUND DATA SUBCOMMITTEE ORIGIN OF

45、THIS FOTP: SC: F0-6.3 CHAIRPERSON: I Tom Ball AUTHOR AND/OR PREFERRED CONTACT (Name, Address, Telephone): Gair D. Brown NSWCDD 17320 Dahlgren Road, Code 835 Dahlgren, VA 22448-51 O0 540-653-1 579 FOTP SOURCES (Reference documents and other sources used in preparation of this FOTP): CommerciaI/Tviili

46、taFederal Test Methods: Technical Articles: Other Source Material: FO 6.3.3 input PREVIOUS FOTP USAGE (References shown as appropriate): This FOTP represents: O A new conceptual method U Other than given below (see “Other Information) O verified in preliminary laboratory testing.* O not verified in

47、any laboratory testing. O used with electricallelectronic and other components, but not previously applied to Fiber Optics 0 validated in multiple laboratow use.* Ci used in laboratory and manufacturing processes.*# O intended primarily for manufacturing level testing.# O An established method Refer

48、ences: * Laboratories # Representative Manufacturers AT&T AMP 3M ADC Northern Telecom When Used Many Y ears 1 BACKGROUND SHEET PREPARED BY: O Indicated Author O Other, as shown: I (Additional pages used as necessary) - _. FOTP BACKGROUND (Continued) 7 Copyright Electronic Industries Alliance Provide

49、d by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-COMMENTS ON ACCURACY (OR POTENTIAL ACCURACY). REPEATABILITY, ETC. OF THE FOTP: (If Precision and Bias Statements are not included in the FOTP) Experience with this test indicates that the method is accurat